Page 1
SOLO 25-35 EV MANUALE PER L’USO, L’INSTALLAZIONE E LA MANUTENZIONE USER, INSTALLATION AND SERVICING INSTRUCTIONS Per la consultazione della documentazione visita il nostro sito www.sime.it To consult the documentation, visit our website www.sime.it Fonderie SIME S.p.A. 6333574 - 07/2023 - R0...
Page 3
- chiudere i rubinetti del combustibile e dell’acqua dell’impianto idrico. – si riserva di va- Fonderie SIME S.p.A. riare in qualunque momento e senza – Allo scopo di assicurare un'efficienza preavviso i propri prodotti nell’intento ottimale dell'apparecchio...
Page 4
DIVIETI È VIETATO È VIETATO – L’uso dell’apparecchio ai bambini di – Modificare i dispositivi di sicurezza o di età inferiore a 8 anni. L’apparecchio regolazione senza l’autorizzazione e le può essere utilizzato da bambini di età indicazioni del costruttore dell'appa- non inferiore a 8 anni e da persone con recchio.
Page 5
Gentile Cliente, STRUTTURA DEL MANUALE La ringraziamo per aver acquistato il Gruppo Termico Sime SOLO Questo manuale è organizzato nel modo sotto evidenziato. , un apparecchio con caratteristiche tecniche e prestazionali in grado di soddisfare le Sue esigenze di riscaldamento nella massima sicurezza con costi di esercizio contenuti.
OPERARE CON IL GRUPPO TERMICO SOLO 25-35 EV – richiudere il rubinetto di carico (B). Quadro comandi Il Quadro Comandi permette a tutti gli operatori di effettuare le regolazioni necessarie alla gestione dei Gruppi Termici Sime e degli impianti collegati. SOLO EV Fig. 3 Fig.
Il bruciatore eseguirà il preriscaldamento del combustibile, se- 1.5.2 Blocco bruciatore guito dalla preventilazione, dopodiché accenderà la fiamma e Nel caso si verificassero anomalie di accensione o di funziona- funzionerà alla sua potenza regolata fino a quando sarà rag- mento, il Gruppo Termico effettuerà un arresto di blocco e la giunta la temperatura impostata sul termostato ambiente.
SPEGNIMENTO 1.5.4 Pompa in avaria : Il LED segnala lo stato della pompa in base alla colora- LED (D) zione che assume illuminandosi, come riportato sotto. Spegnimento temporaneo – Verde acceso : funzionamento regolare – Spento : richiedere l’intervento di Personale Professionalmen- Nel caso di assenze temporanee, fine settimana, brevi viaggi, te Qualificato ecc.
MANUTENZIONE SMALTIMENTO Regolamentazioni Smaltimento dell’apparecchio (Direttiva Europea 2012/19/UE) Per un funzionamento efficiente e regolare dell'apparecchio è consigliabile che l'Utente incarichi un Tecnico Professional- L'apparecchio ed i dispositivi elettrici ed elet- mente Qualificato affinché provveda, con periodicità ANNUALE , tronici, provenienti da nuclei domestici o clas- alla sua manutenzione.
Page 13
DESCRIZIONE DELL'APPARECCHIO INDICE 5.12 Regolazione pompa di circolazione ....20 DESCRIZIONE DELL'APPARECCHIO 5.12.1 Selezione del modo operativo e della curva Caratteristiche ....... . . 14 caratteristica .
DESCRIZIONE DELL'APPARECCHIO Caratteristiche I Gruppi Termici, in ghisa, Sime SOLO EV sono sistemi integrati con bruciatore di gasolio, ad aria soffiata. Sono destinati a chi tiene in opportuna considerazione le prestazioni, la silenziosità del funzionamento e la riduzione degli spazi.
La sostituzione dei dispositivi di sicurezza deve essere effettuata esclusivamente da personale professional- mente qualificato utilizzando solamente componenti originali Sime . Identificazione Le caldaie SOLO EV sono identificabili attraverso: è posizionata all’esterno della confezione e riporta il codice, il numero di matricola della caldaia e il codice a Etichetta imballo: barre.
