Maytag MLE24PDAYW Installation Instructions Manual page 17

Pricing
After the door is opened following the completion of a cycle, the
display indicates the cycle price (unless set for free operation). As
coins or debit inputs arrive, the display will change to lead the user
through the initiation of a cycle.
There are four (4) types of pricing:
Fixed "Vend" Pricing
A dryer set up for "Fixed Cycle" operation can only accept
additional time accumulated by increments equal to the length of a
complete dry cycle. A maximum of 99 minutes may be purchased;
no additional credit is given when 99 minutes is in the display.
Accumulator Pricing
If the price is set to one coin 1, then accumulator mode is in effect
(stacked PD models also require Fixed Cycle with Top Off option to
be selected). Cycle time can be purchased one coin at a time (PD
models) up to the maximum time of 99 minutes. Stacked PD dryers
will credit all money to a cycle with a single button press while in
accumulator pricing.
Fixed Cycle With Top Off Pricing
A dryer set to offer "Top Off" capability will allow time to be
added to an existing dry cycle in increments equal to the number
of minutes of dry time per quarter (coin 1), up to 99 minutes,
regardless of the cost required to start the dryer. No credit is given
for coins or debit inputs entered when the control is displaying 99
minutes.
PR Models: In Enhanced Debit Mode, the top off price can be set
independently. (See VALUE OF COIN 2), and the top off time is
calculated according to the following equation:
top off price
=
full cycle price
Penny increment offset is not applied to top off purchases.
Free Cycles
This is established by setting the cycle price to zero. When this
happens, "SELECT CYCLE" will appear rather than a cycle price.
Any cycle started as a free cycle will automatically terminate when
the door is opened.
Debit Card Ready
This appliance is debit card "cable" ready. It will accept a variety of
debit card systems, but does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper dryer control
set-up. In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
CONTROL SET-UP PROCEDURES
IMPORTANT: Read all instructions before operating.
The fabric setting key pads along with the digital display are used to
set up the dryer controls.
The display can contain 4 numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related code
values available for use in programming the appliance.
How to use the key pads to program the controls
1. The WHITES AND COLORS key pad is used to adjust the
values associated with set-up codes. Pressing the key pad will
increment the value by one (1). Rapid adjustment is possible by
holding the key pad down.
2. The PERM. PRESS key pad will advance you through the
set-up codes. Pressing the key pad will advance you to the
next available set-up code. Holding the key pad down will
automatically advance through the set-up codes at a rate
of one (1) per second.
3. The DELICATES key pad is used to select or deselect options.
top off time
full cycle length
DISPLAY
After the dryer has been installed and plugged in, the display will
show "0 minutes."
Stacked PR Models
PRICE
Once the unit has been plugged in and the dryer door opened and
closed, the display will show the price. In PR and PN models set for
free cycles, the display will flash "SELECT CYCLE" (not shown).
Stacked PD Models
PRICE
PRICE
PRICE
IMPORTANT: The console must not be opened unless power is
PRICE
first removed from the dryer. To access connector AA1:
g Unplug dryer or disconnect power.
g Open console, disconnect plug on AA1, close console.
PRICE
g Plug in dryer or reconnect power.
Stacked PD Models: Insert access panel key and turn
n
counterclockwise.
Stacked PR Models: Once the debit card reader is installed
n
(according to the reader manufacturer's instructions), the
set-up mode can be entered by inserting a manual set-up card
(supplied by the reader manufacturer) into the card slot.
If manual set-up card is not available, manual set-up mode can be
entered by turning the access panel key.
The dryer is now in the set-up mode.
NOTE: It is not necessary to set up the dryer with the following
codes; the dryer is pre-set at the factory. These codes can be
used to change settings, if desired.
PD units are pre-set at the factory for fixed cycle price with
n
top off.
PR units are pre-set for free cycle operation so they can
n
be run without readers or coins.
17 17