Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-K3BC411X Series
Summary of Contents for HIKVISION DS-K3BC411X Series
- Page 1 Swing Barrier Quick Start Guide...
- Page 2 BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;...
- Page 3 During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
- Page 4 Swing Barrier • User Manual FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 5 Swing Barrier • User Manual Applicable Models This manual is applicable to the models listed in the following table. Series Model DS-K3BC411X-L DS-K3BC411X DS-K3BC411X-R Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text.
-
Page 6: Table Of Contents
Swing Barrier • User Manual CONTENTS 1 Product introduction ................ 6 1.1 Brief introduction ................6 1.2 Product structure and principle ............6 1.3 Function Features ................9 1.4 Technical parameters ..............9 2 Equipment Installation..............9 2.1 Installation notes ................9 2.2 Equipment Installation.............. -
Page 7: Product Introduction
Swing Barrier • User Manual 1 Product introduction 1.1 Brief introduction The flap /slide barrier and swing gate is a kind of 2-way speed access control equipment designed for places with high class security requirements. It is easy to combine IC access control, ID access control, code reader, fingerprint, face recognition and other identification devices，It realizes the intelligent and efficient management of passage. - Page 8 Swing Barrier • User Manual Name Function IC/ID card access control, fingerprint, face recognition, code Access control reader, access control device send delay signal to the device turnstile board door signal. Remote control or button to open the door(select the configuration) The control center of the system, when receiving the access control device delay signal, it control motor running so that Main board...
-
Page 9: Function Features
Swing Barrier • User Manual mark, the infrared sensor detects the complete process of the passenger passing through the passage, and issues signal continuously to the main controller board, until the passenger passes through the passage completely. 5) After the passenger passes through the passage completely, the main controller board delivers a signal to the counter, which will increase 1 automatically, ending the passing process. -
Page 10: Equipment Installation
Swing Barrier • User Manual Housing Material 304 stainless steel Power AC220±10% V、50HZ Working voltage DC 24V Motor Brush DC motor 30W -20 ℃ - 60 ℃ Working temperature ≦90%, no condensation Work environment Open signal Passive signals (relay signals, dry contact signals,) Communication RS485 ≦35 person/min... - Page 11 Swing Barrier • User Manual Screw driver and other common wiring A set of hexagon spanner tool Cross screwdriver 6mm Millimeter Open spanner 17-19mm M12x100 Expansion screws 8pcs Impact drill(including D16 and Cable Tester D14 drills) 2) Ensure the installation location and the system composition ,prepare to install after carrying out the system planning;...
-
Page 12: Connection
Swing Barrier • User Manual 5) Move turnstile and drill hole by impact drill, fix Expansion screws 6) Tighten the expansion screw after the functional test is completed 7)Confirm the lane lines, dig line pipe diameter into the appropriate PVC line pipe, each lane will AC220V power line RVV3*1.5mm and 3pcs CAT 5 cable for connect main machine , 1 PCS network cable for access control system (if install other control system according to the actual situation of laying related field the wire) -
Page 13: Debugging Instruction
Swing Barrier • User Manual 2）Access control device connect Access control device send open signal to control board , gate will open immediately ,The relay time of access control device must be set to 0-1 seconds. Enter SW Exit SW SW1 Gnd SW2 Gnd mark：... - Page 14 Swing Barrier • User Manual 2.5 Notice of use If it tests well before installation, then fixed it; before you install and maintain it, please cut off the power; The product must be earthed, and an earth leakage breaker is necessary on the power supply; ...
- Page 15 Swing Barrier • User Manual 3 Board and parameter instruction 3.1 Board instruction Main board The connect board Port Instruction mark +24V Connect to 24V DC power PWR INPUT 24VDC power supply supply BAT+ Connect the 12V battery, BAT INPUT 12V battery input port Auto normally open when power off.
- Page 16 Swing Barrier • User Manual Fire alarm input Close immediately when cancel Connect to access device Auto SW1 Enter open signal input NO-SW1 COM-Gnd Connect to access device Auto SW2 Exit open signal input NO-SW1 COM-Gnd COM1（485） RS485 communication Protocol docking B－...
-
Page 17: Parameter Instruction
Swing Barrier • User Manual Motor output vice Connect to motor of vice (14) M2 output machie machine +24V 3.3 Parameter instruction Description: the factory has been set up parameters, please do not modify, if you need to modify the parameters, please proceed under technical guidance. 1. - Page 18 Swing Barrier • User Manual 1.10 Pass End Set IR Check passage end position 1. exit (default), 1 safety 1.11 Intrude Set Set Intrude Alarm Mode 1.no alarm, 2 .alarm (default), 3. alarm and close Set Passage From Reverse Alarm Mode 1.12 Reverse Set.
-
Page 19: Trouble Shooting And Maintenance
Swing Barrier • User Manual Set the baud rate of the RS485 2.5 RS485 Baud Reset all setting to factory default. 2.6 Reset Restart controller 2.7 Restart 3. Factory Test Open and close door cycle test 3.1 Cycle Test Check input interface status 3.2 Input Check Output interface test 3.3 Output Test... -
Page 20: Maintenance
Swing Barrier • User Manual Answer：Exchange the connect wire of indicator D1 to D2. Fault 5: Motor idling? Answer： 1） Check whether the POS Sensor connect wires are loose;2） Turn off the power and use the millimeter to check whether the connection between the master machine and the vice machine is continuous.3）Check the vice board 12VGND for voltage output Fault 6: there is one side of barrier is not closed? Answer：1)Check whether the POS Sensor connect wires are loose;2)Turn off the power and use... - Page 21 Swing Barrier • User Manual 2. Rust removal and Lubrication: Check the movement of the flap /slide gate and swing gate, remove rust with sand paper and spread with anti-rust oil if corroded; 3. Screws fastening: Check the connection of the various moving parts, fasten the screws where they are loose to avoid causing fault for long-running;...