1. Manuals
  2. Brands
  3. MINN KOTA Manuals
  4. Engine
  5. RIPTIDE TERROVA
  6. Owner's manual

MINN KOTA RIPTIDE TERROVA Owner's Manual

Bow-mount trolling motor
Hide thumbs Also See for RIPTIDE TERROVA:
Table of Contents

Advertisement

Quick Links

Download this manual
RIPTIDE TERROVA
BOW-MOUNT TROLLING MOTOR
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for MINN KOTA RIPTIDE TERROVA

Summary of Contents for MINN KOTA RIPTIDE TERROVA

  • Page 1 RIPTIDE TERROVA BOW-MOUNT TROLLING MOTOR Owner's Manual...
  • Page 2 Thank you for choosing Minn Kota. We believe that you should spend more time fishing and less time positioning your boat. That’s why we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought out and rethought until it’s good enough to bear our name.

  • Page 3: Table Of Contents

    WARRANTY ..........................5 KNOW YOUR BOAT ........................6 FEATURES ..........................7 INSTALLATION ......................... 8 Installing the Riptide Terrova .................... 9 Advanced GPS Navigation ..................... 13 Routing the Advanced GPS Navigation Cable .............. 13 Critical Cable Routing ....................13 Considerations for Connecting and Routing Advanced GPS Navigation ......14 Installing the Prop ......................

  • Page 4: Safety Considerations

    WARNING You are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an accurate and reliable tool that will enhance boat operation and improve your ability to catch fish. This product does not relieve you from the responsibility for safe operation of your boat.

  • Page 5: Warranty

    Minn Kota Limited Two-Year Warranty on the Entire Product JOME warrants to the original retail purchaser only that the purchaser’s new Minn Kota saltwater trolling motor will be materially free from defects in materials and workmanship appearing within two (2) years after the date of purchase. JOME will (at its option) either repair or replace, free of charge, any parts found by JOME to be defective during the term of this warranty.

  • Page 6: Know Your Boat

    KNOW YOUR BOAT Port Port Starboard Starboard Inboard Inboard Outboard Outboard Keel Keel Port Port Starboard Starboard Gunwale Gunwale Transom Transom Stern Stern Gunwale Gunwale Stern Stern Hull Hull 6 | minnkotamotors.com ©2022 Johnson Outdoors Marine Electronics, Inc.

  • Page 7: Features

    BATTERY METER TEST WITH MOTOR OFF Power Power TEST Button Button Adjustable Adjustable Depth Collar Depth Collar RIPTIDE TERROVA Indicator Indicator Depth Collar Knob Depth Collar Knob Panel Panel Steering Housing Steering Housing Stow Deploy Lever Stow Deploy Lever Fall Away Ramps...

  • Page 8: Installation

    INSTALLING THE RIPTIDE TERROVA Your new Riptide Terrova comes with everything you’ll need to directly install it to the boat. This motor can be directly mounted to the boat or coupled with a Minn Kota quick release bracket for ease of mounting and removal. For installation with a quick release bracket, refer to the installation instructions provided with the bracket.

  • Page 9: Installing The Riptide Terrova

    INSTALLING THE RIPTIDE TERROVA MOUNTING CONSIDERATIONS It is recommended that the motor be mounted as close to the centerline of the boat as possible. Make sure the area under the mounting location is clear to drill holes and install View accessories nuts and washers.
  • Page 10 INSTALLING THE RIPTIDE TERROVA Remove the Right Sideplate. Swing the Left Sideplate out and away from the Base Extrusion. Base Extrusion Base Extrusion Left Sideplate Left Sideplate Right Sideplate Right Sideplate Make sure that the Power Cables from the battery...
  • Page 11 INSTALLING THE RIPTIDE TERROVA ITEM(S) NEEDED #4 x 6 When the motor is in the deployed position, make sure that the Shaft is 1-1/2" out past the Gunwale of the boat. The lower unit, when stowed and deployed must not encounter any obstructions.
  • Page 12 INSTALLING THE RIPTIDE TERROVA ITEM(S) NEEDED #1 x 6 #4 x 6 #2 x 6 #3 x 6 Put a 1/4-20 x 3 1/2" (Item #1) Screw into each of Screw Screw the drilled locations. The Screw should pass through the Base Extrusion and the boat deck.

  • Page 13: Advanced Gps Navigation

    ROUTING THE ADVANCED GPS NAVIGATION CABLE Your Minn Kota trolling motor and Humminbird fish finder communicate with each other to change the way you fish. Advanced GPS Navigation offers a large array of features including controlling speed, steering, Spot-Lock, and the ability to record and retrace paths on the water, all at your fingertips.

