Related Manuals for Strong SRT 6300W
Summary of Contents for Strong SRT 6300W
-
Page 1: User Manual
Digital Wireless Satellite Receiver with Digital Recorder SRT 6300 W Digital Wireless Satellite Receiver SRT 630 WS User Manual SRT 6300 W SRT 6300 W SRT 630 WS... -
Page 2: Table Of Contents
TABLE OF CONTENTS 1.0 INTRODUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Introduction 1.5 Features & Accessories 2.0 YOUR RECEIVER 2.1 Master SRT 6300 W Front Panel 2.2 Master SRT 6300 W Rear Panel 2.3 Slave SRT 630 WS Front Panel 2.4 Slave SRT 630 WS Rear Panel 2.5 Remote Control 3.0 INSTALLATION... - Page 3 6.9 Play Files 6.10 Stop 6.11 Pause 6.12 Slow Motion Playback 6.13 Fast Forwarding and Rewinding 6.14 Bookmark 6.15 Repeat 6.16 Picture In Picture (PIP, Master Only) 6.17 Keyboard 7.0 TURN OFF SYSTEM 7.1 Master 7.2 Slave 8.0 SOFTWARE UPDATE 9.0 SPECIFICATIONS 9.1 Master 9.2 Slave...
-
Page 4: Introduction
1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: To direct sunlight or near any other equipment that generates heat;... -
Page 5: Storage
1.2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep the packaging away from children. When transporting the receiver from one place to another or if you are returning it under warranty make sure to repack the receiver in its original packaging with its accessories. -
Page 6: Features & Accessories
1.5 Features & Accessories SRT 6300 Wireless Digital Satellite Receiver with Digital Recorder MPEG-2 Digital and fully DVB compliant One Master box + two Slave boxes or one Master box + one Slave box For all Free To Air digital TV and Radio programmes 2 Common Interfaces compatible to all major Conditional Access Modules (Cryptoworks, Viaccess, Conax, etc.) 5 000 channels (TV and Radio) programmable... -
Page 7: Your Receiver
Accessories User Manual Remote control units Batteries (AAA type) Warranty Card Note: The batteries should not be recharged, disassembled, electrically short-circuited or be mixed or used with other types of batteries. 2.0 YOUR RECEIVER 2.1 Master SRT 6300 W Front Panel 1. -
Page 8: Slave Srt 630 Ws Front Panel
3. VCR/DVD SCART Connect the VCR SCART to VCR / DVD recorder 4. ANT IN Connect the TV antenna 5. SWITCH Main power switch. 6. VIDEO OUTPUT Video output (yellow) 7. AUDIO-RIGHT OUTPUT Audio output (Red) 8. AUDIO-LEFT OUTPUT Audio output (White) 9. -
Page 9: Slave Srt 630 Ws Rear Panel
2.4 Slave SRT 630 WS Rear Panel 1. AUDIO-RIGHT OUTPUT Audio output (Red) 2. AUDIO-LEFT OUTPUT Audio output (White) 3. VIDEO OUTPUT Video output (Yellow) 4. S-VIDEO OUTPUT Connect the S-Video input of your TV 5. TV SCART Connect the TV SCART to TV SCART input 6. - Page 10 10. SAT Button [SAT] Display the satellite list. 11. TV / STB Button [TV] Change the terrestrial TV and STB mode. 12. PAGE+ Button [PAGE+] Move the selection bar in menu 13. Audio Button [AUDIO] Select Sound Track and LEFT / RIGHT / MONO / STEREO sound.
-
Page 11: Installation
There are some of the most common ways to connect the equipment in this manual There are several ways of connecting the receivers to the existing Audio/TV system. We recommend to choose one of the following setups If you have problems with your connections and need help, contact your STRONG dealer... -
Page 12: Master Srt 6300 W
3.1 Master SRT 6300 W 3.1.1 Connection to TV, VCR and Hi-Fi 1. Connection to the TV with the SCART Cable Connect one end of the SCART cable to the TV SCART socket on the Master and the other end to a SCART socket on the TV. 2. - Page 13 4. Connection to the TV using the RF Cable Connect a terrestrial antenna to RF IN socket on the Master. Connect one end of the RF cable to the RF OUT socket of the Master. Connect the other end to the ANT IN socket on the TV. 5.
-
Page 14: Slave
2. Installing Master with Twin LNB in Satellite Dish The Connection Type in LNB Setup menu should be set to Twin LNB. 3. Installing Master with two separated Twin LNB Satellite Dishes. and DiSEqC switches The Connection Type in LNB Setup menu should be set to Separated. 3.2 Slave 3.2.1 Connection to TV, VCR and HiFi 1. - Page 15 2. Connection to the VCR with the SCART Cable Connect one end of the SCART cable to the VCR SCART socket on the Slave and the other end to a SCART socket on the VCR. 3. Connection to the TV with the CINCH Cable Connect one end (3 connectors) of the CINCH cable to the AUDIO-RIGHT (red), AUDIO- LEFT (white) and the VIDEO output (yellow) sockets on the Slave.
