hold & serve drawer drawers or reaching into the appliance, as Please read this entire use & care manual heated vapor can quickly cause burns. before operating your CVap hold & serve ® drawer. The manual contains important safety information and operating instructions. Contamination Hazard As is the case with many kitchen Can cause serious illness or damage to...
hold & serve drawer carrier should agree to inspect the damage receiving your appliance within 15 days. Please retain all packing materials. The carrier will supply an Shipping Damage inspection report and the required claim Examine equipment thoroughly for shipping forms.
hold & serve drawer electrical necessary for a licensed electrician to install the correct outlet or wiring. Winston does not recommend wiring the appliance direct. The appliance is shipped from the factory with a 84" (213cm) minimum power cord and Below is electrical information for various plug.
hold & serve drawer component identification 7. Drawer Gasket seals food chamber 1. Drawer(s) 6" (152mm) deep for holding against heat or vapor loss. one full size, two half size, or three third size pans. 8. Evaporator (not visible in photo) located inside the base, supplies vapor to food 2.
hold & serve drawer controls Some details have been omitted for clarity. the food temp setting will provide a moist 1. Power Switch controls electrical power to texture. Elevating the texture setting will the appliance. deliver a progressively drier and crisper texture.
hold & serve drawer concentrated proteins and salts to deposit in daily operating procedures the evaporators, potentially causing corrosion. This can void your warranty. The HBK controller allows you to set a single food temperature and texture for the entire Contamination Hazard appliance.
Page 9
hold & serve drawer hbk programming NOTES COMPUTER DISPLAY PRESS KEY/ACTION Press and hold the #1 key STEP 1 while turning on the power POWER switch. IMMEDIATELY SWITCH RELEASE #1 KEY after turning on the power. The first two digits of the display will flash, indicating you are in the programming mode.
hold & serve drawer NOTES COMPUTER DISPLAY PRESS KEY/ACTION Use arrow keys to adjust the STEP 7 Food Texture setting. Hold either key down for fast scrolling (0 to 210˚F (32 to 99ºC)). 300˚F (149ºC) maximum when added to Food Temp setting.
hold & serve drawer daily cleaning Required Cleaning Accessories & Supplies • Pan for draining evaporator • Food grade germicidal detergent Corrosion Hazard • Descaling agent (ScaleKleen™) Can cause damage to appliance. (available through Winston Customer Clean appliance daily to avoid potential corrosion Service 1-800-234-5286) damage.
Page 13
hold & serve drawer 6. Wipe down all outside surfaces with mild daily cleaning procedure detergent, in particular where the drawer seals. Also clean the gasket. This procedure will prolong gasket life. Burn Hazard Can cause injury. Leaking Hazard Allow 30 minutes for appliance to cool before Can cause damage to appliance.
Page 14
hold & serve drawer 8. Inspect heating elements (if exposed). The elements are stainless steel. If cleaning is needed, scrub with Teflon ™ nylon bristle brush to remove heavy food particles. Further cleaning may be done with a plastic scouring pad and alkaline based cleansers.
If the problem you're experiencing from the factory online. isn't listed, or if the standard solution fails to Visit www.winstonind.com Please have the following information on hand when contacting Winston Industries regarding product service. 1. Model _____________________Serial # _____________________________________ (located on name plate) 2.
Page 16
hold & serve drawer troubleshooting TROUBLE FAULT CODE Digital display fails to light ................A Digital display reading inconsistently ............... J Flooding/leaking water ..................C, H, I Food drying out ....................B, E, F, H Food excessively moist ..................D, G Food not hot enough ..................
Page 17
hold & serve drawer 2. Use nut driver and open-end wrench to troubleshooting remove drawer rollers and replace with new components. How to Tell if Unit is Working Properly 3. Tighten roller bolts with open-end wrench 1. Preheat unit for 30 minutes. and nut driver.
Page 18
hold & serve drawer This appliance utilizes high voltage troubleshooting electrical systems, high temperature heating systems, and hot water vapor. If used improperly, any of these hazards are capable of causing serious injury or death. To avoid the potential for an Electrical Hazard accident, please have appliance installed Can cause serious injury or death.
PURPOSE AND ANY IMPLIED WARRANTY OF MERCHANTABILITY. Ask us for a complete warranty disclosure or go to: www.winstonind.com/documents/4272V089_zap_warranty_agreement.pdf. Terms and Conditions of Sale for Winston Industries’ products are available here: www.winstonind.com/documents/4272X833_terms_and_conditions_of_sale.pdf. Both the Warranty and Terms and Conditions of Sale are integral to this document.
Need help?
Do you have a question about the cvap PS2198 and is the answer not in the manual?
Questions and answers