Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nexo P12-I
Summary of Contents for Nexo P12-I
- Page 1 DP4603-02-DI P12-I User manual...
-
Page 2: Table Of Contents
ARRAY EQ ____________________________________________________________________________ 14 MAINTENANCE ________________________________________________________________________ 15 TECHNICAL SPECIFICATIONS ___________________________________________________________ 17 USER NOTES _________________________________________________________________________ 18 EU Conformity declaration NEXO SA ZA DU PRE DE LA DAME JEANNE 60128 PLAILLY – France Declare under our sole responsibility that the product Loudspeaker... -
Page 3: Warnings
If the system seems to be malfunctioning or damaged, stop using it at once and have it repaired by a NEXO qualified technician. Do not expose the system directly to the sun or to the rain, do not immerse it into fluids, do not place objects filled with liquid on the system. -
Page 4: Equipment
WARNING: The depth of the M10 thread is 13mm (0.5 inch). Assembly on distance rod or speaker stand Place distance rod on the connector plate (M20) of the Sub. Place PLADAPT on P12-I. Put the assembly on the distance rod / monitor stand (diameter of 35mm), IMPORTANT Speaker stand must be rated for P12 weight. -
Page 5: Description
→ Amplification • The P12 speakers must be used with a NEXO processor to handle EQ, phase alignment, crossover and excursion/thermal protection for the system loudspeaker. There are two NEXO processor series supporting the P12 speakers: NXAMP (4 channels) amplified processors and DTD processors (stereo + sub). DTD processors ensure optimal performances when used with DTDAMP power amplifiers. -
Page 6: Preset
PRESET PRESET Please consult nexo-sa.com for NEXO TD Controllers firmware information. For the P12, the following setups are available: → MAIN is the recommended setup for most FOH application, similar to previous firmware setup. → MONITOR is recommended for monitor applications. Warning: this setup is a low latency setup and therefore its phase is not compatible with other NEXO cabinets, including subs. - Page 7 PRESET P12 + Sub Stage monitor applications with Subs (OMNI or CARDIO modes) Front of house applications with Subs (OMNI or CARDIO modes) Page 7 / 20 P12-I...
-
Page 8: Hf Directivity
CROSSOVER FREQUENCY → 60 Hz: Full range application. → 85 Hz: Use as « front fill » on stage, complementing a main system. Use with a NEXO subwoofer, e.g. L15. → 120 Hz: Long throw application. Page 8 / 20... -
Page 9: Accessories
All P12 accessories are specifically rated in agreement with structural computations. Never use other accessories – including push-pins – when assembling P12 cabinets than the ones provided by NEXO: NEXO will decline responsibility over the entire P12 accessory range if any component is purchased from different supplier. - Page 10 Place VNU-PLADAPT, use only fasteners provided. Tight properly. Refer to the Product Data Sheet. PNU-VBRK12 (PNT-VBRK12) Vertical Cradle, use with CLADAPT, PLADAPT. Place VBRK12 on P12, use only fasteners provided. Tight properly. Refer to the Product Data Sheet. Page 10 / 20 P12-I...
- Page 11 Ceiling adapter, use with VNU-HBRK535, PNU-VBRK12. Screw CLADAPT to the ceiling (fasteners not provided). Place the assembly on CLADAPT, use the 2 guides. Tight with the fasteners provided with CLADAPT. Refer to the Product Data Sheet. Page 11 / 20 P12-I...
- Page 12 Refer to the Product Data Sheet. VNI-WM330 (PNI-WM330) Wallmount for P12, use with WMADAPT. Mount the wall plate. Place the arm in the wall plate. Lock with the provided screw. Refer to the Product Data Sheet. Page 12 / 20 P12-I...
- Page 13 PNU-P12FLG9040 (PNT-P12FLG9040) HF Dispersion Horn 90° - 40° Remove the grille, remove the flange to place the PNU-P12FLG9040. If it necessary, rotate it. Magnets keep the horn in place. Refer to the Product Data Sheet. Page 13 / 20 P12-I...
-
Page 14: Array Eq
ARRAY EQ ARRAY EQ The ArrayEQ allows to adjust the system frequency response in its lower range (see curves below, with different ArrayEq values): Page 14 / 20 P12-I... -
Page 15: Maintenance
Tightening torque: 3.5 Nm (Thread Locker: Loctite 242) Remove the 2 screws. Remove the stickers. Tightening torque: 2.5 Nm (Thread Locker: Loctite 222) To access to the HF diaphragm, remove 4 screws. Remove the horn. Tightening torque: 2 Nm Page 15 / 20 P12-I... - Page 16 Recone Kit 12” (with screws) 05HPC12R/K 05NHP12R/K HF diaphragm (with screws) 05P12UA-I Complete grille Instal Black (with fasteners) 05P12UA-IPW Complete grille Instal White (with fasteners) NOTE: Speakers and Grills can be sent back to NEXO for recycling Page 16 / 20 P12-I...
-
Page 17: Technical Specifications
TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS P12-I WITH NEXO ELECTRONICS Model P12-I 60 Hz – 20 kHz Frequency range (±6dB) Peak SPL Level (1m) 138dB Peak (Passive mode) / 140dB Peak (Active mode) Operating voltage 55Vrms (180Vpeak) HF dispersion 60°x60° - 90°x40° - Asymmetrical Dispersion 60° to 100°x40°... -
Page 18: User Notes
USER NOTES USER NOTES Page 18 / 20 P12-I... - Page 19 Page 19 / 20 P12-I...
- Page 20 Tel: +33 3 44 99 00 70 NEXO S.A. Fax: +33 3 44 99 00 30 E-mail: info@nexo.fr Parc d’activité de la Dame Jeanne nexo-sa.com F-60128 PLAILLY Page 20 / 20 P12-I...