Advertisement
Setting
Pr.
Name
range
0 to 6, 9 to 14,
Control method
20, 100 to 106,
800
selection
109 to 114
801
Output limit level
0 to 400%, 9999 9999
802
Pre-excitation selection 0, 1
Constant output range
803
torque characteristic
0 to 2, 10, 11
selection
Torque command
804
0 to 6
source selection
Torque command value
805
600 to 1400%
(RAM)
Torque command value
806
600 to 1400%
(RAM, EEPROM)
807
Speed limit selection
0 to 2
Forward rotation speed
808
0 to 400Hz
limit/speed limit
Reverse rotation speed
809
limit/reverse-side speed
0 to 400Hz, 9999
limit
Torque limit input
810
0 to 2
method selection
Set resolution
811
0, 1, 10, 11
switchover
Torque limit level
812
0 to 400%, 9999
(regeneration)
Torque limit level (3rd
813
quadrant)
Torque limit level (4th
814
quadrant)
815
Torque limit level 2
0 to 400%, 9999
Torque limit level during
816
acceleration
Torque limit level during
817
deceleration
Easy gain tuning
818
1 to 15
response level setting
Easy gain tuning
819
0 to 2
selection
820
Speed control P gain 1 0 to 1000%
Speed control integral
821
0 to 20s
time 1
822
Speed setting filter 1
0 to 5s, 9999
823
Speed detection filter 1 0 to 0.1s
Torque control P gain 1
824
(current loop
0 to 500%
proportional gain)
Torque control integral
825
time 1 (current loop
0 to 500ms
integral time)
826
Torque setting filter 1
0 to 5s, 9999
827
Torque detection filter 1 0 to 0.1s
Model speed control
828
0 to 1000%
gain
Number of machine end
829
0 to 4096, 9999 9999
encoder pulses
830
Speed control P gain 2 0 to 1000%, 9999 9999
Speed control integral
831
0 to 20s, 9999
time 2
832
Speed setting filter 2
0 to 5s, 9999
833
Speed detection filter 2 0 to 0.1s, 9999 9999
834
Torque control P gain 2 0 to 500%, 9999
Torque control integral
835
0 to 500ms, 9999 9999
time 2
836
Torque setting filter 2
0 to 5s, 9999
837
Torque detection filter 2 0 to 0.1s, 9999 9999
0 to 3, 24, 25,
840
Torque bias selection
9999
600 to 1400%,
841
Torque bias 1
9999
600 to 1400%,
842
Torque bias 2
9999
600 to 1400%,
843
Torque bias 3
9999
844
Torque bias filter
0 to 5s, 9999
Torque bias operation
845
0 to 5s, 9999
time
Torque bias balance
846
0 to 10V, 9999
compensation
Fall-time torque bias
847
0 to 400%, 9999
terminal 1 bias
Fall-time torque bias
848
0 to 400%, 9999
terminal 1 gain
Analog input offset
849
0 to 200%
adjustment
Brake operation
850
0 to 2
selection
Control terminal option-
851
Number of encoder
0 to 4096
pulses
Control terminal option-
852
Encoder rotation
0, 1, 100, 101
direction
853
Speed deviation time
0 to 100s
854
Excitation ratio
0 to 100%
Initial
Pr.
Name
value
Control terminal option-
20
Signal loss detection
855
enable/disable
selection
Terminal 4 function
0
858
assignment
0
Torque current/Rated
859
PM motor current
0
Second motor torque
1000%
860
current/Rated PM
motor current
1000%
Encoder option
0
862
selection
60/50Hz
Control terminal option-
863
Encoder pulse division
ratio
9999
864
Torque detection
865
Low speed detection
0
Torque monitoring
866
reference
0
867
AM output filter
Terminal 1 function
9999
868
assignment
869
Current output filter
9999
Speed detection
870
hysteresis
9999
Input phase loss
872
9999
protection selection
873
Speed limit
9999
874
OLT level setting
875
Fault definition
9999
876
Thermal protector input 0, 1
2
Speed feed forward
877
control/model adaptive
speed control selection
0
Speed feed forward
60%
878
filter
Speed feed forward
0.333s
879
torque limit
9999
880
Load inertia ratio
0.001s
Speed feed forward
881
gain
100%
Regeneration
882
avoidance operation
selection
5ms
Regeneration
883
avoidance operation
9999
level
0s
Regeneration
avoidance at
884
60%
deceleration detection
sensitivity
Regeneration avoidance
885
compensation frequency
limit value
Regeneration
9999
886
avoidance voltage gain 0 to 200%
9999
888
Free parameter 1
889
Free parameter 2
9999
Cumulative power
891
monitor digit shifted
times
892
Load factor
9999
Energy saving monitor
893
reference (motor
capacity)
9999
Control selection during
894
commercial power-
9999
supply operation
Power saving rate
9999
895
reference value
896
Power unit cost
9999
Power saving monitor
897
9999
average time
Power saving
9999
898
cumulative monitor
clear
9999
Operation time rate
899
(estimated value)
9999
C0
FM/CA terminal
(900)
calibration
9999
C1
AM terminal calibration ―
(901)
100%
C2
Terminal 2 frequency
(902)
setting bias frequency
0
C3
Terminal 2 frequency
(902)
setting bias
2048
125
Terminal 2 frequency
(903)
setting gain frequency
C4
Terminal 2 frequency
1
(903)
setting gain
C5
Terminal 4 frequency
1s
(904)
setting bias frequency
100%
C6
Terminal 4 frequency
(904)
setting bias
Setting
Initial
Pr.