14 15 18 17 Apparecchiatura elettrica di co- Vite regolazione aria Presa 7 poli mando e controllo Corpo alloggiamento girante Piede d’appoggio a terra LED richiesta calore (verde) Sensore rivelatore fiamma Motore elettrico per pompa e Connessione tra apparecchiatura Tasto di sblocco e spia luminosa ventilatore e trasformatore d’accensione di blocco (rossa)
- CO - CO (ppm) - NOx (ppm) - indice di Bacharach - temperatura fumi di scarico. ATTENZIONE Tutte le operazioni devono essere eseguite esclusivamente dal Servizio Tecnico Sime o da Personale Professionalmente Qualificato, seguendo le istruzioni presenti in questo manuale.
5.11 Pompa impianto alta efficienza 5.12 Regolazione pompa di circolazione La pompa ad alta efficienza è corredata dai LED di segnalazione 5.12.1 Selezione del modo operativo e della curva ca- (1), (2), (3) e dal tasto di comando (4). ratteristica La selezione del modo di regolazione e delle curve caratteristi- che corrispondenti si ottiene nel seguente modo: –...
Pressione differenziale variabile Δp-v (I, II, III) 5.13.3 Bloccare/sbloccare il tasto Consigliata in caso di sistemi di riscal- Il blocco tastiera viene attivato premendo a lungo (8 secondi) damento a doppia mandata con radiato- il tasto di comando (4) e blocca le impostazioni della pompa. Il ri, per la riduzione dei rumori di flusso blocco tastiera protegge da modifiche involontarie o non auto- sulle valvole termostatiche.
5.14.2 Bruciatore Sensore fiamma Motore ventilatore Trasformatore Riscaldatore del combustibile Elettrovalvola gasolio presa 7 poli per connessione al quadro comandi del Gruppo Termico Fig. 27...
Page 25
ISTRUZIONI PER L'INSTALLAZIONE E LA MANUTENZIONE INDICE INSTALLAZIONE MANUTENZIONE Ricevimento del prodotto ......26 Regolamentazioni ......36 Pulizia interna .
Sime adeguate protezioni antin- con l'OBBLIGO di indossare fortunistiche. Ricevimento del prodotto Gli apparecchi Sime SOLO EV vengono forniti in collo unico, pro- tetti da un sacco di nylon, e posti su pallet in legno. Fig. 29 SOLO EV Descrizione...
ATTENZIONE Nuova installazione o installazione in sosti- Utilizzare attrezzature e protezioni antinfortunistiche tuzione di altro apparecchio adeguate sia per togliere l'imballo, sia per la movi- Quando i gruppi termici SOLO EV vengono installati su impianti mentazione dell'apparecchio. Rispettare il peso mas- vecchi o da rimodernare, è...
È utile annotare le quantità di acqua di riempimento, di rabbocco e i valori della qualità dell’acqua utilizzata. Collegamenti idraulici H = x-y Le dimensioni degli attacchi idraulici dei Gruppi Termici Sime Fig. 33 SOLO EV sono riportate di seguito.
Lunghezza tubo (m) H (m) Ø6 mm Ø8 mm Ø10 mm ATTENZIONE – L'impianto di alimentazione del combustibile deve essere adeguato alla portata del bruciatore e deve essere dotato di tutti i dispositivi di sicurezza e di controllo prescritti dalle Norme vigenti nel paese di utilizzo dell'apparecchio.
In fat ti, se non è ese gui ta con gli I Gruppi Termici Sime SOLO EV sono classificati di "Tipo B" op por tu ni cri te ri, si pos so no ave re di sfun zio ni nel bru cia to re, (B23P) e di "TIPO C"...
Page 31
Ø80 mm, non dovrà es- sere superiore a 7,0 metri + n°2 curve a 90°. AVVERTENZA Utilizzare esclusivamente accessori originali Sime e assicurarsi che il collegamento sia realizzato in ma- niera corretta, così come indicato nelle istruzioni for-...
