EMS AIRFLOW ONE Instructions For Use Manual page 12

Powder sprays out of chamber at depressurization
1° Powder chamber is filled beyond the maximum level marked
2° Remove the powder exceeding the MAX sign on the bottle
Powder leaks under the AIRFLOW
The AIRFLOW pinching element might be worn out or the air interface is dirty and is leaking powder
®
1° Disconnect the cord, clean the air jack and connect again. If problem persists, go to Step 2
2° Replace your AIRFLOW
3° If still not solved, contact the EMS service center in Dallas
Powder chamber is leaking
1° Clean the chamber with a wet cloth, in particular the cap and the bottom o-rings. Also clean the connecting
elements on the device
2° If still not solved, replace the powder chamber with a new one
4.8- To contact EMS service center
Electro Medical Systems Dallas Corporation
11886 Greenville Avenue, #120
US-Dallas, TX 75243
Phone: +1 972 690 83 82
Fax: +1 972 690 89 81
Email: info@ems-na.com
SUSTAINABILITY
I- DISPOSAL OF WASTE
The device must not be discarded in domestic household waste. Should you wish to definitively
dispose of the device, please comply with the regulations that apply in your country.
Other parts of this device, including tips/inserts, and chemicals must be disposed of according to
your country's regulations.
Keep the original packaging until the device is to be disposed of permanently. It can be used for
shipping or storing.
II- SUSTAINABLE DESIGN
The device, on a voluntary basis, respects the latest Eco design low energy standby and off mode
consumption regulation
Printed instructions are aligned with a sustainable development policy and are certified « Myclimate
neutral imprimerie » and « FSC ».
WARRANTY
Scan
for
support
Certify your practice and receive a second year of warranty. This warranty is only valid if you have completed your first yearly
maintenance within 12 months following purchase.
For more details, scan the QR code.
Warranty is void if the device has been used with non-original EMS powder and handpieces. Warranty is void if the device has
been opened.
EMS and the distributor of this device accept no liability for direct or consequential injury or damage resulting from improper
use, arising in particular through non-observance of the instructions for use, or improper preparation and maintenance.
EMS declines the responsibility for the safety of the device and declares the warranty null and void if service or repair is carried
out by an unauthorized third party or if non-genuine spare parts are used.
19 European Commission Regulation N°1275/2008 of 17 December 2008 regarding the Eco design requirements for standby and off mode electric power
consumption of electronic household and office equipment.
22
Handpiece cord system
®
Handpiece cord with a new one
®
. Packaging cardboards are recycled and recyclable.
19
TECHNICAL DATA COLLECTION AND PRIVACY POLICY
During maintenance and/or repair of the device, EMS or any authorized EMS repair center will have access to certain technical
information such as usage statistics (hereinafter "Technical Data"), collected during the device service.
Such technical data shall be analyzed and used by EMS in its legitimate interest, e.g. to carry out statistical analysis and to
improve its customer service and/or its Research and Development processes.
EMS may also use such technical data along with your personal details in order to be able to understand your personal usage
of the device and offer you a better customer experience and tailored service. However, you can unsubscribe from this process
at any time, by simply sending us an email at privacy@ems-ch.com.
Rest assured that these activities will be carried out in compliance with applicable data protection laws. For any questions
regarding your personal data, please consult our privacy policy at www.ems-company.com or send an email to privacy@ems-
ch.com.
TECHNICAL DESCRIPTION
Manufacturer EMS ELECTRO MEDICAL SYSTEMS SA, CH-1260 Nyon, Switzerland
Model AIRFLOW ONE, product code FT-230
Classification IEC 60601-1 Electrical Insulation Class-I
Applied part Type B
IP20 Control unit
IP21 Foot pedal
Operating mode Continuous operation
Power supply 100-240Vac, 50-60Hz, 4A max.
Power consumption OFF-mode / Stand-by: 0.5W max.
Max: 700VA
Fuse 5A, T (slow), 250Vac, H type (=T5H250V)
Wireless communication Max 8 dBm EIRP, 2.4GHz band, Bluetooth
module
Weight Control Unit 5kg max. (full operating condition)
Foot pedal: 0.35kg max. (wireless pedal)
Dimensions Control Unit: Height: 245 mm, Width: 205 mm, Length: 290 mm
Wireless pedal: Diameter 135 mm, Height 35 mm
Operating conditions Temperature: 10°C to 35°C
Humidity: 30% to 75%
Altitude: Max 2000m
Storage conditions Device:
Temperature: -10°C to 30°C, no water inside
Humidity: 10% to 95% not condensed
Pressure: 500hPa to 1060hPa
Application box:
Temperature: up to 40°C
Transport conditions
Temperature: -29°C to 38°C, no water inside
Humidity: 10% to 95% not condensed
Pressure: 500hPa to 1060hPa
Input fluids Water: pressure 2-5bar, temperature 10-30°C, salinity 0.2% max., hardness from 8 to 12°dH, minimum
flow-rate 100ml/min, RECTUS 20KA connector type. EN-1717 compliant water network/inlet is required.
Note: The pH and particle size information are not relevant.
Air: pressure 4.5-7bar, dry-only (humidity 1.032g/m3 max.), oil filtered 0.1mg/m3 max., minimum flow-
rate 20 Nl/min at 4.5bar, RECTUS 21KA connector type
Output fluids Water: min. 40ml/min. for AIRFLOW
Air: max pressure 5bar for AIRFLOW
A few drops may escape when the water setting is at "0"
Shelf life WATER and CLEANER bottles: 5 years
®
Validated lifetime Handpieces (main bodies): 1000 sterilization cycles
Expected service life Device: 7 years, having regular yearly preventive maintenance
radio module
®
®
®
23