Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nexo P15-TIS
Summary of Contents for Nexo P15-TIS
- Page 1 DP5546-02a-DI P15 / P15-TIS User manual...
-
Page 2: Table Of Contents
ARRAY EQ ____________________________________________________________________________ 15 MAINTENANCE ________________________________________________________________________ 16 TECHNICAL SPECIFICATIONS ___________________________________________________________ 18 USER NOTES _________________________________________________________________________ 19 EU Conformity declaration NEXO SA ZA DU PRE DE LA DAME JEANNE 60128 PLAILLY – France Declare under our sole responsibility that the product Loudspeaker... -
Page 3: Warnings
If the system seems to be malfunctioning or damaged, stop using it at once and have it repaired by a NEXO qualified technician. Do not expose the system directly to the sun or to the rain, do not immerse it into fluids, do not place objects filled with liquid on the system. -
Page 4: Equipment
EQUIPMENT EQUIPMENT 3 locations for rigging accessories, one at the back and one per side. WARNING: The depth of the M10 thread is 22mm (0.84 inch). On both sides, you’ll find a print for speaker stand. 3 locations for connecting, one at the back and one per side. Page 4 / 20... - Page 5 EQUIPMENT Pole stand assembly with pole stand or speaker stand Fix the pole stand on the connector plate (M20) of the Sub. Mount P15 on the pole stand/speaker stand (diameter of 35mm), IMPORTANT Speaker stand must be rated for P15 weight. Speaker stand must always be installed on a horizontal surface.
-
Page 6: Description
→ Amplification • The P15 speakers must be used with a NEXO processor to handle EQ, phase alignment, crossover and excursion/thermal protection for the system loudspeaker. There are two NEXO processor series supporting the P15 speakers: NXAMP (4 channels) amplified processors and DTD processors (stereo + sub). DTD processors ensure optimal performances when used with DTDAMP power amplifiers. -
Page 7: Preset
PRESET PRESET Please consult nexo-sa.com for NEXO TD Controllers firmware information. For the P15, the following setups are available: → MAIN is the recommended setup for most FOH application, similar to previous firmware setup. → MONITOR is recommended for monitor applications. Warning: this setup is a low latency setup and therefore its phase is not compatible with other NEXO cabinets, including subs. - Page 8 PRESET P15 + Sub Stage monitor applications with Subs (OMNI or CARDIO modes) Front of house applications with Subs (OMNI or CARDIO modes) Page 8 / 20...
-
Page 9: Hf Directivity
CROSSOVER FREQUENCY → 57 Hz: Full range application. → 85 Hz: Use as « front fill » on stage, complementing a main system. Use with a NEXO subwoofer, e.g. L18. → 120 Hz: Long throw application. Page 9 / 20... -
Page 10: Accessories
All P15 accessories are specifically rated in agreement with structural computations. Never use other accessories – including push-pins – when assembling P15 cabinets than the ones provided by NEXO: NEXO will decline responsibility over the entire P15 accessory range if any component is purchased from different supplier. - Page 11 ACCESSORIES VNU-PLADAPT (PNT-PLADAPT) Pole adapter, use with P15, HBRK600, VBRK15. Place VNU-PLADAPT, use only fasteners provided. Tight properly. Refer to the Product Data Sheet. PNU-VBRK15 (PNT-VBRK15) Vertical Cradle, use with CLADAPT, PLADAPT. Place VBRK15 on P15, use only fasteners provided. Tight properly.
- Page 12 ACCESSORIES VNT-LIFTADAPT (PNT-WMADAPT) Adapter, use with Truss Clamp, VNU-BUMP. Refer to the Product Data Sheet. VNI-WMADAPT (PNT-WMADAPT) Adapter, use with VNU-BUMP, VNI-WM380. Refer to the Product Data Sheet. Page 12 / 20...
- Page 13 ACCESSORIES PNI-P15TOL18 PNI-P15TOL2L18 P15 Under 1xL18 P15 Under 2xL18 (Omni or Cardio) Se référer à la fiche accessoire. VNI-CLADAPT (PNI-CLADAPT) Ceiling adapter, use with VNU-HBRK600, PNU-VBRK15. Screw CLADAPT to the ceiling (fasteners not provided). Place the assembly on CLADAPT, use the 2 guides.
- Page 14 ACCESSORIES VNI-WM380 (PNI-WM380) Wallmount for P15, use with WMADAPT. Mount the wall plate. Place the arm in the wall plate. Lock with the provided screw. Refer to the Product Data Sheet. PNU-P15FLGPS (PNT-P15FLGPS) HF Dispersion Horn ‘PS’ Remove the grille, remove the flange to place the PNU-P15FLGPS.
-
Page 15: Array Eq
ARRAY EQ ARRAY EQ The ArrayEQ allows to adjust the system frequency response in its lower range (see curves below, with different ArrayEq values): P15 60 60 rray ad usting Fre uency H P15 60 60 rray ad usting Fre uency H Page 15 / 20... -
Page 16: Maintenance
MAINTENANCE MAINTENANCE Driver access Remove 8 screws. P15- Unlock the 2 quarter-turn screws, Remove the grille. ( See above) Tightening torque: 3.5 Nm (Thread Locker: Loctite 242) Remove the 2 screws. Remove the stickers. Tightening torque: 2.5 Nm (Thread Locker: Loctite 222) To access to the HF diaphragm, remove 4 screws. - Page 17 Recone Kit 15” with screws 05HPC15R/K 05NHP15R/K HF diaphragm (with screws) 05CAPB01 HF cap black 05CAPB01-PW HF cap White 05SPK01 Speakon NL4 complete (with screws) NOTE: Speakers and Grills can be sent back to NEXO for recycling Page 17 / 20...
-
Page 18: Technical Specifications
Black or white structural paint P15: Magnelis® steel front grille + Back mesh Front finish P15-TIS: Black or white acoustic fabric fitted front Magnelis® steel grille Handle on both sides Threated inserts on the back and on both sides for connection of mounting... -
Page 19: User Notes
USER NOTES USER NOTES Page 19 / 20... - Page 20 Tel: +33 3 44 99 00 70 NEXO S.A. Fax: +33 3 44 99 00 30 E-mail: info@nexo.fr Parc d’activité de la Dame Jeanne nexo-sa.com F-60128 PLAILLY Page 20 / 20...
Need help?
Do you have a question about the P15-TIS and is the answer not in the manual?
Questions and answers