6.12 Riempimento e svuotamento I Gruppi Termici Sime SOLO EV sono dotati del dispositivo di ri- empimento impianto. 6.12.1 Operazioni di RIEMPIMENTO IMPIANTO Prima di effettuare le operazioni di riempimento: –...
MESSA IN SERVIZIO AVVERTENZA – regolare il termostato riscaldamento (1) a circa 3/4 del campo di regolazione (circa 75°C) Le operazioni di messa in servizio e prima accensione – posizionare l’interruttore principale (2) dell’apparecchio su devono essere effettuate SOLO da Personale Profes- "1"...
7.3.3 Controllo depressione pompa Regolazione bruciatore Il vacuometro per il controllo della depressione della pompa 7.3.1 Posizione della serranda dell’aria deve essere collegato al punto (5). La depressione massima consentita è di 0,4 bar. La serranda dell'aria si regola ruotando la vite (1) con la chiave Con depressione più...
7.3.5 Regolazione della combustione I bruciatori lasciano la fabbrica tarati in accordo al paragrafo “Regolazioni del bruciatore a varie altitudini di installazione”. In caso di condizioni di temperatura esterna tali che possano influenzare la combustione, si consiglia di regolare la CO secondo lo schema seguente.
MANUTENZIONE Regolamentazioni Per un funzionamento efficiente e regolare dell'apparecchio è consigliabile che l'Utente incarichi un Tecnico Professional- mente Qualificato affinché provveda, con periodicità ANNUALE , alla sua manutenzione. AVVERTENZA – Le operazioni di seguito descritte devono essere effettuate SOLO da personale professionalmente qualificato con l'OBBLIGO di indossare adeguate pro- tezioni antinfortunistiche.
Se si dovesse rimuovere il diffusore (21) dal suo allog- giamento, esso deve poi essere riposizionato, assicu- – estrarre i turbolatori (13) (n°5 per modello SOLO 25 EV ; n°2 per randosi che la spina (23) sia inserita nel foro (22).
8.2.5 Verifica posizione gruppo elica di turbolenza 8.2.6 Verifica posizione del boccaglio Per verificare la posizione del gruppo elica di turbolenza: Verificare che la distanza (A), tra il boccaglio (26) e l'ugello (20), – smontare il boccaglio, come descritto nel paragrafo "Pulizia e sia quella prevista dalla dima (25), come illustrato in figura.
8.2.8 Sostituzione della bobina 8.2.10 Pulizia della girante Per sostituire la bobina: Per pulire la girante del ventilatore: – togliere il connettore (1); – svitare le viti (1) e rimuovere il condotto di aspirazione aria (2) – rimuovere il dado (2) con la chiave fornita a corredo; –...
Nella tabella di seguito sono riportati i componenti soggetti a usura e il loro ciclo di vita, al termine del quale è opportuno che vengano sostituiti esclusivamente dal Servizio Tecnico Sime o da Personale Professionalmente Qualificato Ciclo di vita...
Eventuali anomalie e rimedi 8.3.1 Bruciatore Richiesta di Consenso Motore calore Sì riscaldatore Sì Sì si avvia (entro 400s) Verifica che Motore Pompa Sostituire Sì il LED verde bloccato bloccata condensatore sia acceso motore Verifica che Riscaldatore Sì Sì il LED verde Sì...
Page 42
Richiesta di calore Sì Blocco C’è un falso Rimuovi la Avviamento Fase di Sì durante la Sì segnale di Sì causa del Sì Motore riscaldamento fase di pre- fiamma falso segnale ventilazione di fiamma Verifica la funzionalità del sensore fiamma Sostituisci Il sensore Sì...
8.3.2 Pompa Colore LED Stato della pompa Eventuale anomalia Possibile rimedio Il sistema idraulico della pompa Funzionamento turbina viene alimentato, ma la pompa non - Verificare la tensione di rete ha tensione di rete Rosso-Verde Funzionamento a secco Aria nella pompa - Verificare l’assenza di perdite nell’impianto lampeggiante - Verificare la tensione di rete...
