Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PR Lighting LS 90 Logo
Summary of Contents for PR Lighting LS 90 Logo
- Page 1 LS 90 Logo PR-6830 The user manual contains important information about the safe installation and use of a projector. Please read and follow these instructions carefully and keep the manual in a safe place for future reference. PR LIGHTING LTD.
-
Page 2: Table Of Contents
Any future technical change in the user manual won’t be with any further notice. Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from the delivery date but the light source is not within the warranty. - Page 3 NOTE Before a projector’s installation, power-on, operation and maintenance, please carefully read the safety information hereinafter! The following safety signs are used in the user manual. User Electrical Protective High Warning Flames Goggles Manual shock Gloves Temperature ● When unpacking , check if there is transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use it.
-
Page 4: Cleaning And Maintenance
●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from power mains. ●Under normal temperature, the temperature of the housing will be 55℃; after being stable, the unit’s ℃ surface temperature will be ●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not mean the projector has some defects. -
Page 5: Installation
灯体 吊臂 灯体 body 吊臂 arm 4. INSTALLATION 吊臂 保险绳 警告 为确保 安全，请 将保险绳 连接在安 全扣并确 认锁紧。 吊臂 Arm 保险绳 safety cord 吊钩： clamp 警告 warning 为确保安全，请将保险绳连接在安全扣并确认锁 紧 For safety, please run the safety cord through the safety cord hole and ensure it is tightened ●RIGGING 5/16... -
Page 6: Place A Unit On A Flat Surface
Take 1 clamp and 1 safety cord out from the package and tighten the clamp with the arm, and then mount the whole unit on the truss, tighten the clamp’s retainers to keep the unit stable. (See the WARNING on the underside of the base as shown above) To pass the SAFETY CORD through the ARM for safety! Always ensure that the unit is firmly anchored to avoid vibration and slipping whilst functioning. -
Page 7: Dmx Terminator
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol DMX512 (1990). -
Page 8: Dmx Start Address
enter the menus. To set or browse through the projector’s functions, press key UP or DOWN. Press the key ENTER to enter the submenus and the current parameters will be displayed while flashing. Press key UP or DOWN to change values(plus or minus) Press key ENTER to save your changes and enter into the upper level menu while flashings stop;... -
Page 9: Dmx Protocol
Address 001 - 512 DMX Address Config Setup Slave MasterSlave Default Slave Master Language Setup English Default：English Chinese Backlight will be off Lcd Light Setup 3minutes after none button is pushed Display Invert Factory Setting PRM Transmit clean Progra Color -128-127 Moto offset Focus... -
Page 10: Technical Data
Dimmer 000-255 000-255 Dimmer in 16 bit Dimmer Fine 000-007 Strobe 008-255 Strobe speed from slow to fast 000-009 White 010-019 White - Magenta 020-029 Magenta Magenta – Orange 030-039 040-049 Orange 050-059 Orange - Yellow 060-069 Yellow 070-079 Yellow- Blue Color wheel 080-089 Blue... - Page 11 ELECTRIC SPECIFICATIONS ，50/60Hz Input voltage: 100V~240V AC 100W @ 230V Input power: Maximum current: AC 0.55A Power factor： PF>90% LIGHT SOURCE SPECIFICATIONS Power Consumption 90W LED White Manufacturers Rated Lamp Life 50000hours Color temperature: 7500K COLORS 1pc color wheel(5colors+Open), continual rotation, magnet sensor positioning Function 1 customized gobo DIMMER...
-
Page 12: Circuit Diagram And Pcb Connections
OPERATION TEMPERATURE: 45 ℃ Maximum ambient temperature SIZES: LIGHT OUTPUT: 投射距离 Distance 光斑直径 Diameter 光照度：Luminuous flux 4791 1198 DISTANCE (m) 12.5 DIAMETER (m) 1.35 2.71 6.76 4.06 5.41 9. CIRCUIT DIAGRAM AND PCB CONNECTIONS ● CIRCUIT DIAGRAM 12/16... -
Page 13: Pcb Connections
●PCB CONNECTIONS Name 13/16... -
Page 14: Component Order Codes
Thermal Sensor Master Board Reserved PWM signal interface Reserved Power Reserved 485 signal interface DMX signal interface 10 Reserved Diver board Name Power LED Driver 10. COMPONENT ORDER CODES 14/16... - Page 15 Name Code No. Remarks K18S-UP200S24 24V/8.3A 6190000004 POWER SWITCH 200W,Kaihui brand 6150000005 TX-3636W90FC120-NUVENG- LED 100 W WHITE LIGHT SOURCE A01 ,Tianxin 6030040000 24BYJ48-51 STEPPING MOTOR 030040235A 25PM30005-04N 42× 37× 73 STEPPING MOTOR 4coils, length 500mm ,Ruibao LED CONSTANT CURRENT 6230000010 SUPPLY OF PR-6820 15/16...
- Page 16 1582 Xingye Avenue, Nancun Panyu Guangzhou, 511442 China TEL: +86-20-3995 2888 PR lighting will try its best to offer accurate and overall information about a product’s technical data. Any changes won’t be notified if necessary. Patented Products. Counterfeiting Will be Prosecuted! P/N:...
Need help?
Do you have a question about the LS 90 Logo and is the answer not in the manual?
Questions and answers