Table of Contents
Advertisement
ª To Display Date/Time Indication
To display Date/Time Indication, set the appropriate Date/
Time in [DATE/TIME] on the [DISPLAY SETUP] Sub-Menu.
(l 13)
You also can press the [DATE/TIME] Button of the Remote
Controller repeatedly to display or change the Date/Time
Indication.
ª To Change the Display Mode
By changing [DISPLAY] on the [DISPLAY SETUP] Sub-
Menu, you can change the Display Mode to All Function
Display [ALL], Partial Display [PARTIAL], and Minimum
Display [OFF].
~~~~~~~~~~~~~~~~~~~
Warning/Alarm Indications
If any one of the following indications lights up or flashes,
please check the condition of the Movie Camera.
≥Some Indications may not be displayed according to the
model.
3:
Condensation has occurred. (l 43)
Y:
The accidental erasure prevention
slider on the inserted Cassette is
open (that is, set to [SAVE].)
You are about to do audio dubbing
on the unrecorded (blank) portion of
the tape.
No Cassette is inserted. (l 11)
6:
The Battery is low.Recharge it.
(l 10)
0:
The button-type battery is low or not
in. (l 17)
::
The video heads are dirty. (l 44)
2END:
The tape came to end during
recording.
REMOTE:
Wrong Remote Controller Mode has
been selected. (l 9)
PRINTER ERROR:
The Video Printer is not connected
correctly, or the Video Printer is not
functioning properly.
UNPLAYABLE TAPE
(OTHER FORMAT):
You are attempting to play back a
tape section that has been recorded
with a different TV system.
UNABLE TO A. DUB
(LP RECORDED):
Because the original recording was
done in LP Mode, audio dubbing
cannot be performed.
INCOMPATIBLE
TAPE:
This Cassette is incompatible.
PLEASE RE-OPERATE
AFTER PUSHING
RESET BUTTON:
Mechanism Irregular is detected.
Press the [RESET] Button (l 6).
This may solve the problem.
TO SERVICE:
It is a malfunction.
CARD FULL:
Card does not have sufficient
memory remaining.
NO CARD:
Card is not inserted.
NO PICTURE:
Card has no pictures recorded on it.
CARD ERROR:
This Card is not compatible with this
Movie Camera.
COPY INHIBITED:
Because the medium is protected by
a copy guard, images cannot be
recorded correctly.
~~~~~~~~~~~~~~~~~~~
Notes and Hints
ª Concerning the Power Supply
≥When the Movie Camera is used for a long time, the
Camera body becomes warm, but this is not a malfunction.
≥If the [CHARGE] Lamp does not light up although the
Battery is attached to AC Adaptor, detach the Battery and
reattach it.
≥Battery CGP-D110 and CGP-D105 cannot be charged with
this AC Adaptor.
ª Inserting/Removing the Cassette
≥In the case of using a previously recorded Cassette, you
can use the Camera Search Function to find the position
where you want to continue recording.
≥If a new Cassette is inserted, rewind to the beginning of the
tape before starting recording.
≥When inserting the cassette, make sure it faces in the right
direction and then push it in until it stops.
≥When opening or closing the Cassette Compartment, push
down the buckle of the Grip Belt so that it does not
obstruct the opening and closing of the Cassette
Compartment.
ª Alarm Sounds
When [BEEP SOUND] on the [OTHER FUNCTIONS] Sub-
Menu on the [CAMERA FUNCTIONS] Main-Menu is set to
[ON], confirmation/alarm beeps are issued as follows.
1 Beeps
≥When you start recording
≥When you switch the [OFF/ON] Switch from [OFF] to [ON]
2 Beeps
≥When you pause recording
10 Beeps
≥If you perform a wrong operation before or during recording
ª Recording
≥Before turning on the power, remove the Lens Cap. If the
Lens Cap is still attached when the power is turned [ON],
Automatic White Balance Adjustment (l 47) may not
function correctly.
ª Recording Check
≥For Recording Check, the Movie Camera mode (SP/LP)
must be the same as the mode used for the recording. If
different, playback images will be distorted.
ª Camera Search
≥In Camera Search Mode, images may contain mosaic-
pattern noise. This is a phenomenon that is characteristic
of digital video and not a malfunction.
≥If the recording speed modes (SP/LP) of previous
recording and new recording are different, playback images
may be distorted.
ª Photoshot
≥Photoshot Recording results in slightly inferior image
quality.
ª Progressive Photoshot Function
≥When you change to the Still Picture Mode, you will hear a
click. This is the sound of the iris closing and not an
indication of malfunction.
≥If you record still pictures in Progressive Photoshot Mode
when your Movie Camera is set to Programme AE (l 22),
the brightness of the images may change.
About [PROGRESSIVE] Setup
≥When the [æ] Indication is displayed, you can use the
Progressive Photoshot Function.
When [PROGRESSIVE] is [ON]:
You can use the Progressive Photoshot Function at any time.
In this case, however, the following functions are disabled.
≥Digital Effect Modes in [EFFECT1] (l 25)
39
Hide quick links:
Advertisement
Table of Contents
