Do you have a question about the PC1555MX and is the answer not in the manual?
Questions and answers
Emily
May 23, 2025
Don't know codes but power went out two beeps keep going off
1 comments:
Mr. Anderson
May 25, 2025
After a power outage, the DSC PC1555MX alarm system uses beeping codes to indicate system status. If the [A] key is held for two seconds, the panel beeps three times to confirm activation. When communication to the central station is successful (kissoff received), the keypad beeps ten times rapidly. Arming is not allowed if there is an AC or battery trouble condition.
This answer is automatically generated
Nancy
February 10, 2025
Our alarm battery died and the alarms are chirping. I replaced the battery and they are still chirping. How do I reset to stop the noise.
Control box PC1555MX. Pad PC823
1 comments:
Mr. Anderson
February 11, 2025
To reset the DSC PC1555MX alarm system after replacing the battery, follow these steps:
1. Press [✱] to enter the function list. 2. Scroll to find "Output Control." 3. Select "Command Output #1" by using the arrow keys and pressing [✱]. 4. If the smoke detector was triggered, reset it by pressing [✱][7][2] on an LED or Fixed Message LCD5501Z keypad.
If the chirping continues, check for any remaining trouble conditions and clear them accordingly.
The warranty for international customers is the same as for any tentional such as masking, painting, or spraying of any material on the lenses, such a jurisdiction apply to any claim by or against DSC, the limitations This system contains security features which were known to be effective at...
IC, before the registration number signifies that registration was performed based on a Your security system is made up of a DSC control panel, one or more keypads and various sensors 2001, the REN for this product is part of the product identifier that has the format Declaration of Conformity indicating that Industry Canada technical specifications were met.
Fire Escape Planning System Information There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a family escape plan be developed and rehearsed. Fill out the following information for future reference and store this manual in a safe place. 1.
To activate the door chime from an LCD Keypad: ___________________________________________ _____________________________________ Press [ ] to enter the function list, then scroll to find... Press [ ] or [4] to enable or disable the Door Chime feature. Press [#] to return to the ___________________________________________ _____________________________________ Press (*) For<>...
Access Codes Testing Your System Access codes are used to arm and disarm the system. There are 37 access codes available: 1 master Alarm Test code, 32 regular access codes, 2 duress codes and 2 supervision codes. Ask your installer for more The Alarm Test provides two-second tests of the keypad sounder and bell or siren.
To view troubles from an LED or Fixed Message LCD5501Z keypad: Alternate Arming Methods A trouble will be indicated by the Trouble light/message, which will remain ON until the trouble condition Away Arming is cleared. If you cannot determine the cause of the trouble condition, contact your installer for assistance. Arming the system in the Away mode will have all interior zones and perimeter zones active.
Disarming the System Zone Bypassing Disarming from an LED or Fixed Message LCD5501Z keypad: The zone bypassing function is used when access is needed to part of the protected area while the system is armed. Zones that are temporarily out of service due to damaged wiring or contacts may be Enter the premises through a designated Exit/Entry door.
Continued from page 7 ... Programming codes from an LCD Keypad: If an Alarm Sounds Master Code Fire Alarm Press the [ ] key to enter the function list. Scroll (< >) to... If your system has been installed with fire detectors and the alarm sounds in a pulsing mode, follow Press (*) for <>...
Page 10
PC1555RKZ LED Keypad PC5508Z LED Keypad LCD5501Z Fixed Message Keypad LCD5500Z Keypad System Light (PC1555RKZOnly): If the System light is ON, one or more of these conditions could be present on the system: System Busy System Troubles (see 'Viewing Trouble Conditions' on page 11). Alarm Memory (see 'Disarming the System' on page 6).
Need help?
Do you have a question about the PC1555MX and is the answer not in the manual?
Questions and answers
Don't know codes but power went out two beeps keep going off
After a power outage, the DSC PC1555MX alarm system uses beeping codes to indicate system status. If the [A] key is held for two seconds, the panel beeps three times to confirm activation. When communication to the central station is successful (kissoff received), the keypad beeps ten times rapidly. Arming is not allowed if there is an AC or battery trouble condition.
This answer is automatically generated
Our alarm battery died and the alarms are chirping. I replaced the battery and they are still chirping. How do I reset to stop the noise. Control box PC1555MX. Pad PC823
To reset the DSC PC1555MX alarm system after replacing the battery, follow these steps:
1. Press [✱] to enter the function list.
2. Scroll to find "Output Control."
3. Select "Command Output #1" by using the arrow keys and pressing [✱].
4. If the smoke detector was triggered, reset it by pressing [✱][7][2] on an LED or Fixed Message LCD5501Z keypad.
If the chirping continues, check for any remaining trouble conditions and clear them accordingly.
This answer is automatically generated