Page 5
Licenses THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO.
9.0 TECHNICAL SPECIFICATIONS STRONG declares that the device SRT 8541FTA complies with the basic requirements and other relevant regulations of directives EMC 2014/30/EU, LVD 2014/35/EU and RoHS 2011/65/EU. Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change.
1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: To direct sunlight or any other equipment that generates heat;...
USB 2.0 specifications, recording, playback and other multimedia functions of the receiver might not work properly. STRONG cannot guarantee the playback of files although extensions are listed, as it depends on codec, data bit rate and resolution used (all MPEG codec formats are supported).
2.0 YOUR RECEIVER 2.1 DEFAULT PIN: 0000 2.2 Front Panel Fig. 1 1. IR Sensor Receives commands from the remote control 2. LED Display Shows channel number and time in standby 3. Mode Indicator LED RED indicates that the receiver is in STANDBY mode. 4.
13. OK Opens the current channel list in menu: for confirmation 14. MENU Opens the main menu, in a menu you will get one step back. 15. Exits from the menu or sub-menu. 16. VOL+/VOL- Increases/decreases the volume level. 17.
3.0 CONNECTION 3.1 Connecting to a terrestrial antenna Fig. 6 To receive broadcast signals, your terrestrial indoor or outdoor antenna must be connected to the ANT IN connector on the back of the receiver. Use a proper shielded antenna cable and suitable connectors.
3.7 Extended connections for your home entertainment Fig. 8 Connecting to a Digital Audio Amplifier with S/PDIF By connecting your receiver to a digital amplifier or home cinema set, you can enjoy the best possible sound quality and multi-channel audio (depending on broadcast). Connect your Digital Audio Amplifier or home cinema set with a suitable cinch cable to the S/PDIF connector on the back of the receiver.
5.0 QUICK GUIDE TO USING YOUR RECEIVER We at STRONG understand that you can’t wait to enjoy your new high definition digital terrestrial receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your receiver.
6.0 OPERATION Your new receiver is equipped with several features to make watching TV a true pleasure. This paragraph describes these features. Please do also read chapter 7.0 to get familiar with the menu of your receiver. 6.1 Changing channels Following ways are possible for changing channels with your new receiver: Via direct access using the 0~9 buttons.
select a stream and confirm with OK. The audio channel as stereo, mix, left and right can be selected with t u. 6.4 Teletext Your receiver includes a fully featured Teletext. To access Teletext, press TEXT in viewing mode and use the 0~9 buttons to enter the number of the page you wish to see.
If the channel is changed timeshifted content will only be accessible from the newly selected channel. 6.7.3 Timer recording There are 2 ways to set a timer: Programming a record timer via the EPG The easiest way to record an event is via the EPG. Press the EPG button to open the EPG, then use pq to select a channel.
Use pq to select Scan mode, and select between Free which will only install Free-to-Air channels or All. This means that channels that are Free-to-Air or scrambled will be searched and stored. Use pq to select Channel No and select the channel number of the frequency you’d like to search. Press OK to open a list to make selection faster.
Page 18
7.2.1 TV Manager This menu allows you to create favourite lists, move channels in order, lock channels with PIN protection and delete channels from the TV list. 7.2.1.1 Adding channels to favourite lists Channels from the TV list can be added to up to 4 different favourite groups. Select Favourite and press OK, select the wanted favourite group and press OK.
highlight is on that channel, press OK. At the right hand side you will find the selection to delete from channel list. When you are ready, press 9 and confirm. 7.2.2 Radio Manager Create favourite lists, move channels in order, lock channels with PIN protection and delete channels from the radio list.
Page 20
on top and bottom of the picture on a 4:3 TV. Combined: shows a mix in- between. Ignore: shows as it is. OSD Transparency: To set the OSD transparency from Opacity ~ 50% with 10% steps. OSD Timeout: Sets the time after which on screen banners and messages disappear. The range is 3~10 seconds.
Page 21
Program Lock: Switch all programme/channels lock to On or Off. If the lock is set in the TV or Radio Manager menu. You can select the lock separately for every channel which you like to protect it with a PIN code. Program Lock age: Choose between: Off Lock None, Lock All, 4 years and up to 18 years.
Event Name: Displays, after you have saved the timer, the event name according to the EPG. This is only possible if EPG is available. When all settings are according to your wishes, use pq to move the highlight to Save and press OK to confirm.
Page 23
Pictures: Enter the folder with picture files. Use pq to select a picture. If the format is supported it shows the picture in the small picture-in-picture screen. Press OK to watch it in full screen mode. RED Option: Before the playback of a picture in full screen, you can setup a slideshow/ diashow.
It is possible to use USB storage devices already formatted in NTFS. * STRONG cannot guarantee the playback of files although extensions are listed, as it depends on codec, data bit rate and resolution used (all MPEG codec formats are supported).
If the receiver does not work properly after checking it, please contact your dealer or the local Service Hotline or send email to our Support via www.strong.tv. Do NOT try to open or disassemble the receiver. It may cause a dangerous situation and warranty will be void.
Forgotten PIN code Forgotten channel Contact your local Service Hotline lock code or send an email to our Support via www.strong.tv Press INFO on the remote control to After moving the The antenna signals are too receiver to another weak...
Page 27
MP3, FLAC, OGG* Picture view: BMP, JPG* * STRONG cannot guarantee the playback of all files although extensions are listed, as it depends on codec, data bit rate and resolution used (all MPEG codec formats are supported). Connectors ANT IN - IEC Female Ethernet S/PDIF (coax.)