-
Page 16: Wireless Network Configuration
3.3 Wireless Network Configuration Note: If you start using Slave(s), please do the following steps to set-up wireless connection. Otherwise you can skip the following steps. 1. First turn on the Master. If the Master is in standby mode, press the [Standby] key to switch ON the Master. - Page 17 Unregister (Master only) Move the cursor down to the Slave you want to unregister. Press the Unregister [BLUE] button to unregister it. If you want to change wireless configuration, press the [OK] button to enter Wireless Network Configuration menu when the system is booting. In the Wireless Network Configuration menu, you can change Channel Number, Network Name, Network Density in order to get the best quality.
-
Page 18: Quick Start
4.0 QUICK START Press the [POWER] button to turn on the Master. Now, the Info Box will appear on the bottom of the screen for a certain time and then disappear. By pressing [i] button, the Info Box will remain on the screen. -
Page 19: Channel Organizer
5.2 Channel Organizer 5.2.1 Channel Organizer (Master) This menu can be used to sort, edit and delete TV and Radio Services. Note: The default menu is under TV menu, press [TV/RAD] to switch to Radio menu or switch back to TV menu. MENU OPERATION Sort Press Sort [RED] button. -
Page 20: Favourite Organizer
5.3 Favourite Organizer This mode is helpful in organizing your favourite channels. There are four buttons you can use: sort, next, edit and delete. Note: The default menu is under TV favourite channel menu, you can press [TV/RAD] to switch to Radio favourite channel menu or switch back to TV menu. Sort Press [RED] button. -
Page 21: Timer Setup
5.4 Timer Setup Timer information can be found in menu Timer Setup. To insert a new Timer entry, press [RED] button. Press Modify [GREEN] button to edit the entry. By pressing Delete [YELLOW] button you delete the selected entry. OT = One Time D = Daily W = Weekly R = Record... -
Page 22: Installation
5.5 Installation 5.5.1 System Setup 5.5.2.1 Language There are different languages available for the menu languages Menu Language It is a selection for changing the language of the main menu. Select the language then the menu will be showing. Note: The supported languages can be changed without any notice. - Page 23 SPDIF Output You can enable or disable the S/PDIF digital output in this menu. VCR Output Select a VCR output Terminal or Automatic. RF Modulator (Master Only) When the Master is connected to the TV set with a RF cable, you may need to select the correct TV standard.
- Page 24 5.5.2.5 System Info You can check the System Model, Software Version, Hardware Version, Loader Version, Manufacturer, Website and Serial Number information. 5.5.2.6 Factory Reset All settings will be reset to factory default values. 5.5.3 LNB Setup (Master Only) The Low Noise Block down Converter (LNB) amplifies the signal received by the satellite dish and lowers the frequency of the signal.
- Page 25 DiSEqC 1.0 has four ports. DiSEqC 1.1 has sixteen ports. Transponder To test your settings you can choose a transponder with a strong signal. If your settings are correct then the level and quality banners should show a signal. Dish Type Choose the Dish Type you use Fixed, DiSEqC 1.2, USALS.
- Page 26 Polarization Choose the type of polarisation, either the Horizontal or the Vertical. Symbol Rate Enter the Transponder’s Symbol Rate by using the numeric buttons on your remote control. Scan Mode You can select only searching free channels or all channels (included scrambling channels). Start Search To start the searching process, press [OK] button at “Start Search”.
- Page 27 Tuner Select You can not change the Tuner here. It is the same Tuner as you choose at LNB Setup menu. Transponder Select a transponder to catch a strong signal. Press [OK] to display the transponder list. Command Mode User mode: The movement is adjustable by single steps.
- Page 28 Satellite Angle This is the orbital position of the selected satellite. Normally this is set automatically but if you wish you can edit it manually with the numerical buttons on the remote control. East or West will be selected with [VOL-/VOL+] buttons.
