Rechargeable Battery - Fein AKP18-600AS Series Manual

1 609 92A 7RW • 12.1.23 • T
en
16
Total vibration values a
uncertainty K determined according to
EN 62841-1: a <2.5 m/s
h
The vibration level and noise emission value
given in these instructions have been measured
in accordance with a standardised measuring
procedure and may be used to compare power
tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission
value represent the main applications of the
power tool. However, if the power tool is used
for other applications, with different application
tools or is poorly maintained, the vibration level
and noise emission value may differ. This may
significantly increase the vibration and noise
emissions over the total working period.
To estimate vibration and noise emissions accur-
ately, the times when the tool is switched off or
when it is running but not actually being used
should also be taken into account. This may sig-
nificantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect
the operator from the effects of vibration, such
as servicing the power tool and application tools,
keeping their hands warm, and organising work-
flows correctly.

Rechargeable battery

Charging the battery
Use only the chargers listed in the technical
u
data. Only these chargers are matched to the
lithium-ion battery of your power tool.
Note: Lithium-ion rechargeable batteries are
supplied partially charged according to interna-
tional transport regulations. To ensure full re-
chargeable battery capacity, fully charge the re-
chargeable battery before using your tool for the
first time.
Inserting the Battery
Push the charged battery into the battery holder
until it clicks into place.
Removing the Battery
To remove the rechargeable battery, press the
battery release button and pull the battery out.
Do not use force to do this.
The rechargeable battery has two locking levels
to prevent the battery from falling out if the bat-
tery release button is pressed unintentionally.
The rechargeable battery is held in place by a
spring when fitted in the power tool.
Battery charge indicator
The green LEDs on the battery charge indicator
indicate the state of charge of the battery. For
(triax vector sum) and
h
2 2
, K=1.5 m/s .
English
English
English
English
English
safety reasons, it is only possible to check the
state of charge when the power tool is not in op-
eration.
Press the button for the battery charge indic-
ator or to show the state of charge. This is
also possible when the battery is removed.
If no LED lights up after pressing the button for
the battery charge indicator, then the battery is
defective and must be replaced.
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling
of the Battery
English
Protect the battery against moisture and water.
Only store the battery within a temperature
range of −20 to 50 °C. Do not leave the battery in
your car in the summer, for example.
Occasionally clean the ventilation slots on the
battery using a soft brush that is clean and dry.
A significantly reduced operating time after char-
ging indicates that the battery has deteriorated
and must be replaced.
Follow the instructions on correct disposal.
Assembly
English
Inserting the sachet (foil bag)
Remove the battery before carrying out
u
any work on the power tool.
When screwing the barrel for sachets (foil
u
bags)/cartridges into the caulking gun, en-
sure that the barrel for sachets (foil bags)/
cartridges is actually being turned into the
thread. Use your other hand to keep a firm
English
Capacity
60–100 %
30–60 %
5–30 %
0–5 %
English
Capacity
80–100 %
60–80 %
40–60 %
20–40 %
5–20 %
0–5 %
English