Advertisement
Quick Links
Advertisement
Related Manuals for Makita PC5010CJ
Summary of Contents for Makita PC5010CJ
- Page 1 INSTRUCTION MANUAL Concrete Planer PC5010C DOUBLE INSULATION Read before use.
- Page 2 SPECIFICATIONS Model: PC5010C Wheel diameter 125 mm Max. wheel thickness 7.2 mm (When using as a grinder) Spindle thread M14 or 5/8″ (country specific) Rated speed (n) 9,000 min Overall length 350 mm Net weight 2.5 - 3.6 kg Safety class •...
- Page 3 Personal Safety SAFETY WARNINGS Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or General power tool safety warnings under the influence of drugs, alcohol or med- ication.
- Page 4 Power tool use and care Do not use accessories which are not specifi- cally designed and recommended by the tool Do not force the power tool. Use the correct manufacturer. Just because the accessory can power tool for your application. The correct be attached to your power tool, it does not assure power tool will do the job better and safer at the safe operation.
- Page 5 14. Regularly clean the power tool’s air vents. The Wheels must be used only for recommended appli- motor’s fan will draw the dust inside the housing cations. For example: do not grind with the side of and excessive accumulation of powdered metal cut-off wheel.
- Page 6 If the use of a guard is recommended for wire brush- FUNCTIONAL ing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in DESCRIPTION diameter due to work load and centrifugal forces. Additional Safety Warnings: Always install the dust collecting wheel guard CAUTION:...
- Page 7 Speed adjusting dial Unintentional restart proof The rotation speed of the tool can be changed by turning the The tool does not start with the switch being lock-on speed adjusting dial. The table below shows the number on even when the tool is plugged. the dial and the corresponding rotation speed.
- Page 8 For offset diamond wheels that are 4 mm or thinner, place the convex section of the lock nut upwards and attach to the spindle. WARNING: Be sure to use a genuine Makita offset diamond wheel. CAUTION: When installing a diamond wheel, always make sure to tighten the lock nut firmly.
- Page 9 Use of damaged brush could lead to injury by When you wish to perform clean concrete-planing leaking dust. operation, connect a Makita vacuum cleaner to your Always install the auxiliary handle on the tool before tool. Then connect a hose of the vacuum cleaner to the operation.
- Page 10 Planing in the corners Installing attachments To plane corners, remove front-edge cover by sliding in CAUTION: Always be sure that the tool is the directions of the arrows as shown in the figure. switched off and unplugged before carrying out any work on the tool.
- Page 11 Installing or removing depressed To remove wheel guard, follow the installation proce- dure in reverse. center wheel or flap disc Optional accessory WARNING: When using a depressed center wheel or flap disc, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
- Page 12 Mount inner flange, abrasive wheel and Ezynut onto the spindle so that Makita Logo on Ezynut faces outside. ► 1. Arrow 2. Notch ► 1. Ezynut 2. Abrasive wheel 3. Inner flange 4.
- Page 13 Installing or removing abrasive disc Optional accessory Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an ► 1. Sanding lock nut 2. Abrasive disc 3. Rubber pad angle of about 15°...
- Page 14 Operation with wire wheel brush Operation with abrasive cut-off / diamond wheel Optional accessory Optional accessory CAUTION: Check operation of wire wheel brush by running tool with no load, insuring that WARNING: When using an abrasive cut-off no one is in front of or in line with the wire wheel / diamond wheel, be sure to use only the special brush.
- Page 15 To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by ► 1. Hook Makita Authorized or Factory Service Centers, always using Makita replacement parts. 15 ENGLISH...
- Page 16 The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. •...
- Page 17 125 mm (5″) model Lock nut / Ezynut *1*2 Back up pad Flex wheel Rubber pad 115 Abrasive disc Sanding lock nut Wire wheel brush Wire cup brush Wheel Guard (for cut-off wheel) *3 Abrasive cut-off wheel / Diamond wheel Lock nut wrench NOTE: *1 Only for tools with M14 spindle thread.
- Page 20 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885650-226 www.makita.com 20180313...