  • Page 14: Considerations For Connecting And Routing Advanced Gps Navigation

    Ethernet connection. ETHERNET CABLES - Minn Kota provides one 30 ft Ethernet cable (AS EC 30E - 30' Ethernet Cable - 720073-4) with every trolling motor equipped with Advanced GPS Navigation.
  • Page 15 ADVANCED GPS NAVIGATION GPS Ethernet Connection Control Control Head Head To Helix To Helix Helix Adapter Cable Helix Adapter Cable Advanced Advanced (provided if needed) (provided if needed) Ethernet Ethernet Connector Connector Ethernet Cable Ethernet Cable (provided) (provided) Directly Directly Coil Cord Coil Cord to Solix...
  • Page 16 ADVANCED GPS NAVIGATION ITEM(S) NEEDED #12 x 1 Identify the keyed Receptacle on the Ethernet Receptacle Receptacle Eight Pin Eight Pin Cable (Item #12). It will be keyed to fit with the Eight Connector Connector Pin Advanced GPS Ethernet Connector below the Control Head.
  • Page 17 “Critical Cable Routing” section of this document Ethernet Cable Ethernet Cable for more details. Ethernet Cable Ethernet Cable Advanced Advanced NOTICE: Minn Kota recommends routing the Ethernet Critical Critical Cable through the Coil Cord when making the Ethernet Cable Cable Ethernet Ethernet Routing Routing connection.
  • Page 18 Cable Cable Helix Adapter Cable Helix Adapter Cable Cable to secure the connection. NOTICE: Minn Kota provides one Helix Adapter Cable (AS EC QDE - Ethernet Adapter Cable - 720074-1) with every trolling motor equipped with Advanced GPS Navigation. Ethernet...

  • Page 19: Installing The Prop

    INSTALLING THE PROP Installing the Prop CAUTION Prop Prop Drive Drive Washer Washer Prop Prop Disconnect the motor from the battery before beginning any prop work or maintenance. While holding the Shipping Spacer with a pliers or vise grip, remove the Prop Nut, Red Shipping Washer, Prop Washer and Spacer, being careful Shipping Shipping...
  • Page 20 INSTALLING THE PROP Holding the end of the Armature Shaft with a Flat Blade Screwdriver, tighten the Prop Nut with a 9/16" Box End or Open End Wrench. Prop Nut Prop Nut Tighten the Prop Nut 1/4 turn past snug to Prop Washer Prop Washer 25-35 in-lbs.

  • Page 21: Battery & Wiring Installation

    CAUTION These guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional electrical devices from the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are using wire longer than that provided with your unit, follow the conductor gauge and circuit breaker sizing table below.

  • Page 22: Selecting The Correct Batteries

    (flooded, AGM or GEL). Lithium-Ion batteries maintain higher voltages for longer periods of time than lead-acid. Therefore, running a Minn Kota trolling motor at speeds higher than 85% for a prolonged period could cause permanent damage to the motor.

  • Page 23: Connecting The Batteries

    Additional Accessories Connected to Trolling Motor Batteries Significant damage to your Minn Kota motor, your boat electronics, and your boat can occur if incorrect connections are made between your trolling motor batteries and other battery systems. Minn Kota recommends using an exclusive battery system for your trolling motor.

  • Page 24: Connecting The Batteries In Series

    CONNECTING THE BATTERIES IN SERIES CONNECTING THE BATTERIES IN SERIES (IF REQUIRED FOR YOUR MOTOR) 24-Volt Systems Two 12-volt batteries are required. The batteries must be wired in +24 Volts to trolling motor series, only as directed in the wiring diagram, to provide 24 volts. To trolling motor negative positive (or circuit breaker) 1.
  • Page 25 CONNECTING THE BATTERIES IN SERIES 36-Volt Systems Three 12-volt batteries are required. The batteries must be wired in series, only as directed in the wiring diagram, to provide 36 volts. Make sure that the motor is switched +36 Volts to trolling motor off (speed selector on “0”).

  • Page 26: Motor Wiring Diagram

    MOTOR WIRING DIAGRAM RIPTIDE TERROVA The following Motor Wiring Diagram applies to all Riptide Terrova models. Black M- Black B- Black M- Control Head Red M+ Advanced GPS Black Navigation Red B+ Power Switch Black Red M+ Coil Cord White...

  • Page 27: Using & Adjusting The Motor

    Indicator Panel on the When stowing or deploying the motor, keep fingers clear of all Mount. The Riptide Terrova must be manually powered "on" and hinge and pivot points and all moving parts. "off." When the Motor is powered "on," the Power Indicator will be illuminated green .

  • Page 28: Stowing And Deploying The Motor

    ADJUSTING THE DEPTH OF THE MOTOR CAUTION For safety reasons, disconnect the motor from the battery/batteries when the motor is not in use or while the battery/batteries are being charged. If the motor control is left on and the propeller rotation is blocked, severe motor damage can result. AutoPilot The AutoPilot Indicator is located on the Indicator Panel on the Mount.

