Related Manuals for Pace 5050-0552
Summary of Contents for Pace 5050-0552
- Page 1 Operation and Maintenance Manual for the ® PACE MBT 350 Digital Soldering/Desoldering System P/N 5050-0552 Rev. A –TWF05-05...
-
Page 2: Table Of Contents
Temperature Adjust Mode ..............15 Setting Channel Offset................15 Accessing Calibration Menu ...............15 Hello Message ..................16 Corrective Maintenance ..............16 Packing List..................17 Spare Parts ..................17 Service ....................17 LIMITED WARRANTY STATEMENT ..........18 Contact Information................19 ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 2 of 19... -
Page 3: General Information
General Information Introduction Thank you for purchasing the PACE model MBT 350 Soldering/Desoldering System. This manual will provide you with the information necessary to properly set up, operate and maintain the MBT 350. Please read this manual thoroughly before using the unit. The MBT 350 system is designed for the most demanding soldering applications. -
Page 4: Eos/Esd
EOS/ESD Tip-To-Ground Resistance: Less than 5 ohms. AC Leakage: Less than 2 millivolts RMS from 50Hz to 500Hz ENVIRONMENTAL REQUIREMENTS Ambient Operating Temperature: 0°C to 50°C (32°F to 120°F) Storage Temperature: -40°C to 100°C (-40°F to 212°F) Capabilities All capabilities are dependent upon the use of the appropriate Functional Accessories or Work Aids (refer to Basic Operation section). -
Page 5: Parts Identification
MBT system to handpiece connected to Channel 2 (CH 2). CH 3 POWER RECEPTACLE - Provides power, tip ground, sensing circuitry and finger switch connection from MBT system to handpiece connected to Channel 3 (CH 3). ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 5 of 19... - Page 6 15. FUSE - Provides overload protection for system. 16. FOOT PEDAL RECEPTACLE - Input for Foot Pedal (optional), which activates vacuum or pressure to the air-operated handpieces. ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 6 of 19...
-
Page 7: Safety Guidelines
If you require assistance in the use of this product, contact your local authorized PACE dealer or PACE directly as shown on page 15 of this manual Safety Guidelines The following are safety precautions that personnel must understand and follow when using or servicing this product. -
Page 8: Safety
Safety PACE adheres to the following Heading Guidelines (based on OSHA guidelines) when listing special information or precautions to be taken. Especially important are all procedures and practices which, if not strictly observed, could result in injury or loss of life. These "NOTES", "CAUTIONS","WARNINGS" and "DANGERS"... -
Page 9: Servicing Precautions
2. Always use this system in a well-ventilated area. A fume extraction system such as those available from PACE are highly recommended to protect personnel from solder flux fumes. 5. Exercise proper precautions when using chemicals (e.g., solder paste). Refer to the Material Safety Data Sheet (MSDS) supplied with each chemical and adhere to all safety precautions recommended by the manufacturer. - Page 10 AC power Figure 3b outlet. The system is now ready for operation. 10. Read the "OPERATION" section of this manual thoroughly before operating the system. ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 10 of 19...
-
Page 11: Attaching Tip & Tool Stand
Never remove a heated tip using bare hands. Use the Hot Grip Rubber Pad or Tip Tool. Never use a wrench or pliers when removing a handpiece tips. ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 11 of 19... -
Page 12: Definitions
2. Plug the prong end (male end) of the power cord into an appropriate 3 wire grounded AC supply receptacle. CAUTION To insure operator and ESD/EOS safety, the AC power supply receptacle must be checked for proper grounding before initial operation. ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 12 of 19... -
Page 13: Led Operation
Press the PROGRAM Key to keep the stored default Temperature Scale. b) Press and release the UP Key to change the default Temperature Scale. Press and release the PROGRAM Key to move to the next step. ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 13 of 19... -
Page 14: Set Upper Limit
MBT 350 scans each channel and display it’s information individually for 3 seconds than continually repeats the order. Press and release the PROGRAM Key to move to the next step. ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 14 of 19... -
Page 15: Set Lcd Contrast
7. Press the PROGRAM Key to save calibration and move to the next channel. Upon exiting, LED will illuminate green and the display will return to normal operation mode. ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 15 of 19... -
Page 16: Hello Message
Vacuum Cup will not hold Worn or broken Replace vacuum cup component vacuum cup Vacuum Pickup Rod binding Vacuum Pickup rod is Contact PACE for assistance bent ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 16 of 19... -
Page 17: Packing List
Fuse, 2.0 A, 125 V, Lag Time (MBT 350) 1159-0275-02-P5 Fuse, 1.25 A, 230 V, Lag Time (MBT 350E) 1159-0275-01-P5 Service Please contact PACE or your local distributor for service and repair. ©2005 PACE Inc., Annapolis Junction, Maryland All Rights Reserved Page 17 of 19... -
Page 18: Limited Warranty Statement
PACE Incorporated retains the right to make changes to specifications contained herein at any time, without notice. Contact your local authorized PACE Distributor or PACE Incorporated to obtain the latest specifications. The following are trademarks and/or service marks of PACE, Incorporated, MD, USA: ™...