bora PKIW3 Operating And Installation Instructions
Pro induction wok cooktop
Hide thumbs
Also See for PKIW3:
- Installation instructions manual (44 pages) ,
- Operating instructions manual (56 pages)
Related Manuals for bora PKIW3
Summary of Contents for bora PKIW3
- Page 1 Operating and installation instructions PKIW3 BORA Pro induction wok cooktop PKIW3UMIMEN-101 1044854 - 32 www.bora.com...
-
Page 2: Table Of Contents
6.4.3 Automatic heat up function ..........26 4.2.1 Display and symbols ............10 Cleaning and maintenance 4.2.2 How induction cooktops work (PKFI3, PKI3, PKIW3) ..11 Safety devices ..............12 Cleaning agents .............27 4.3.1 Safety shut-down ............12 7.1.1 Cleaning products for glass ceramic cooktops ....27 4.3.2... -
Page 3: General Information
APAC Pty Ltd and BORA Lüftungstechnik GmbH – hereinafter Safety and warning instructions referred to as BORA – does not assume any liability for damage arising from disregard for or non-adherence to the documents The safety and warning instructions in this manual are included in the scope of delivery! emphasised with symbols and signal words. -
Page 4: Safety
Only use stove guards and covers that are BORA does not assume any liability for approved by the appliance manufacturer; damages caused by improper use or incorrect otherwise, there is a risk of accidents. -
Page 5: Safety Instructions For Installation
LS switch, fuses, automatic circuit appliances (particularly in the case of hard and breakers or contactor. sharp objects). Never use the appliances as work Contact BORA Service. or storage surfaces. Keep hard or sharp objects away from the WARNING! appliance surfaces. -
Page 6: Safety Instructions - Operation
Make sure that technical equipment is provided to enable all of the appliance’s poles to be disconnected from the mains with a contact opening width of at least 3 mm (LS switch and automatic circuit breakers, fuses, contactor). www.bora.com... -
Page 7: Safety Instructions - Cleaning And Maintenance
Only clean the cooktops when they have cooled down. WARNING! ÿ Risk of burns from hot steam Liquid between the cooking zone and the pan base can evaporate and cause burns. Make sure that the cooking zone and the pan base are always dry. www.bora.com... -
Page 8: Safety Instructions - Repairs, Servicing And Spare Parts
Work on electrical components must only be conducted by trained electrical personnel. Before disassembly, safely disconnect the appliance from the mains supply. www.bora.com... -
Page 9: Technical Data
3.0 kW 14,5 Fuse protection 1 x 16 A Dimensions (width x depth x height) 370 x 540 x 128 mm Fig. 3.3 PKIW3 appliance dimensions side view Weight (incl. accessories/packaging) 9.5 kg Cooktop BORA Professional 3.0 control Power levels 1–9, P knob dimensions... -
Page 10: Appliance Description
Cooktop appliance description 4.2.1 Display and symbols The power levels and cooking functions of each cooking zone are shown in the control knob display on the corresponding control knob. Fig. 4.2 Control knob operating elements Knob ring Touch surface www.bora.com... -
Page 11: How Induction Cooktops Work (Pkfi3, Pki3, Pkiw3)
210 mm Tab. 4.3 Induction cooking zone Minimum cookware diameter The BORA induction wok pan HIW1 is ideal for the induction 4.2.2 How induction cooktops work wok cooktop PKIW3 and is available as an accessory. (PKFI3, PKI3, PKIW3) Perform a magnet test if necessary. If a magnet sticks to the An induction coil is located underneath an induction cooking base of the utensils, they are normally induction compatible. -
Page 12: Safety Devices
Whilst the overheating protection is active, one of the following steps is taken: PKIW3: the activated power setting is switched back to the previous Power levels Safety shut-down after hours:minutes level;... -
Page 13: Installation
Make sure the delivery is complete and check it for damage. Minimum distance If there are any missing or damaged parts, please notify the BORA After Sales Service. Minimum clearance of 50 mm at the back from the worktop cut- Do not under any circumstances install parts which are out to the rear edge of the worktop. -
Page 14: Minimum Installation Dimensions (Standard Set-Up)
B O R A L Ü F T U N G S F I B E L 5.4.3 Worktop and kitchen units Create the worktop cut-out taking into account the specified cut-out dimensions. Make sure that the cut surfaces of the worktops are properly sealed. Comply with the instructions of the worktop manufacturer. www.bora.com... -
Page 15: Flush Installation
A in mm B in mm 1310 1338 1310 1681 1709 1681 Tab. 5.3 Cut-out dimensions of the appliance combinations in Tab. 5.2 Cut-out dimensions of the appliance combinations in the case of surface mounting the case of flush installation www.bora.com... -
Page 16: Installing The Control Knob In The Floor Unit Front Panel