-
Page 29: Media Base
5.5.10 Software Update In this menu you can update your system by using a USB stick. The Slave(s) must be in the same menu while updating the software. 5.6 Media Base To enter this menu you can press [MEDIA] button or on the main menu move the cursor to this screen button, then press the [OK] button. -
Page 30: Media Base Management
5.7 Media Base Management Enter Media Base Management by pressing [SUB] button in Media Base menu. You can also press [SUB] button to go back to Media base under “Media Base Management” Press [VOL-/VOL+] buttons to switch between DVR/MP3/PIC tab. Note: USB storage device won’t be displayed in this menu. -
Page 31: Common Interface (Master Only)
Stop USB Device first move the cursor to the right column, then press [TV/RAD] button to choose the device you want to stop (if you have more than one device plugged in), then press [YELLOW] button to stop the device. Note: If a USB storage is plugged into a Slave, you can not see the file list under the Master and the other Slave’s Base Transfer menu. -
Page 32: Function Guide
6.0 FUNCTION GUIDE 6.1 Channel List Press [OK] button to see the Channel list, when watching the live programme. The Channel List displays the following: Satellite name Free Channels or Scrambled Channels Transponder an Polarization information [RED] button (only in Master) forcing to switch the channel [GREEN] button you can sort the channel list by alphabets Note: Only Master can switch the channels between different Transponders. -
Page 33: Epg (Electronic Programme Guide)
6.3 EPG (Electronic Programme Guide) To display the information of current and following TV programmes, press the [EPG] button on your remote control. If EPG of programmes is broadcasted, you will see the detailed description of the programmes, start/end time and programme schedules etc. [RED] : Display the current programme schedule and detailed description. -
Page 34: Time Shifting
6.7 Time Shifting 1. To use Time Shifting function, press [GREEN] button to display Time Shifting progress bar and pause the current LIVE programme. Press [RED] button or [GREEN] button once more to continue the current LIVE programme. 2. To go to the desired playback position, press [YELLOW] or [BLUE] button. These functions are valid while the Time Shifting progress bar is displayed. -
Page 35: Play Files
6.9 Play Files DVR File Playing a recorded file, the info box will be seen with the File name, Duration time and the buttons you can use. You can enter the time to jump to the exact time by pressing the numerical keys. Note: Goto function only works when the info box is displayed and you can enter hour: minute: second. -
Page 36: Slow Motion Playback
6.12 Slow Motion Playback 1. To playback in slow forward motion (without sound), press the [ ] button. 2. The slow forward motion can be adjusted by pressing the [ ] button repeatedly. 3. To playback in slow rewind motion (without sound), press the [ ] button. 4. -
Page 37: Repeat
6.15 Repeat In Time Shifting mode Press [AROUND] to start Instant Time Shifting. The start position of the playback go 10 seconds back by pressing [AROUND] button. In DVR play mode Press [AROUND] button to repeat playing the current file. Press [AROUND] button once more to cancel the repeated playback. -
Page 38: Keyboard
6.17 Keyboard The keyboard will be displayed when you change file name, folder name, channel name and favourite group name. There are two keyboards you can use: Standard Keyboard Extended Keyboard Use the Standard keyboard. [RED]: [GREEN]: Use the Extend keyboard. [YELLOW]: Save and exit the keyboard [BLUE]:... -
Page 39: Turn Off System
Although the SRT 6300 W System has stable and convenient software to use, a new system software may be released. To add or modify functions, the system software has to be updated. The latest software and manual will be found at STRONG’s website. www.strong.tv With this menu (only Master), you can update your firmware via USB stick. -
Page 40: Specifications
9.0 SPECIFICATIONS 9.1 Master Double Tuners DVB-S Input / Loop through Connector 75 Ohm, IEC 169-24 Frequency Range 950 ~ 2150 MHz Signal Level input -10 ~ -80 dBm @ 27.5 MS/s LNB Power & Polarization Vertical: +13 V DC Horizontal: +18 V DC Current:... -
Page 41: Slave
A/V & Data In/Out TV-SCART Video CVBS/RGB/Y/C Output Audio L/R Output VCR-SCART Video CVBS/RGB Output Audio L/R Output Video CVBS/RGB Input Bypass Audio L/R Input Bypass S-Video Video S-VIDEO Output RCA A/V Video CVBS Output Audio L/R Output S/PDIF Digital Audio or Dolby AC-3 bitstream Output RS-232C 9 pin CD-SUB type Transfer rate 115.2 kbps... - Page 42 Front Panel & RCU 7 KEYs CH-/+, VOL-/+, MENU, OK, STANDBY 4-digital 7-segment LEDs Time, Service name and other info 3 LEDs Link, Record, Power on/Standby 47 keys A/V & Data In/Out TV-SCART Video CVBS/RGB/Y/C Output Audio L/R Output VCR-SCART Video CVBS/RGB Output Audio L/R Output Video CVBS/RGB Input Bypass...
-
Page 43: Troubleshooting
10.0 TROUBLESHOOTING Occasionally the receiver may hang-up. In that case it is recommended to reset the receiver by disconnecting it from the main power. Wait 30 seconds and connect to main power again, then see if the unit is working as expected. If the receiver does not work properly after checking the trouble shooting section, please contact your dealer. -
Page 44: Environmental Issues
Environmental Issues ENVIRONMENTAL ISSUES STRONG is committed to reducing the impact of its products on the environment. To maximise the benefits of our design enhancements, your co-operation is required. Electronic product recycling Packaging Do not dispose of this product with your When disposing of this domestic rubbish. - Page 45 Environmental Issues...