Daikin ETSHB16P30EF Installer's Reference Manual page 302

14/16
Field settings table
Breadcrumb Setting name
9.I [D-09] Is an external kWh meter used for power measurement, kWh meter
used for smart grid?
9.I [D-0A] --
9.I [D-0B] --
9.I [D-0C] --
9.I [D-0D] --
9.I [D-0E] --
9.I [E-00] Which type of unit is installed?
9.I [E-01] Which type of compressor is installed?
9.I [E-02] What is the indoor unit software type?
9.I [E-03] What is the number of backup heater steps?
9.I [E-04] Is the power saving function available on the outdoor unit?
9.I [E-05] Can the system prepare domestic hot water?
9.I [E-06] --
9.I [E-07] What kind of DHW tank is installed?
9.I [E-08] Power saving function for outdoor unit.
9.I [E-09] --
9.I [E-0B] Is a bi-zone kit installed?
9.I [E-0C] What bizone system type is installed?
9.I [E-0D] Is the system filled with glycol ?
9.I [E-0E] --
9.I [F-00] Pump operation allowed outside range.
9.I [F-01] Above which outdoor temperature is cooling allowed?
9.I [F-02] --
9.I [F-03] --
9.I [F-04] --
9.I [F-05] --
9.I [F-06] Enable Tank Boiler?
9.I [F-07] Efficiency calculation
9.I [F-08] Continuous heating defrost enable
4P681797-1 - 2022.01
Range, step
Default value
R/W 0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
6: 100 pulse/kWh (PV meter)
7: 1000 pulse/kWh (PV meter)
0
2
0
0
0
R/O 0~5
0: LT split
R/O 1
R/W (*1) 0: Reversible (*1)
R/O (*2) 1: Heating only (*2)
R/W 0: no heater (*7)
2: 3V (*4)
3: 6V (*5)
4: 9W (*6)
R/O 0: No
1: Yes
R/O 0: No
1: Yes
1
R/W 0~8
0 OSO tank 150/180
1 FS with BUH
2 FS with BSH
3 OSO tank 200/250/300
4 Rotex without BSH (HYB)
5 Rotex with BSH
6 Third party tank for HYB
7 Third party tank, coil >= 1,05m2
8 Third party tank, coil >= 1,8m2
R/W 0: No
1: Yes
1
R/W
0: not installed
1: -
2: Bizone kit installed
R/W
0: Without hydraulic separator / no
direct pump
1: With hydraulic separator / no direct
pump
2: With hydraulic separator / with direct
pump
R/W
0: No
1: Yes
0
R/W 0: Restricted
1: Allowed
R/W 10~35°C, step: 1°C
20°C
3
5
0
0
R/W
0: Disabled
1: Enabled
R/W 0: Enabled
1: Disabled
R/W
0: Disabled
1: Enabled
(*6) *EKECBUA*3V_(*7) *EKECBUA*6V_(*8) *EKECBUA*9W_(*9) BUH less_
Installer setting at variance with
default value
Date Value
(*1) 300 Tank_(*2) 500 Tank_
(*3) *X*_(*4) *H*_(*5) *B*_
(*10) 16P