  • Page 29: Push-To-Test Battery Meter

    TEST WITH MOTOR OFF charge in the battery. It is only accurate when the motor is off. The TEST meter reads as follows: RIPTIDE TERROVA • One light indicates recharge. • Two lights indicate low charge. • Three lights indicate good charge.

  • Page 30: Motor Adjustments

    ADJUSTING THE DEPTH OF THE MOTOR MOTOR ADJUSTMENTS ADJUSTING THE DEPTH OF THE MOTOR Once the boat is on the water, it may be necessary to adjust the Lower Unit up or down to achieve an optimum depth for motor performance.

  • Page 31: Adjusting The Lower Unit For A Secure Stow

    ADJUSTING THE LOWER UNIT FOR A SECURE STOW ADJUSTING THE LOWER UNIT FOR A SECURE STOW When the Motor is stowed, the Lower Unit should rest on the Fall Away Ramps, a part of the Motor Mount. It is recommended to secure the motor using the following instructions to avoid damage to the motor and shaft from vibrations during transport.

  • Page 32: Installing An External Transducer

    INSTALLING AN EXTERNAL TRANSDUCER INSTALLING AN EXTERNAL TRANSDUCER An external transducer is not included with your trolling motor. An external transducer can be installed onto the motor. Mount the External Transducer according to directions provided with the transducer. Control Head Control Head Leave enough slack in the Transducer Cable between the Lower Unit and Control Head to allow...

  • Page 33: Service & Maintenance

    SERVICE & MAINTENANCE PROPELLER REPLACEMENT TOOLS AND RESOURCES REQUIRED • 9/16” Open End Wrench • Flat Blade Screwdriver INSTALLATION Disconnect the motor from all sources of power prior to changing the propeller. Drive Pin Drive Pin Armature Armature Shaft Shaft Hold the propeller and loosen the Prop Nut with a pliers or a wrench.

  • Page 34: General Maintenance

    SERVICE & MAINTAINANCE GENERAL MAINTENANCE • After every use, the entire motor should be rinsed with freshwater, then wiped down with a cloth dampened with an aqueous-based silicone spray. Do not spray water into the ventilation openings in the head of the motor. •...

  • Page 35: For Further Troubleshooting And Repair

    Authorized Service Centers Minn Kota has over 800 authorized service centers in the United States and Canada where you can purchase parts or get your products repaired. Please visit our website to locate a service center in your area.

  • Page 36: Compliance Statements

    Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements the WEEE directive. Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of your local town council.
  • Page 37 FCC COMPLIANCE FCC COMPLIANCE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifi cations not expressly approved by Johnson Outdoors Marine Electronics, Inc.