8.3.3 Impianto Tipo di anomalia o guasto Causa Rimedio - Verificare pulizia corpo bruciatore Odore di prodotti incombusti Dispersione fumi in ambiente - Verificare pulizia ed ermeticità scarico fumi e generatore - Controllare qualità combustione Bruciatore mal regolato - Controllare regolazione del bruciatore (analisi fumi) Il generatore si sporca in breve tempo Canna fumaria intasata - Pulire condotto fumi...
Page 47
Sime – reserves the right Fonderie SIME S.p.A. maintenance and checks are carried to make improvements to its prod- ONCE A YEAR ucts at any time without prior notice, without compromising their essential characteristics.
Page 48
RESTRICTIONS IT IS FORBIDDEN IT IS FORBIDDEN – To allow children under the age of 8 to – To modify the safety or adjustment use the appliance. The appliance can devices without authorization and in- be used by children no younger than structions from the manufacturer.
Page 49
Dear Customer, MANUAL STRUCTURE Thank you for purchasing the Sime SOLO EV thermal unit, a de- This manual is organized as follows. vice possessing technical and performance characteristics ca- pable of satisfying your space heating requirements with the utmost safety and limited running costs.
Page 51
USER INSTRUCTIONS TABLE OF CONTENTS OPERATING WITH THE SOLO 25-35 EV THERMAL UNIT SHUTDOWN Temporary shutdown......54 Shutting down for long periods .
OPERATING WITH THE SOLO 25-35 EV THERMAL UNIT – close the filling valve (B). Control panel The control panel enables all operators to make the necessary adjustments for managing Sime SOLO EV thermal units and the systems connected to them. Fig. 3 Fig. 1 Ignition ;...
The burner will pre-heat the fuel and perform the pre-ventila- 1.5.2 Burner lock-out tion cycle; it will then ignite the flame and operate at its adjust- Should any faults occur during its ignition or operation, the ed power until the temperature set on the room thermostat is thermal unit will perform a lock-out and the red signalling in- reached.
SHUTDOWN 1.5.4 Faulty pump : The LED will signal the pump status on the basis of its LED (D) colour when lit, as shown below. Temporary shutdown – Lit green : normal operation – Off : request professionally qualified personnel to intervene If the user is away temporarily, for a weekend, short trip etc and –...
MAINTENANCE DISPOSAL Adjustments Disposal of the equipment (European Di- rective 2012/19/EU) For the appliance to operate correctly and efficiently it is recom- mended that the User calls upon the services of a Professionally At the end of their life span, the appliance Qualified Technician to carry out ANNUAL maintenance.
Page 57
DESCRIPTION OF THE APPLIANCE TABLE OF CONTENTS 5.12 Setting the circulation pump ..... 64 DESCRIPTION OF THE APPLIANCE 5.12.1 Selecting the operating mode and the Characteristics .
DESCRIPTION OF THE APPLIANCE Characteristics The Sime SOLO EV cast iron thermal units are integrated systems with diesel blown-air burner. They are specially designed for users who privilege high performances, silent operation and compact dimensions. – The SOLO EV thermal unit is the version for space heating only. It can be a TYPE B23P (open), if it draws combustion air from the environment in which it is installed, or TYPE C23P (sealed), if it draws combustion air from the outside.
WARNING – water pressure switch. Safety device may only be replaced by professional qualified personnel using Sime original spare parts. Identification The SOLO EV boilers can be identified by means of: located on the outside of the packaging, it includes the code and serial number of the boiler in addition to the Packaging label: barcode.
Structure Thermowell Smoke outlet fitting Pressure gauge System filling valve System return (R) System pump (PI) Automatic bleed valve System discharge valve Side panels Minimum-pressure water pres- Appliance support frame Burner (BR) sure switch Front panel Flame viewing window Expansion vessel (VE) Control panel Cast iron body Fitting for filling...
14 15 18 17 Electrical control and command Air regulation valve 7-pin socket equipment Impeller housing body Foot Heat request LED (green) Flame detector sensor Electric motor for pump and fan Connection between the equip- Unlock button and lock-out indi- Capacitor ment and the ignition transformer cator light (red)
- CO (ppm) - NOx (ppm) - Bacharach index - flue gas temperature. WARNING All operations must be carried out exclusively by the Sime Technical Support Service or by professionally qualified personnel, according to the instructions appearing in this manual.
