Siruba 700L-BKF1 Instruction Book page 4

在不同階段的注意事項
1. 運輸
(1) 當搬運或移動機器時，請考量機器重量，選擇安全合適的
方式。請參考機器規格。
(2) 採取足夠的安全防護，以避免機台在搬運或移動中掉落。
(3) 為避免意外，運送時不要重覆使用包裝材料。
2. 拆箱
(1) 在拆箱前，檢查機器是否平穩放置，並採用適當的工具維
持拆箱過程的穩定。
(2) 進行拆箱時，遵循外箱上的指示，小心外箱上的釘子或碎
片。
3. 安裝 :
3A. 桌板與腳架
(1) 採用原廠的桌板以確保機器得到足夠的保護與支撐。如果
在安裝或維修時，需要暫時將機器置放於物件上，請確定
該物件有足夠的支撐力。
(2) 如果桌板有裝置滾輪，滾輪需要有煞車鎖定機構，而且在
操作與維修時，煞車機構必需鎖定。
3B. 電線與管路
(1) 電線與管路的材質必需符合規範與需求。.
(2) 電線與管路不能夠有折彎或壓迫。移動的零配件上，電線
與管路需有至少 30mm 以上的預留量 .
(3) 接線時不能有跳火。
(4) 所有接頭都必需要確實固定。當拆除時，務必要抓住接頭
本體。
3C. 接地
(1) 接地是必需的。且需由合格的技師來施工。
(2) 在操作前需確認接地有確實。
3D. 馬達
(1) 馬達的選用，必需符合規範與需求。
(2) 如果馬達為皮帶傳動，務必要安裝保護措施以避免捲入危
險。
4. 在開始操作前
(1) 在開啟電源前，確認所有接頭，電線，管路都完好無損，
確實連結。
(2) 檢查皮帶輪的轉向與標示為同一方向。
(3) 確認腳架滾輪都已鎖定。
(4) 保持作業範圍淨空。
5. 在操作中
IV
PRECAUTIONS TO BE TAKEN IN
VARIOUS OPERATION STAGES
1. Transportation
(1) When lift or move the machine, please take the machine
weight into consideration and apply a safe manner.
Refer to the specification for the information you need for
transportation.
(2) Apply sufficient safety measures when lifting or moving the
machine to avoid falling or dropping.
(3) To avoid unexpected accident, do not reuse the packing
material for transportation.
2. Unpacking
(1) Before proceeding to unpacking, check the balance of
the machine and apply necessary tools to hold the proper
position.
(2) When unpacking, follow the instruction printed on the
cartoon. Be careful of the nails and chips when unpacking
from a wooden rack.
3. Installation:
3A. Table and Stand
(1) Only adopt a qualified genuine table and stand to assure
the holding support. In case you need to leave the machine
on a surface temporarily for service, make sure the surface
is strong enough to hold the weight.
(2) If casters are applied to the table stand, adopt casters with
a locking mechanism only and lock them well to secure the
machine during the operation and service.
3B. Cable and Wire
(1) The cables and wires must comply with the specification
and requirement.
(2) The cables and wires shall be free from bending or extra
force. Reserve a free space of at least 30mm between
cables/wires and the moving parts.
(3) Do not apply starburst connection when wiring.
(4) All connectors must be fixed securely. And always hold the
connector body when removing it.
3C. Grounding
(1) Grounding is necessary and must be done by a certified
technician. (2) Check and ensure the grounding is secured
before operation.
3D. Motor
(1) The motor must comply with the specification and
requirement.
(2) If there is a belt in the motor transmission, adopt or apply a
proper protector to avoid entangling.
4. Before Operation
(1) Before turning on the power, make sure all the connectors,
cables, and wires are free from damage, dropout, or
looseness.
(2) Check and make sure the pulley rotation follows the same
direction as labels.
(3) Make sure all the stand casters are locked or fixed in
position.
(4) Keep the working area clean from obstacles.
5. During Operation
(1) Always keep your fingers, hair, or clothing away from the
moving components and moving area. Do not place your
personal belongings on the machine.