range
value
126
Terminal 4 frequency
(905)
setting gain frequency
0, 1
0
C7
Terminal 4 frequency
(905)
setting gain
C12
Terminal 1 bias
0, 1, 4, 9999
0
(917)
frequency (speed)
0 to 500A,
C13
Terminal 1 bias (speed) 0 to 300%
9999
(917)
9999
0 to 3600A,
C14
Terminal 1 gain
9999
(918)
frequency (speed)
0 to 500A,
C15
9999
Terminal 1 gain (speed) 0 to 300%
(918)
9999
0 to 3600A,
Terminal 1 bias
9999
C16
command (torque/
(919)
magnetic flux)
0, 1
0
C17
Terminal 1 bias (torque/
(919)
magnetic flux)
1 to 32767
1
Terminal 1 gain
C18
command (torque/
(920)
0 to 400%
150%
magnetic flux)
0 to 590Hz
1.5Hz
C19
Terminal 1 gain (torque/
(920)
magnetic flux)
0 to 400%
150%
C8
Current output bias
(930)
0 to 5s
0.01s
signal
C9
0 to 6, 9999
0
Current output bias
(930)
current
0 to 5s
0.02s
C10
Current output gain
0 to 5Hz
0Hz
(931)
signal
0, 1
0
C11
Current output gain
(931)
current
0 to 400Hz
20Hz
0 to 400%
150%
Terminal 4 bias
C38
command (torque/
0, 1
0
(932)
magnetic flux)
1
C39
Terminal 4 bias (torque/
(932)
magnetic flux)
0 to 2
0
Terminal 4 gain
C40
command (torque/
(933)
magnetic flux)
0 to 1s
0s
C41
Terminal 4 gain (torque/
(933)
magnetic flux)
0 to 400%
150%
C42
PID display bias
0 to 200 times
7 times
(934)
coefficient
C43
PID display bias analog
0 to 1000%
0%
(934)
value
C44
PID display gain
0 to 2
0
(935)
coefficient
C45
PID display gain analog
(935)
value
DC380/
300 to 1200V
DC760V
Input voltage mode
977
selection
Parameter copy alarm
989
0 to 5
0
release
990
PU buzzer control
991
PU contrast adjustment 0 to 63
0 to 590Hz, 9999 6Hz
Operation panel setting
100%
992
dial push monitor
selection
0 to 9999
9999
0 to 9999
9999
994
Droop break point gain 0.1 to 100%, 9999
0 to 4, 9999
9999
Droop break point
995
torque
30 to 150%
100%
997
Fault initiation
Inverter
0.1 to 55kW
rated
PM parameter
0 to 3600kW
capacity
998
initialization
0 to 3
0
Automatic parameter
999
setting
1000
Direct setting selection 0 to 2
0, 1, 9999
9999
Lq tuning target current
1002
adjustment coefficient
0 to 500, 9999
9999
0, 1 to 1000h,
1003
Notch filter frequency
9999
9999
1004
Notch filter depth
1005
Notch filter width
0, 1, 10, 9999
9999
1006
Clock (year)
0 to 100%, 9999 9999
―
―
―
1007
Clock (month, day)
0 to 590Hz
0Hz
0 to 300%
0%
0 to 590Hz
60/50Hz
0 to 300%
100%
0 to 590Hz
0Hz
0 to 300%
20%
Setting
Initial
Name
range
value
0 to 590Hz
60/50Hz
0 to 300%
100%
0 to 590Hz
0Hz
0%
0 to 590Hz
60/50Hz
100%
0 to 400%
0%
0 to 300%
0%
0 to 400%
150%
0 to 300%
100%
0 to 100%
0%
0 to 100%
0%
0 to 100%
100%
0 to 100%
100%
0 to 400%
0%
0 to 300%
20%
0 to 400%
150%
0 to 300%
100%
0 to 500.00,
9999
9999
0 to 300%
20%
0 to 500.00,
9999
9999
0 to 300%
100%
0, 1
0
10
10
100
100
0, 1
1
58
0 to 3, 5 to 14,
17 to 20,
22 to 36,
38 to 46,
0
50 to 57, 61, 62,
64, 67, 71 to 75,
87 to 98, 100
9999
0.1 to 100%
100%
0 to 255, 9999
9999
0, 3003, 3103,
8009, 8109,
0
9009, 9109
1, 2,10 to 13,
9999
20, 21, 9999
0
50 to 150%,
9999
9999
0, 8 to 1250Hz
0
0 to 3
0
0 to 3
0
2000 to 2099
2000
101 to 131,
201 to 229,
301 to 331,
401 to 430,
501 to 531,
601 to 630,
101
701 to 731,
801 to 831,
901 to 930,
1001 to 1031,
1101 to 1130,
1201 to 1231
17
PARAMETER LIST
Advertisement
