Download Print this page
Makita PC5001C Technical Information
Makita PC5001C Technical Information

Makita PC5001C Technical Information

Concrete planer 125mm (5")
Hide thumbs Also See for PC5001C:

Advertisement

T
ECHNICAL INFORMATION
Models No.
Description
C
ONCEPT AND MAIN APPLICATIONS
Models PC5001C and PC5000C are upgraded sister tools
of PC1100. Features electronic control, allowing for
use of powerful 1,400W motor.
Listed below are specification differences between
PC5001C and PC5000C.
Model No.
Auxiliary handle
PC5001C
Top handle
Loop handle,
PC5000C
D-shaped
S
pecification
Voltage (V)
110
120
220
230
240
Model No.
Type
Diameter: mm (")
Wheel
Hole diameter: mm (")
No load speed: min.
Constant speed control
Soft start
Electronic current limiter
Anti-restart function
LED indication lamp
Built-in dust extraction
Protection against electric shock
Power supply cord: m (ft)
Net weight: kg (lbs)
Weight according to
EPTA-Procedure 01/2003: kg (lbs)
S
tandard equipment
Offset diamond wheel 125mm (5") ........ 1 pc
Hex wrench 5 .......................................... 1 pc
Dust bag assembly .................................. 1 pc
Note: The standard equipment for the tools shown above may vary by country.
O
ptional accessories
PC5001C
Offset diamond wheel 125mm (5")
Offset diamond wheel 110mm (4-3/8")
Brush set (includes Brush A and Brush B)
PC5001C, PC5000C
Concrete Planer 125mm (5")
Base and Front roller
Yes
No
Cycle (Hz)
Current (A)
13
50/60
10
50/60
6.7
50/60
6.4
50/60
6.1
50/60
rpm
-1 =
H
W
Continuous Rating (W)
Input
1,400
---
1,400
1,400
1,400
PC5001C
Offset diamond wheel
125 (5)
22.23 (7/8)
10,000
Double insulation
5.0 (16.4)
4.5 (9.9)
5.1 (11.2)
Lock nut wrench ............... 1 pc
Brush set (for spare) ......... 1 set
Steel carrying case ............ 1 pc
PC5000C
Offset diamond wheel 125mm (5")
Brush set (includes Brush A and Brush B)
L
H
PC5001C
W
Dimensions: mm (")
PC5001C
Model No.
Length (L)
479 (18-13/16) 437 (17-1/8)
Width (W)
182 (7-1/8)
Height (H)
195 (7-5/8)
Max. Output (W)
Output
1,000
600
1,000
1,000
1,000
PC5000C
Yes
Yes
Yes
Yes
Yes
Yes
3.4 (7.6)
4.0 (8.9)
PRODUCT
P 1/ 9
L
PC5000C
PC5000C
235 (9-1/4)
2,200
2,200
2,600
2,600
2,600

Advertisement

loading

Summary of Contents for Makita PC5001C

  • Page 1 Models No. PC5001C, PC5000C Description Concrete Planer 125mm (5") ONCEPT AND MAIN APPLICATIONS Models PC5001C and PC5000C are upgraded sister tools of PC1100. Features electronic control, allowing for use of powerful 1,400W motor. PC5001C PC5000C Listed below are specification differences between PC5001C and PC5000C.
  • Page 2: Shoulder Pin

    Ring 60 Supporting Skirt complete when removing Spindle from Spiral bevel gear 35A [2] LUBRICATIONS Apply Makita grease SG.No.0 to the following portions designated with the black triangle to protect parts and product from unusual abrasion. Description Portion to lubricate Amount Item No.
  • Page 3: Assembling

    P 3/ 9 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Armature, Spiral bevel gear 11 (cont.) DISASSEMBLING (2) Disassemble Grip and Base section from the machine as illustrated in Fig. 3. Spiral bevel gear 11 and Armature can be disassembled as illustrated in Fig. 4. Fig.
  • Page 4: Assembling

    P 4/ 9 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Armature, Spiral bevel gear 11 DISASSEMBLING (2-S) If it is difficult to remove Armature by hand; 1) spray some lubricant to M7 Hex nut. 2) turn Armature with water pump pliers while holding M7 Hex nut with wrench 11. Refer to Fig.
  • Page 5: Spring

    P 5/ 9 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Armature, Spiral bevel gear 11 (cont.) ASSEMBLING (1) Assemble Armature to Gear housing as illustrated in Fig. 6. Fig. 6 Assemble Rubber ring 26, Ball bearing 6000DDW Insert Armature into Ball bearing 6000DDW. and Flat Washer 22 to Gear housing.
  • Page 6: Assembling

    P 6/ 9 epair [3] DISASSEMBLY/ASSEMBLY [3]-2. Skirt section (Spiral bevel gear 35A, Ball bearings, Spindle) (cont.) DISASSEMBLING (2) Remove the damaged Ball bearing 6202DDW as illustrated in Fig. 8. Note: Disassembling Spindle section causes a damage to Ball bearing 6202DDW. Therefore, do not reassemble the removed Ball bearing 6202DDW.
  • Page 7 P 7/ 9 epair [3] DISASSEMBLY/ASSEMBLY [3] -3. Shaft lock mechanism DISASSEMBLING (1) Remove Front roller and Base section as illustrated in Figs. 2 and 3. (2) Remove skirt complete as illustrated in Fig. 4. But, no need to separate Gear housing from Motor housing. (3) Now, Shaft lock mechanism can be disassembled as illustrated in Figs.
  • Page 8 P 8/ 9 ircuit diagram Fig. D-1 Color index of lead wires' sheath Orange Black White Insulated connector Field Terminal block Brown Lead wire is used for some countries. Controller Pick-up coil Power Blue Lead wire is used for Noise suppressor supply cord some countries.
  • Page 9 Field lead wire (orange) Grip Field lead wire (white) Brush holder Brush holder Pick-up Coil Makita logo side Wiring in Handle Fig. D-5 Wiring under Switch Wiring to Switch (viewing from Handle set (L) side) Put Controller’s lead wire and Field’s Lead wire as illustrated below.

This manual is also suitable for:

Pc5000c