Advertisement
Quick Links
Advertisement
Related Manuals for fantastic furniture COMO
Summary of Contents for fantastic furniture COMO
- Page 1 Assembly Instructions COMO DRESSER 6 DRW VER 1.1...
- Page 2 WARNING WARN NG FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE THAT IS NOT COVERED BY YOUR WARRANTY Lay out all of the components on a soft surface Read Instructions carefully. as if you were preparing to do a jigsaw puzzle. Check no parts are missing.
-
Page 3: What You Need
What You Need To Assemble The Body Top Panel Rail (P1) (Tools not provided) (P5) Flat Blade Screwdriver Phillips Head Screwdriver Rail Right Side Mallet (P5) Panel (P3) 2 x Back Panel Rail (P9) (P5) Divider (P4) Rail (P7) Rail (P6) Drawer Back Right Drawer... - Page 4 Step 1 You will need: 3 x CL Runner Tracks (H6) 9 x Small Screws (H5) (P2) Attach 3 x CL Runner Tracks (H6) to Left Side Panel (P2) with 9 x Small Screws (H5). Step 2 You will need: 3 x CR Runner Tracks (H7)
- Page 5 Step 4 You will need: 3 x CL Runner Tracks (H6) 9 x Small Screws (P4) (H5) Attach 3 x CL Runner Tracks (H6) to Divider (P4) with 9 x Small Screws (H5). Step 5 You will need: 3 x CR Runner Tracks (H7) 9 x Small...
- Page 6 Step 7 (P4) You will need: 1 x Cam Nut (H4) (P6) (P3) Insert 1 x Cam Nut (H4) into the hole of Divider (P4). Rotate the cam nut so the arrows point towards the incoming cam bolt. Push Divider (P4) into place and tighten the cam nut. Step 8 (P5) (P5)
- Page 7 Step 10 You will need: 3 x Cam Nuts (P2) (H4) 4 x Long Screws (H15) 6 x Plastic Glides (H17) (P6) (P3) 20mm Insert 3 x Cam Nuts (H4) into the holes of Rails (P6,P7) and (P8). Rotate the cam nuts so the arrows point towards the incoming cam bolts. Push Left Side Panel (P2) into place and tighten the cam nut.
- Page 8 Step 12 You will need: Dowels (H1) (P1) 6 x Cam Nuts (H4) (P3) CAREFULLY TURN (P2) UNIT OVER Insert 6 x Dowels (H1) into Side Panels (P2,P3) and Divider (P4). Insert 6 x Cam Nuts (H4) into the holes of Side Panels (P2,P3) and Divider (P4). Rotate the cam nuts so the arrows point towards the incoming cam bolts.
- Page 9 Step 14 You will need: Dowel (H1) 5 x Small Cam Bolts (P10) (H10) Insert 1 x Dowel (H1) into Drawer Front (P10). Attach 5 x Small Cam Bolts (H10) as shown. Step 15 This is how a cam nut works ..The head of the cam bolt goes into the open You will need:...
- Page 10 Step 17 You will need: 6 x Long Screws (H2) (P15) (P12) (P14) (P13) (P10) Attach Drawer Back (P15) to Drawer Sides (P12,P13) with 4 x Long Screws (H2), then attach Drawer Back (P15) to Support Rail (P16) with 2 x Long Screws (H2). Make sure that the groove lines up the whole way around the drawer.
- Page 11 Step 20 Top View Left (P10) Right (P11) There are specific Left (P10) and Right (P11) Drawers. Put the drawers into the chest. So the drawer fronts align with the outside of the side panels. Please make sure your chest is sitting squarely on the floor, then tighten all the screws and bolts –...
- Page 12 Step 21 We strongly advise that you use the wall safety strap provided to You will need: prevent the unit toppling 1 x Safety Strap (H12) 1 x Screw (H13) 1 x Washer (H14) Attach Safety Strap (H12) to the Top Panel (P1) using 1 x Screw (H13) and 1 x Washer (H14). Step 22 Seek advice from a qualified trades person on how to...