Main water circuit KEY: System delivery System return System filling Thermal unit body System filling valve Safety valve (VS) Automatic bleed valve Expansion vessel (VE) Diesel burner (BR) High-efficiency system pump (PI) Pressure gauge System discharge valve System water pressure switch Fig.
5.12 Setting the circulation pump 5.11 High-efficiency system pump The high-efficiency pump is fitted with signalling LEDs (1), (2), 5.12.1 Selecting the operating mode and the charac- (3) and with the command button (4). teristic curve The adjustment mode and the corresponding characteristic curves are selected in the following way: –...
Variable differential pressure Δp-v (I, II, III) 5.13.3 Locking/unlocking the button Recommended in case of heating sys- The keypad lock is activated by long pressing (8 seconds) the tems with double delivery and radiators, command button (4) and it blocks the pump settings. The key- for the reduction of flow noises on the pad lock protects the pump against involuntary/unauthorised thermostatic valves.
5.14.2 Burner Flame sensor Fan motor Transformer Fuel heater Diesel solenoid valve 7-pole socket for connection to the control panel of the Thermal Group Fig. 27...
Page 69
INSTALLATION AND SERVICING INSTRUCTIONS TABLE OF CONTENTS INSTALLATION MAINTENANCE Receiving the product ......70 Adjustments.
Service or by qualified professionals who MUST suitable protective safety equipment. wear Receiving the product Appliances Sime SOLO EV are supplied in a single package, pro- tected by a nylon cover, placed on wooden pallets. Fig. 29 SOLO EV...
WARNING New installation or installation of a re- Use suitable tools and accident protection when re- placement appliance moving the packaging and when handling the appli- When SOLO EV thermal units are installed on old systems or sys- ance. Observe the maximum weight that can be lifted tems that need to be upgraded, we recommend checking that: per person.
H = x-y Plumbing connections Fig. 33 The size of the hydraulic fittings of Sime SOLO EV thermal units are shown below. Pipe lenght (m) H (m) Ø6 mm Ø8 mm...
Pipe lenght (m) H (m) Ø6 mm Ø8 mm Ø10 mm WARNING – The fuel supply system must be sized in relation to the burner flow rate and must be equipped with all the safety and control devices envisaged in the standards in force in the country where the appli- ance is used.
“Type B” (B23P) Sime SOLO EV malfunctions, noise amplification and the build up of soot, con- and “Type C” (C23P), while the smoke discharge and combus- densate and deposits.
Page 75
The maximum allowed length (L) of the air intake pipe with Ø80 mm diameter must not exceed 7,0 metres + 2 x 90° elbows. CAUTION Only use original Sime accessories and make sure that the connection is made correctly, as explained in the instructions supplied with the accessories.
Electrical connections It is compulsory: thermal units require the connections shown be- Sime SOLO EV – to use an omnipolar cut-off switch, disconnect low, which must be carried out by the installer or by profession- switch, in compliance with EN standards (contact ally qualified personnel.
COMMISSIONING CAUTION – adjust the heating thermostat (1) to roughly 3/4 of the adjust- ment range (circa 75°C) The commissioning and initial start-up operations – shift the appliance’s main switch (2) to "1" (on) and check that must be carried out ONLY by professionally qualified the green signalling LED (3), situated on the control panel, is personnel who must follow the indications provided lit.
7.3.3 Checking the pump’s negative pressure Adjusting the burner The vacuum gauge for checking the pump’s negative pressure 7.3.1 Air shutter position must be connected to point (5). The maximum allowed negative pressure is 0,4 bar. The air shutter can be adjusted by turning the screw (1) with the With a higher negative pressure, diesel turns into gas, causing Allen key (2) provided: cavitation of the pump and damaging it as a result.
7.3.5 Adjusting the combustion The burners leave the factory calibrated on the basis of the indications of the paragraph “Adjusting the burner at various installation altitudes”. If the outdoor temperature is such that it may influence combustion, we recommend adjusting the Co according to the following diagram.
