Advertisement

Quick Links

DP6422-01-DI
P18 / P18-TIS
User manual

Advertisement

Table of Contents
loading

Summary of Contents for Nexo P18-TIS

  • Page 1 DP6422-01-DI P18 / P18-TIS User manual...
  • Page 2: Table Of Contents

    ARRAY EQ ____________________________________________________________________________ 17 MAINTENANCE ________________________________________________________________________ 18 TECHNICAL SPECIFICATIONS ___________________________________________________________ 20 USER NOTES _________________________________________________________________________ 21 EU Conformity declaration NEXO SA ZA DU PRE DE LA DAME JEANNE 60128 PLAILLY – France Declare under our sole responsibility that the product Loudspeaker...
  • Page 3: Warnings

    Do not open the speaker, do not try to disassemble it neither to modify it in any way. The system doesn’t include any user-repairable part. If the system seems to be malfunctioning or damaged, stop using it at once and have it repaired by a NEXO qualified technician.
  • Page 4: Equipment

    EQUIPMENT EQUIPMENT 3 locations for rigging accessories, one at the back and one per side. WARNING: The depth of the M10 thread is 24mm (0.95 inch). On both sides, you’ll find a print for speaker stand. 3 locations for connecting, one at the back and one per side. Page 4 / 22...
  • Page 5 EQUIPMENT Pole stand assembly with pole stand or speaker stand Fix the pole stand on the connector plate (M20) of the Sub. Mount P18 on the pole stand/speaker stand (diameter of 35mm). It may take two to handle P18. IMPORTANT Speaker stand must be rated for P18 weight.
  • Page 6: Description

    → Amplification • The P18 speakers must be used with a NEXO processor to handle EQ, phase alignment, crossover and excursion/thermal protection for the system loudspeaker. There are two NEXO processor series supporting the P18 speakers: NXAMP (4 channels) amplified processors and DTD processors (stereo + sub). DTD processors ensure optimal performances when used with DTDAMP power amplifiers.
  • Page 7: Preset

    PRESET PRESET Please consult nexo-sa.com for NEXO TD Controllers firmware information. For the P18, the following setups are available: → MAIN is the recommended setup for most FOH application, similar to previous firmware setup. → MONITOR is recommended for monitor applications. Warning: this setup is a low latency setup and therefore its phase is not compatible with other NEXO cabinets, including subs.
  • Page 8 PRESET P18 + Sub Stage monitor applications with Subs (OMNI or CARDIO modes) Front of house applications with Subs (OMNI or CARDIO modes) Page 8 / 22...
  • Page 9: Hf Directivity

    CROSSOVER FREQUENCY → 50 Hz: Full range application. → 85 Hz: Use as « front fill » on stage, complementing a main system. Use with a NEXO subwoofer, e.g. L20. → 120 Hz: Long throw application. Page 9 / 22...
  • Page 10: Accessories

    All P18 accessories are specifically rated in agreement with structural computations. Never use other accessories – including push-pins – when assembling P18 cabinets than the ones provided by NEXO: NEXO will decline responsibility over the entire P18 accessory range if any component is purchased from different supplier.
  • Page 11 ACCESSORIES VNU-HBRK680 Horizontal Cradle, use with P18, CLADAPT, PLADAPT. Place HBRK680 on P18, use only fasteners provided. Tight properly. Refer to the Product Data Sheet. VNU-PLADAPT (PNT-PLADAPT) Pole adapter, use with P18, HBRK680, VBRK18. Place VNU-PLADAPT, use only fasteners provided. Tight properly.
  • Page 12 ACCESSORIES PNU-VBRK18 Vertical Cradle, use with CLADAPT, PLADAPT. Place VBRK18 on P18, use only fasteners provided. Tight properly. Refer to the Product Data Sheet. VNT-LIFTADAPT (PNT-WMADAPT) Adapter, use with Truss Clamp, VNU-BUMP. Refer to the Product Data Sheet. Page 12 / 22...
  • Page 13 ACCESSORIES VNI-WMADAPT (PNT-WMADAPT) Adapter, use with VNU-BUMP, VNI-WM450. Refer to the Product Data Sheet. PNI-P18TOL18 PNI-P18TOL2L18 P18 Under 1xL18 P18 Under 2xL18 (Omni or Cardio) Refer to the Product Data Sheet. Page 13 / 22...
  • Page 14 ACCESSORIES PNI-P18TOL20 PNI-P18TOL2L20 P18 Under 1xL20 P18 Under 2xL20 (Omni or Cardio) Refer to the Product Data Sheet. VNI-CLADAPT (PNI-CLADAPT) Ceiling adapter, use with VNU-HBRK680, PNU-VBRK18. Screw CLADAPT to the ceiling (fasteners not provided). Place the assembly on CLADAPT, use the 2 guides.
  • Page 15 ACCESSORIES VNI-WM450 Wallmount for P18, use with WMADAPT. Mount the wall plate. Place the arm in the wall plate. Lock with the provided screw. Refer to the Product Data Sheet. PNU-P18FLGPS HF Dispersion Horn ‘PS’ Remove the grille, remove the flange to place the PNU-P18FLGPS.
  • Page 16 ACCESSORIES PNT-2CASE18: FLIGHT CASE FOR 2X P18 PNT-ACC18: FLIGHT CASE FOR P18 ACCESSORIES PNT-COV18: COVER FOR P18 Page 16 / 22...
  • Page 17: Array Eq

    ARRAY EQ ARRAY EQ The ArrayEQ allows to adjust the system frequency response in its lower range (see curves below, with different ArrayEq values): P1 60x60 rray ad usting Fre uency H P1 60x60 rray ad usting Fre uency H Page 17 / 22...
  • Page 18: Maintenance

    MAINTENANCE MAINTENANCE Driver access Remove 8 screws. P18- Unlock the 2 quarter-turn screws, Remove the grille. ( See above) Tightening torque: 3.5 Nm (Thread Locker: Loctite 242) Remove the 2 screws. Remove the stickers. Tightening torque: 2.5 Nm (Thread Locker: Loctite 222) To access to the HF diaphragm, remove 4 screws.
  • Page 19 HPC18 RECONE KIT 05NHP18R/K HF DIAPHRAGM 4" - 8 Ohms with screws 05CAPB01 HF cap black 05CAPB01-PW HF cap White 05SPK01 Speakon NL4 complete (with screws) NOTE: Speakers and Grills can be sent back to NEXO for recycling Page 19 / 22...
  • Page 20: Technical Specifications

    Black or white structural paint P18: Magnelis® steel front grille + Back mesh Front finish P18-TIS: Black or white acoustic fabric fitted front Magnelis® steel grille Handle on both sides Threated inserts on the back and on both sides for connection of mounting...
  • Page 21: User Notes

    USER NOTES USER NOTES Page 21 / 22...
  • Page 22 Tel: +33 3 44 99 00 70 NEXO S.A. Fax: +33 3 44 99 00 30 E-mail: info@nexo.fr Parc d’activité de la Dame Jeanne nexo-sa.com F-60128 PLAILLY Page 22 / 22...

This manual is also suitable for:

P18

Table of Contents