Gree Dettson LOMO 19 Installation Manual page 38

Service Manual
(3) At this time, 1hour will be automatically increased at the timer
position on the remote control, (that are "2hours" or "3hours" or
"8hours"), the place of setting temperature "88" will display the
corresponding temperature of last setting sleep
curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours
temperature setting finished, sleep,curve setting finished, at this
time, the remote controller will resume the original timer display;
temperature display will resume to original setting temperature.
● Sleep3- the sleep curve setting under Sleep mode by DIY could
be inquired:
The user could accord to sleep curve setting method to inquire
the presetting sleep curve, enter into user individuation sleep
setting status, but do not change the temperature, press "Turbo"
button directly for confirmation. Note: In the above presetting or
enquiry procedure, if continuously within 10s, there is no button
pressed, the sleep curve setting within 10s, there is no button
pressed, the sleep curve setting status will be automatically quit
and resume to display the original displaying. In the presetting
or enquiry procedure, press "ON/OFF" button, "Mode" button,
"Sleep" button, the sleep curve setting or enquiry status will quit
similarly.
12. WiFi button
Press " WiFi " button to turn on WiFi function, "WiFi " icon will
be displayed on the remote controller; Hold " WiFi " button for 5s
to turn off WiFi function and " WiFi " icon will disappear.
U n d e r o f f s t a t u s , p r e s s " M O D E " a n d " W i F i " b u t t o n s
simultaneously for 1s, WiFi module will restore factory settings.
NOTE:
● This function is only available for some models.
13. button
Press this button to achieve the on and off of health and
scavenging functions in operation station. Press this button
for the first time to start scavenging function; LCD displays
" ". Press the button for the second time to start health and
scavenging functions simultaneously; LCD displays "
Press this button for the third time to quit health and scavenging
functions simultaneously. Press the button for the fourth time to
start health function; LCD display "
repeat the operation above.
NOTE:
● This function is applicable to partial of models.
14. LIGHT button
Press this button to turn on or turn off the display light on the
indoor unit.
The display light is defaulted on after energization.
15. TEMP button
Press this button, you can see indoor set temperature, indoor
Technical Information
" and " ".
". Press this button again to
ambient temperature on indoor unit's display. The setting on
remote controller is selected circularly as below:
no display
Function introduction for combination buttons
1. Energy-saving function
Under cooling mode, press "TEMP" and "CLOCK" buttons
simultaneously to start up or turn off energysaving function.
When energy-saving function is started up, "SE" will be shown
on remote controller, and air conditioner will adjust the set
temperature automatically according to ex-factorysetting to reach
to the best energy-saving effect. Press "TEMP" and "CLOCK"
buttons simultaneously again to exit energy-saving function.
NOTE:
● Under energy-saving function, fan speed is defaulted at auto
speed and it can't be adjusted.
● Under energy-saving function, set temperature can't be
adjusted. Press "TURBO" button and the remote controller won't
send signal.
● Sleep function and energy-saving function can't operate at the
same time. If energy-saving function has been set under cool
mode, press sleep button will cancel energy-saving function. If
sleep function has been set under cool mode, start up the energy-
saving function will cancel sleep function.
2. 8°C heating function
Under heat mode, press "TEMP" and "CLOCK" buttons
simultaneously to start up or turn off 8°C heating function. When
this function is started up, "
remote controller, and the air conditioner keep the heating status
at 8°C.
Press "TEMP" and "CLOCK" buttons simultaneously again to exit
8°C heating function.
NOTE:
● Under 8°C heating function, fan speed is defaulted at auto
speed and it can't be adjusted.
● Under 8°C heating function, set temperature can't be adjusted.
Press "TURBO" button and the remote controller won't send
signal.
● Sleep function and 8°C heating function can't operate at the
same time. If 8°C heating function has been set under heat
mode, press sleep button will cancel 8°C heating function. If
sleep function has been set under heat mode, start up the 8°C
heating function will cancel sleep function.
● Under °F temperature display, the remote controller will display
46°F heating.
3. Child lock function
Press "▲" and "▼" simultaneously to turn on or turn off child lock
" and "8°C" will be shown on
35