MAINTENANCE Adjustments For the appliance to operate correctly and efficiently it is recom- mended that the User calls upon the services of a Professionally Qualified Technician to carry out ANNUAL maintenance. CAUTION – The maintenance interventions described must ONLY be carried out the professionally qualified personnel who MUST wear suitable protective safety equipment.
– clean all the components properly. Fig. 58 CAUTION – remove the turbulators (13) (5 for model SOLO 25 EV ; 2 for If the diffuser (21) must be removed from its housing, model SOLO 35 EV ) and brush them to remove the soot it must then be put back in place while making sure that the pin (23) is inserted through the hole (22).
8.2.5 Check the position of the turbulence rotor unit 8.2.6 Checking the position of the nose To check the position of the turbulence rotor unit: Check that the distance between the nose (A) (26) and the noz- – dismantle the nose, as described in the paragraph “Cleaning zle (20) matches the one on the template (25), as shown in the and replacing the combustion head”, if it has not been done figure.
8.2.8 Replacing the coil 8.2.10 Cleaning the impeller To replace the coil: To clean the fan impeller: – remove the connector (1); – loosen the screws (1) and remove the air intake duct (2) – remove the nut (2) using the spanner provided; –...
8.2.13 Scheduled replacement of worn components The table below shows the components subject to wear and their life cycle, at the end of which they should be replaced exclusively by the Sime Technical Service or by professionally qualified personnel Life cycle...
Possible faults and solutions 8.3.1 Burner Heater The motor Heat request consent starts (within 400 s) Check that Pump Motor Replace the the green seized seized motor capacitor LED is on Check that Heater the green damaged LED is on Clean the Replace the Check the...
Page 86
Heat request Lock-out There’s a Eliminate the Motor start- Heating phase during false flame cause of the the pre- signal false flame ventilation signal phase Check the flame sensor’s efficiency Replace the Does the flame control and sensor work command correctly? device Replace the...
8.3.2 Pump LED colour Pump status Fault Possible solution The hydraulic system in the pump Turbine operation is powered but the pump is not - Check network voltage receiving any mains voltage Red/Green Dry operation Air in the pump - Check for leaks in the system flashing - Check network voltage The motor has difficulties turning.
8.3.3 System Type of malfunction or fault Cause Solution - Check the cleanliness of the burner body Dispersion of fumes in the - Check the cleanliness and tightness of the smoke outlet and Smell of unburnt products environment generator - Check the combustion quality Burner poorly adjusted - Check the burner adjustment (fume analysis) The generator gets dirty quickly...
Page 90
ALLEGATI - ANNEXES Scheda prodotto caldaia - Boiler product board SOLO EV Classe efficienza energetica stagionale riscaldamento C.H. energy efficiency class Potenza termica (kW) Heat output (kW) Consumo annuo di energia riscaldamento (GJ) C.H. annual energy consumption (GJ) Efficienza energetica stagionale riscaldamento (%) C.H.
Page 91
Daily electricity consumption Daily fuel consumption Recapiti Fonderie Sime S.p.A. Via Garbo 27, 37045 Legnago (VR) ITALIA Contact details a. Regime ad alta temperatura: temperatura di ritorno di 60°C all’entrata e 80°C di temperatura di fruizione all’uscita dell’apparecchio. b. Bassa temperatura: temperatura di ritorno (all’entrata della caldaia) per le caldaie a condensazione 30°C, per le caldaie a bassa temperatura 37°C e per le altre caldaie 50°C.
Page 92
Daily electricity consumption Daily fuel consumption Recapiti Fonderie Sime S.p.A. Via Garbo 27, 37045 Legnago (VR) ITALIA Contact details a. Regime ad alta temperatura: temperatura di ritorno di 60°C all’entrata e 80°C di temperatura di fruizione all’uscita dell’apparecchio. b. Bassa temperatura: temperatura di ritorno (all’entrata della caldaia) per le caldaie a condensazione 30°C, per le caldaie a bassa temperatura 37°C e per le altre caldaie 50°C.
Need help?
Do you have a question about the SOLO 25 EV and is the answer not in the manual?
Questions and answers