Table of Contents
Advertisement
If you enable the WLS Key Does Not Use Access Codes
option, the disarm button will work on wireless keys which
have not been assigned access codes. Wireless keys can
only be assigned access codes when used with PC5132 v3.0
or higher or with PC5102 1.0 and higher.
To prevent disarming by wireless keys which don't have
access codes, disable this option. (Please see your PC5102/
PC5132 Installation Manual for more information on program-
ming wireless keys.)
NOTE: This option must be enabled when using a PC5132
v2.1 or earlier.
Quick Arm Enable . . . . . . . . . . . . . . . . . . . Section [015]: [4]
Quick Exit Enable . . . . . . . . . . . . . . . . . . . . Section [015]: [3]
Arm/Disarm Bell Squawk . . . . . . . . . . . . . . Section [014]: [1]
Squawk on Away Arm/Disarm Only . . . . . . Section [017]: [8]
Closing Confirmation . . . . . . . . . . . . . . . . . Section [381]: [4]
Opening After Alarm Keypad Ringback . . Section [381]: [1]
Opening After Alarm Bell Ringback . . . . . . Section [381]: [2]
Bypass Status Displayed While Armed . . . Section [016]: [7]
Unident. Wkey Disarm Enabled . . . . . . . . . Section [017]: [1]
5.18 Entry/Exit Delay Options
Two different Entry Delays can be programmed: the first entry
delay will be enabled for Delay 1 type zones and the second for
Delay 2 type zones. Only one Exit Delay can be programmed.
NOTE: When the panel is armed, the entry delay will follow the
entry delay time programmed for the delay zone which is vio-
lated first.
NOTE: For UL Listed products, exit delay must not exceed 60
seconds.
Users can restart the exit delay by pressing the Away key
while it is counting down. The system will not log the user who
re-started the exit delay, unless the Quick Arming Disabled/
Function Keys Require Code option is turned on (Section
[015], Option [4]).
NOTE: If the system has been Stay armed or armed with no
entry delay ([*][9]) pressing the Away key will not start an exit
delay.
Upon arming, the panel will begin the exit delay. If the Audible
Exit Delay with Urgency option is enabled, the keypad will
beep at one second intervals until the exit delay expires. The
keypad will beep rapidly for the last 10 seconds of exit delay
to warn the user that the system is about to arm. If this option
is disabled, the keypad will not beep during the exit delay.
The Audible Exit Fault, as explained in Section 3.1, will notify
the user if they failed to secure the premises upon arming.
This option can be enabled or disabled according to the
user's needs.
For commercial applications, the Bell Squawk on Exit Delay
option may be enabled. The panel will squawk the alarm out-
put once every second when the exit delay is initiated and
three times per second for the last 10 seconds until the exit
delay expires.
Upon entry, if a Delay zone is violated, the panel will begin the
entry delay. The keypad will emit a steady tone. The keypad
will pulse the keypad sounder during the last 10 seconds to
warn the user the system is about to go into alarm. If there was
an alarm during the armed period, the keypad will pulse for
the entire entry delay to warn the user of the previous alarm.
For commercial applications Bell Squawk on Entry Delay
may be enabled. The panel will squawk the alarm output once
P r o g r a m
D e s c r i p t i o n s :
5 . 1 8
E n t r y / E x i t
every second until the entry delay expires or the system is dis-
armed.
If the Bell Squawk During Auto-Arm option is enabled, the
bell will squawk once every 10 seconds for one minute during
the Auto-arm pre-alert. This will notify anyone on the premises
that the system is being armed.
If the Exit Delay Termination option is enabled, the panel will
monitor the Delay 1 zones during exit delay. During the exit
delay, if a Delay 1 zone is violated and then secured, the exit
delay will be terminated and the panel will be armed immedi-
ately.
Entry Delay 1 and 2 (System Times) . . . . . . . . . Section [005]
Exit Delay (System Times) . . . . . . . . . . . . . . . . . Section [005]
Audible Exit Delay with Urgency . . . . . . . . .Section [014]: [6]
Audible Exit Fault Enabled/ Disabled . . . . .Section [013]: [6]
Bell Squawk Options . . . . . . . . . . . . . . Section [014]: [2] - [4]
Exit Delay Termination . . . . . . . . . . . . . . . . .Section [014]: [7]
5.19 Swinger Shutdown
The swinger shutdown feature is designed to prevent a "run-
away" communicator from tying up the central station. After
the panel has communicated the programmed number of
transmissions for an event, it will no longer report that event
until the swinger shutdown is reset. Different swinger shut-
down levels can be set for zone alarms, zone tampers and
maintenance signals.
By default, each Swinger Shutdown limit is set to [003]. The
panel will not send more than three signals for each zone until
the swinger shutdown is reset.
The bell output will not be activated for alarms on zones that
have exceeded the limit of alarms set in the swinger shutdown
counter.
Swinger shutdown will be reset every day at midnight or when
the panel is armed. Once reset, the panel will again communi-
cate normally.
Swinger Shutdown . . . . . . . . . . . . . . . . . . . . . . . Section [370]
5.20 Event Buffer
The panel will store the last 128 events which occurred on the
system. The Event Buffer will contain the name, time and
date of each event, along with the zone number, access code
number or any other information pertaining to the event.
If the Event Buffer Follows Swinger Shutdown option is
enabled, the event buffer will not store events after the
swinger shutdown limit has been reached. This will prevent
the panel from overwriting the entire buffer if a problem exists.
The event buffer can be viewed in three different ways: from
an LCD keypad (see "[*][6] User Functions" ), printed on-site
using the PC5400 printer module, or it can be uploaded using
DLS software.
Event Buffer Follows
Swinger Shutdown . . . . . . . . . . . . . . . . . . . .Section [013]: [7]
5.21 Keypad Lockout Options
The panel can be programmed to "lock out" keypads if a
series of incorrect access codes is entered. Once the Num-
ber of Invalid Codes Before Lockout limit has been reached,
the panel will lock out all keypads for the Lockout Duration
and log the event to the event buffer. For the duration of the
lockout, the panel will sound an error tone when any key is
pressed.
D e l a y
O p t i o n s
25
Advertisement
Table of Contents