  • Page 38: Parts Diagram & Parts List

    RIPTIDE TERROVA - 55/80/112 LBS THRUST - 12/24/36 VOLT - 54”/60”/72" SHAFT The parts diagram and parts list provides Minn Kota® WEEE compliance disassembly instructions. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased.
  • Page 39 PARTS DIAGRAM & PARTS LIST Control Head Parts List Assembly Part # Description Notes Quantity 2774104 MTR KIT, 4.0 PM SW WR 2770243 CVR KIT, ADV GPS NAV, RT TRV 411690-1 TROLLING MOTOR REMOTE Item Part # Description Notes Quantity SEAL,BUNG LOWER ✖...
  • Page 40 PARTS DIAGRAM & PARTS LIST RIPTIDE TERROVA MOTOR 12 Volt 3.625" Motor Parts Diagram 40 | minnkotamotors.com ©2022 Johnson Outdoors Marine Electronics, Inc.
  • Page 41 PARTS DIAGRAM & PARTS LIST 12 Volt 3.625” Motor Parts List Assembly Part # Description Notes Quantity 2779034 MTR/TUBE ASM 55# 54" RT TRV BT *54"* 2119037 MTR ASY 12V 3.62" 55# SW *60"* 2779307 CTR HSG, CB, 55#, SW 60" 1378170 PROP KIT 2091170 PWR PRP GENII *55LB*...
  • Page 42 PARTS DIAGRAM & PARTS LIST 24 Volt 4” Motor Parts Diagram 42 | minnkotamotors.com ©2022 Johnson Outdoors Marine Electronics, Inc.
  • Page 43 PARTS DIAGRAM & PARTS LIST 24 Volt 4” Motor Parts List Assembly Part # Description Notes Quantity 2777034 MTR/TUBE ASM 80# 54" RT TRV BT *54"* 2777036 MTR/TUBE ASM 80# 60" RT TRV BT *60"* 2777042 MTR/TUBE 80# 72" RT TRV-M BT *72"* 2777398 CTR HSG,CB,80#,SW, UP TO 60"...
  • Page 44 PARTS DIAGRAM & PARTS LIST Item Part # Description Notes Quantity 830-194 THRU BOLT 12-24 X 10.31 COATED 990-051 WASHER - STEEL THRUST 990-052 WASHER - NYLATRON 582-013 CLIP, RETAINING SHORT 973-025 SPACER - BRUSHPLATE 992-010 WASHER - BELLEVILLE 990-045 SPACER - THRUST 788-040 RETAINING RING...
  • Page 45 PARTS DIAGRAM & PARTS LIST 36 Volt 4.5" Motor Parts Diagram minnkotamotors.com | 45 ©2022 Johnson Outdoors Marine Electronics, Inc.
  • Page 46 PARTS DIAGRAM & PARTS LIST 36 Volt 4.5” Motor Parts List Assembly Part # Description Notes Quantity 2777083 MTR/TUBE 112# 60" RT TRV BT *60"* 2777084 MTR/TUBE 112# 72" RT TRV BT *72"* 2777357 CTR HSG ASY,CB,112#,SW,60"TUBE *60"* 2777358 CTR HSG ASY,CB,112#,SW,72"TUBE *72"* 1378160 PROP KIT 2341160 112# WW2...
  • Page 47 PARTS DIAGRAM & PARTS LIST Item Part # Description Notes Quantity 582-016 CLIP-RETAINING, SONAR 992-011 WASHER - BELLEVILLE 990-011 WASHER-SHIM OD 1",ID.630"SS 788-040 RETAINING RING 880-025 SEAL 725-095 PAPER TUBE, SEAL p Not shown on Parts Diagram. ✖ This part is included in an assembly and cannot be ordered individually. minnkotamotors.com | 47 ©2022 Johnson Outdoors Marine Electronics, Inc.
  • Page 48 PARTS DIAGRAM & PARTS LIST RIPTIDE TERROVA STEERING HOUSING Steering Housing Parts Diagram 48 | minnkotamotors.com ©2022 Johnson Outdoors Marine Electronics, Inc.
  • Page 49 PARTS DIAGRAM & PARTS LIST Steering Housing Parts List Assembly Part # Description Notes Quantity 2997056 STR HSG ASM w/BSHG 12V SW *55LB* 2997057 STR HSG ASM w/BSHG 24V SW *80LB* 2997058 STR HSG ASM w/BSHG 36V SW *112LB* 2776562 STEERING HSG TOP SW / GEAR KIT 2777060 STEERING MOTOR KIT, 12V T2...
  • Page 50 PARTS DIAGRAM & PARTS LIST Item Part # Description Notes Quantity 2321510 COLLAR-DRIVE,BOTTOM 2324608 O-RING,224,PD PRO STR HSG 2321515 LINER OUTPUT TUBE 2324604 O-RING, CASE SEAL HOUSING-STEERING, TOP, SW ✖ 2323415 SCREW-#8-32X2.0 SHCS,NYSH 2322601 PIN-LATCH, SS 2321702 WASHER-FLAT .375 NYLON 2263011 E-RING 3/8 DIA.
  • Page 51 PARTS DIAGRAM & PARTS LIST RIPTIDE TERROVA MOUNT Mount Parts Diagram 418 428 minnkotamotors.com | 51 ©2022 Johnson Outdoors Marine Electronics, Inc.
  • Page 52 PARTS DIAGRAM & PARTS LIST Mount Parts List Assembly Part # Description Notes Quantity 2324062 CONTROL BRD ASY, MAIN, 12V, IP *55LB* 2324063 CTRL BRD,MAIN,24/36V,IP *80LB* *112LB* 2994864 BAG ASSY-TERROVA/V2,MNTG HDW Item Part # Description Notes Quantity 2321908 BASE, EXTRUSION, MACH,SW 2322912 PIN-ROLL .1875 X 1.000 SS 2322603...
  • Page 53 PARTS DIAGRAM & PARTS LIST Item Part # Description Notes Quantity 2323403 SCREW-1/4-20 X.375 MCH SS CRPH 2320218 COVER, HANDLE COSMETIC SW 2383446 SCREW-#8-16 X .50" PLASTITE SS 2320830 LOCKING TAB,PWR/BAT.METER 2383428 SCREW-#4-24 X 3/8 HI-LO SS 2090651 LEADWIRE,10 GA 2321310 STRAIN RELIEF 2323405...
  • Page 54 Stop buying new batteries and start taking care of the ones you’ve got. Many chargers can actually damage your battery over time – creating shorter run times and shorter overall life. Digitally controlled Minn Kota chargers are designed to provide the fastest charge that protect and extend battery life. MK212PCL...

Table of Contents