Table of Contents
Advertisement
Quick Links
Manual Super Power Series 125HYD
INSTALLATION
THIS MANUAL MUST BE KEPT ON BOARD AT ALL TIMES
Hydraulic Tunnel Thruster
Series 125 HYD
With Electronic Controller
Serial N° : ----------------------------------------------------
Date of Installation : ----------------------------------------
Via Philips 5, 20900 Monza (MI), Italy
Tel. +39 039 200 1973-936 - Fax +39 039 2004299
www.max-power.com
OPERATION
E-mail:contact@max-power.com
Last Update: December 2013
MAINTENANCE
0
Advertisement
Table of Contents
Related Manuals for MAX power 125 HYD Series
Summary of Contents for MAX power 125 HYD Series
- Page 1 Manual Super Power Series 125HYD Last Update: December 2013 Hydraulic Tunnel Thruster Series 125 HYD With Electronic Controller INSTALLATION OPERATION MAINTENANCE Serial N° : ---------------------------------------------------- Date of Installation : ---------------------------------------- THIS MANUAL MUST BE KEPT ON BOARD AT ALL TIMES Via Philips 5, 20900 Monza (MI), Italy Tel.
-
Page 2: Table Of Contents
Manual Super Power Series 125HYD Last Update: December 2013 To ensure a proper installation, correct usage and long-lasting enjoyment of this equipment, please take time to read this manual thoroughly. Table of Contents Number Description Page General Installation Guidlines Tunnel Propeller Drive Leg &... -
Page 3: General Installation Guidlines
Manual Super Power Series 125HYD Last Update: December 2013 GENERAL INSTALLATION GUIDLINES Decide on the best location for the SUPER POWER. (See drawing: “Positioning & Measurements” at back of manual) The tunnel must be as low as possible and as far forward as possible. The propellers must not protrude beyond the hull line. -
Page 4: Propeller Drive Leg & Motor Support
Manual Super Power Series 125HYD Last Update: December 2013 CAUTION: Do not fibre glass the area of the motor support. It is recommended to lightly sand down the area where the motor support is fitted. On the outside, when the ISOPHTALIQUE RESIN has set, finish with an application of resin and material, followed with an additional coat on the hull, in the tunnel area. -
Page 5: The Hydraulic Motor And Its Adapter
Manual Super Power Series 125HYD Last Update: December 2013 THE HYDRAULIC MOTOR AND ITS ADAPTER Do not separate the motor from its adapter. Insert the lower metal coupling on the greased leg shaft. Fit the flexible coupling, then the motor and its adapter, tighten the screws (∅ 10mm) to a torque of 40 Nm. -
Page 6: Hydraulic Specifications
Manual Super Power Series 125HYD Last Update: December 2013 The pump can be driven by either an internal combustion engine (crankshaft pulley or gearbox PTO) or an electric motor. Depending on the speed and choice of drive, but should always comply with the rated pressure/flow of the thruster. For an internal combustion engine with fixed or variable speed, 3 types of pumps can be used, depending on the unit to be fitted: Direct PTO:... -
Page 7: Hydraulic Custom Pack
M10 = 5/8’’ M12 = 3/4’’ M16 = 1’’ INTAKE DIAMETERS of standard hydraulic elements MAX POWER: 1 / 2 / 11 = Female BSP 3/4'' 3 / 6 / 7 / 8 / 9 = Female BSP 1/2'', 4 / 5 = Female BSP 3/8''... -
Page 8: Maintenance
Manual Super Power Series 125HYD Last Update: December 2013 MAINTENANCE In order to ensure peak performance from your SUPER POWER, the tunnel, the leg and the propellers must be kept clean. IMPORTANT: In order to prevent chalky deposits, which cause damage to the oil seals, we recommend cleaning the shaft and the oil seals first, then applying a layer of silicon oil before assembling the propellers. - Page 9 Manual Super Power Series 125HYD Last Update: December 2013 Installation Notes...
-
Page 10: Spare Parts List
Manual Super Power Series 125HYD Last Update: December 2013 SPARE PARTS LIST SP 125 HYD N° DESCRIPTION Composite Leg Classic Leg REFERENCES MPHYC800 MPHY0800 Motor fixing bolts MPOP 5240 Hydraulic motor MPHY 6010 Adapter plate MPHY 5012 Upper shaft coupling Hydraulic type MP205027 10 Rubber coupling MP205023... - Page 11 Manual Super Power Series 125HYD Last Update: December 2013 SUPER POWER 125 HYD MAX POWER...
- Page 12 Manual Super Power Series 125HYD Last Update: December 2013 HEAT RLYS...
- Page 13 Manual Super Power Series 125HYD Last Update: December 2013 HEAT RLYS...
- Page 14 Manual Super Power Series 125HYD Last Update: December 2013...
-
Page 15: Positioning And Measurements
Manual Super Power Series 125HYD Last Update: December 2013 Super Power Hydraulic: Positioning and Measurements Model Dim (mm) E Ideal E Mini Weight 9 Kg 12 Kg 20 Kg... -
Page 16: Warranty Document (To Be Returned)
The warranty as outlined above is only applicable to Max Power manufactured thrusters and optional equipment as used in marine pleasure industry. The supplier holds the exclusive right to test the product and...