EWM Taurus 301 Synergic Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.8.7
5.8.8
5.8.9
5.8.10
5.8.11
5.8.12
5.8.13
5.8.14
5.8.15
5.8.16
5.8.17
5.8.18
5.9 TIG welding ..................................................................................................................................70
5.9.1
5.9.2
5.9.3
5.9.4
5.9.5
5.9.6
5.10 MMA welding................................................................................................................................77
5.10.1
5.10.2
5.10.3
5.10.4
5.10.5
5.10.6
5.10.7
5.11 PC Interfaces ...............................................................................................................................80
6 Maintenance, care and disposal .........................................................................................................81
6.1 General.........................................................................................................................................81
6.2 Maintenance work, intervals.........................................................................................................81
6.2.1
6.2.2
6.2.3
6.3 Maintenance work ........................................................................................................................82
6.4 Disposing of equipment................................................................................................................82
6.4.1
6.5 Meeting the requirements of RoHS..............................................................................................82
4
Welding task selection ..................................................................................................38
5.8.7.1 Basic welding parameters .............................................................................38
5.8.7.2 Operating mode.............................................................................................38
5.8.7.3 Choke effect / dynamics ................................................................................39
5.8.7.4 Superpulses ..................................................................................................39
5.8.7.5 Wire burn-back ..............................................................................................40
MIG/MAG operating point .............................................................................................41
5.8.8.1 Selecting the display unit...............................................................................41
5.8.8.2 Accessory components for operating point setting .......................................41
MIG/MAG welding data display ....................................................................................42
rootArc ..........................................................................................................................43
forceArc.........................................................................................................................43
MIG/MAG functional sequences / operating modes.....................................................44
5.8.12.1 Explanation of signs and functions................................................................44
MIG/MAG program sequence ("Program steps" mode) ...............................................54
5.8.13.1 Selection of the program sequence parameter .............................................54
5.8.13.2 MIG/MAG overview of parameters ................................................................55
5.8.13.3 Example, tack welding (non-latched) ............................................................56
5.8.13.4 Example, aluminium tack welding (non-latched special) ..............................56
5.8.13.5 Example, aluminium welding (latched special) .............................................57
5.8.13.6 Example, visible seams (latched super pulse) ..............................................58
Main program A mode ..................................................................................................59
5.8.14.1 Selecting parameters (program A) ................................................................60
Standard MIG/MAG torch .............................................................................................61
Remote control .............................................................................................................61
MIG/MAG automatic cut-out .........................................................................................61
Advanced settings ........................................................................................................62
5.8.18.1 Selecting, changing and saving parameters .................................................62
5.8.18.2 Reset to factory settings................................................................................64
5.8.18.3 The special parameters in detail ...................................................................64
Welding torch and workpiece line connection ..............................................................70
Welding task selection ..................................................................................................71
TIG arc ignition .............................................................................................................71
5.9.3.1 Liftarc ignition ................................................................................................71
Pulses, function sequences ..........................................................................................72
5.9.4.1 Explanation of signs and functions................................................................72
TIG automatic cut-out ...................................................................................................75
TIG program sequence ("Program steps" mode) .........................................................76
5.9.6.1 TIG parameter overview................................................................................76
Connecting the electrode holder and workpiece lead ..................................................77
Welding task selection ..................................................................................................78
Welding current setting .................................................................................................78
Arcforce.........................................................................................................................78
Hotstart .........................................................................................................................79
Antistick.........................................................................................................................79
Parameter overview......................................................................................................79
Daily maintenance tasks...............................................................................................81
Monthly maintenance tasks ..........................................................................................81
Annual test (inspection and testing during operation) ..................................................81
Manufacturer's declaration to the end user ..................................................................82
099-005157-EW501
09.06.2011