Drilling pattern for 3 cooktops, 2 cooktop extractors Fixed front panel and 2 sockets Alternative installation with 1 control knob (only possible Boreholes for socket (x 2 external) on wok cooktop PKIW3) Bore holes for control knobs (x 8) Cooktop (x 3) Cooktop extractor (x 2) Worktop Fixed front panel ≥70... -
Page 17: Fitting The Control Knob
PKIW3 The plastic bar on the side of the cooktop extractor must only be removed when the wok cooktop PKIW3 is installed right next to the cooktop extractor. Fig. 5.15 Fitting the control knob Fig. -
Page 18: Installing The Cooktop
The plug for the mains supply cable must be accessible If applicable, insert the height adjustment plates [2]. following installation. If the mains supply cable has been damaged this must be replaced. The appliance components are linked by the ribbon cable provided. www.bora.com... -
Page 19: Connecting The Control Knobs
180° and the ports are on the front of the appliance Cooktop Rear cooking zone (zone 1) Front cooking zone (zone 2) Rear cooking zone control knob (zone 1) Front cooking zone control knob (zone 2) www.bora.com... -
Page 20: Establishing Contact Between The Cooktop Extractor And Cooktops
Special instructions for the wok cooktop PKIW3 companies. As the wok cooktop PKIW3 only has one cooking zone, The appliances may only be connected to the mains in the case of a connection with 2 control knobs it does power supply by certified specialists. -
Page 21: Basic Configuration
Affix the supplied nameplate to the back of these instructions. Provide the user with the accessories and all accompanying Detailed information on how to use the BORA documents, which are to be kept in a safe place. Professional 3.0 system can be found in the cooktop extractor’s operating instructions.. -
Page 22: Functions And Operation
Diagram of the touch commands Switching the appliances off Turn the knob ring anticlockwise to power level 0. Tap command diagram Long press diagram Any active additional functions will be deactivated and the appliance will be switched off. Extra-long press diagram www.bora.com... -
Page 23: Operating The Cooktops
Operating the cooktops 6.3.3 Cooktop power setting The full range of functions is only available for BORA Professional 3.0 system cooktops in combination with the corresponding cooktop extractors PKA3/PKA3AB and When the power setting is activated, maximum cooking zone PKAS3/PKAS3AB. -
Page 24: Variable Heat Retention Function
The temperatures can also vary due to the influence of the cooktop extractor. Fig. 6.11 Reducing the active heat retention level Deactivating the heat retention function Fig. 6.12 Deactivating the heat retention function www.bora.com... -
Page 25: Timer Function/Automatic Cut-Off
After 5 seconds the acoustic signal and the flashing display Fig. 6.14 are automatically deactivated. Turning the knob ring clockwise The flashing display and acoustic signal can be stopped early with a touch command on the control knob. If necessary, the residual heat indicator is then displayed. www.bora.com... -
Page 26: Automatic Heat Up Function
Activating the automatic heat up function An acoustic signal is heard, the automatic heat up function is activated and the corresponding timer counts down. The heat-up symbol and the set power level are shown in the control knob display (e.g. www.bora.com... -
Page 27: Cleaning And Maintenance
Never use a cooktop as a work or storage surface. Do not push or pull cookware over the cooktop. Always lift pots and pans. Keep the cooktop clean. Remove any dirt immediately. Only use suitable cookware on the appliance (see the Appliance description chapter). www.bora.com... -
Page 28: Cleaning The Control Knobs
7.4.2 Cleaning the touch surface and the knob housing Remove the knob ring. Clean the touch surface and the knob housing with a soft, damp cloth. Dry the touch surface and the knob housing carefully. Place the knob ring on the knob housing. www.bora.com... -
Page 29: Troubleshooting
Tab. 8.1 Resolving a fault Acknowledge the error by tapping the control knob. In all other cases, contact the BORA Service Team (see „10 Warranty, technical service, spare parts, accessories“) and enter the error number displayed and the appliance type. www.bora.com... -
Page 30: Decommissioning, Disassembly And Disposal
Never put your old appliance in domestic waste. Take the old appliance to a regional collection point for return and recycling electrical and electronic components and other materials. www.bora.com... -
Page 31: Warranty, Technical Service, Spare Parts, Accessories
The manufacturer’s warranty starts as soon as the BORA 10.2 Service product is handed over to the end customer by an authorised BORA dealer and is valid for 2 years. By registering on www. BORA Service: bora.com/registration the end customer has the possibility of extending the manufacturer’s warranty. - Page 32 Please accept our apologies in this eventuality. An updated version can be requested from the BORA Service Team. Subject to printing errors and mistakes. © BORA Vertriebs GmbH & Co KG All rights reserved.