Makita PC5010C Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Planer
  5. PC5010C
  6. Instruction manual

Makita PC5010C Instruction Manual

Concrete planer
Hide thumbs Also See for PC5010C:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
Concrete Planer
PC5010C
DOUBLE INSULATION
Read before use.

Advertisement

Table of Contents
loading

Related Manuals for Makita PC5010C

Summary of Contents for Makita PC5010C

  • Page 1 INSTRUCTION MANUAL Concrete Planer PC5010C DOUBLE INSULATION Read before use.

  • Page 2: Specifications

    SPECIFICATIONS Model: PC5010C Applicable cup-type diamond wheel Max. wheel diameter 125 mm Spindle thread M14 or 5/8″ (country specific) Max. spindle length 23 mm No load speed (n ) / Rated speed (n) 9,000 min Overall length 350 mm Net weight 2.7 kg...

  • Page 3: Ec Declaration Of Conformity

    Vibration emission (a ) : (m/s ) Uncertainty (K) : (m/s PC5010C NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with another. NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.
  • Page 4 Prevent unintentional starting. Ensure the Store idle power tools out of the reach of chil- switch is in the off-position before connecting dren and do not allow persons unfamiliar with to power source and/or battery pack, picking the power tool or these instructions to operate up or carrying the tool.
  • Page 5 The rated speed of the accessory must be at 15. Regularly clean the power tool’s air vents. The least equal to the maximum speed marked on motor’s fan will draw the dust inside the housing the power tool. Accessories running faster than and excessive accumulation of powdered metal their rated speed can break and fly apart.

  • Page 6: Functional Description

    Additional Safety Warnings: FUNCTIONAL Always install the dust collecting wheel guard before operation. DESCRIPTION Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in CAUTION: Always be sure that the tool is wheel breakage.

  • Page 7: Overload Protector

    Switch action Speed adjusting dial The rotation speed of the tool can be changed by turn- CAUTION: Before plugging in the tool, always ing the speed adjusting dial. The table below shows check to see that the slide switch actuates prop- the number on the dial and the corresponding rotation erly and returns to the "OFF"...
  • Page 8 Loosen the attaching screw on the dust collecting ASSEMBLY wheel guard until attaching slot opens. CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing loop handle CAUTION: Always install the loop handle before operation.
  • Page 9 Fig.12 When you wish to perform clean concrete-planing operation, connect a Makita vacuum cleaner to your tool. Then connect a hose of the vacuum cleaner to the nozzle as shown in the figure.

  • Page 10: Operation

    Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 10 ENGLISH...

  • Page 11: Optional Accessories

    OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885650B226 www.makita.com 20220405...

Table of Contents