Table of Contents
Advertisement
ß
:
Video Flash (setting to [AUTO])
A
:
Video Flash turned off (when lighted yellos,
the Flash Sensor determined that the light is
needed)
-22-
£:
Red Eye Reduction
ª To Change the Counter Display Mode
By changing [C.DISPLAY] on the [DISPLAY SETUP]
Sub-Menu, you can change the Counter Display Mode to
Tape Counter Indication [COUNTER] (0:00.00), Memory
Counter Indication [MEMORY] (M0:00.00), and Time Code
Indication [TIMECODE] (0h00m00s00f). (
pressing the [COUNTER] Button on the Remote Controller,
you can change the Counter Display Mode.
ª To Display Date/Time Indication
To display Date/Time Indication, set the appropriate
Date/Time in [DATE/TIME] on the [DISPLAY SETUP]
Sub-Menu. (
)
-12-
You can also press the [DATE/TIME] Button of the Remote
Controller repeatedly to display or change the Date/Time
Indication.
ª To Change the Display Mode
By changing [DISPLAY] on the [DISPLAY SETUP]
Sub-Menu, you can change the Display Mode to All Function
Display [ALL], Partial Display [PARTIAL] and Minimum
Display [OFF]. (
)
-12-
Owner ID
You can register your name and address in your Movie
Camera to identify the owner.
1
Set [CAMERA FUNCTIONS] >> [OTHER FUNCTIONS]
>> [OWNER ID SET] >> [YES].
≥The [OWNER ID] Menu appears.
2
(26)
Turn the [PUSH] Dial
press the [PUSH] Dial
(26)
3
Turn the [PUSH] Dial
(26)
the [PUSH] Dial
(26)
to enter them.
≥You can input 4 digits.
4
Press the [∫] Button.
5
Repeat Steps 2–4 to input desired characters for
[NAME]/[HOUSE No.]/[POSTCODE].
≥You can input up to 12 characters in [NAME], and up to
11 characters in [HOUSE No.] and [POSTCODE].
6
Press the [∫] Button to finish the setup.
To verify Owner ID
Keep pressing the [;] Button for approximately 5 seconds.
To Check Owner ID
If Owner ID has already been set, carrying out Step 1 will
display [INPUT PIN NUMBER] on the screen. Input the Pin
Number you have already selected. If the number is not
correct, the screen will not change. If the number is correct,
the contents of the setup will be displayed. (By repeating
Steps 2 to 4, you can change the contents.)
Warning/Alarm Indications
If any one of the following indications lights up or flashes,
please check the condition of the Movie Camera.
3: Condensation has occurred.
Y: The accidental erasure prevention slider on the
inserted Cassette is open (that is, set to [SAVE]).
You are about to do audio dubbing on the unrecorded
(blank) portion of the tape.
No Cassette is inserted.
6: The Battery is low. Recharge it.
0: The built-in battery is low.
::
The video heads are dirty.
2END:
The tape came to end during recording.
-22-
,
-45-
-22-
) By repeatedly
-12-
to select [PIN NUMBER] and
to input desired numbers.
to select numbers and press
-49-
-9-
-8-
-14-
-49-
Others
REMOTE:
Wrong Remote Controller Mode has been selected.
UNPLAYABLE TAPE
(OTHER FORMAT):
You are attempting to play back a tape section that has
been recorded with a different TV system.
UNABLE TO A. DUB
(LP RECORDED):
Because the original recording was done in LP Mode,
audio dubbing cannot be performed.
UNABLE TO WRITE
(WIDE MODE):
You are attempting to record a Wide Mode picture on a
tape to a Card.
INCOMPATIBLE TAPE:
This Cassette is incompatible.
PLEASE RE-OPERATE
AFTER PUSHING
RESET BUTTON:
Mechanism Irregular is detected. Press the [RESET]
Button (
). This may solve the problem.
-5-
TO SERVICE:
It is a malfunction.
CARD FULL:
Card does not have sufficient memory remaining.
Select Card Mode and delete unnecessary files.
NO CARD:
Card is not inserted.
NO FILE:
Card has no files recorded on it.
UNPLAYABLE CARD:
You are attempting to play back a data which is not
compatible with this Movie Camera.
CARD ERROR:
This Card is not compatible with this Movie Camera.
COPY INHIBITED:
Because the medium is protected by a copy guard,
images cannot be recorded correctly.
INCORRECT
OPERATION:
You are attempting to record to a tape in VCR Mode.
You are pressing the [PHOTO SHOT] Button in
MPEG4 Recording or Voice Recording.
You are attempting to record to a tape in Card Mode.
CONNECT USB CABLE:
The [WEB CAMERA] Button is pressed with USB
Cable unconnected. Connect the USB Cable to the
Movie Camera and the Personal Computer.
DISCONNECT USB CABLE:
You are pressing the Recording Start/Stop Button, the
[PHOTO SHOT] Button or the [TITLE] Button in the
WEB CAMERA Mode.
You are pressing the [TITLE] Button in Camera Mode
or VCR Mode with a USB Cable connected.
You are attempting to record on a Card with a USB
Cable connected.
CANCEL WEB CAMERA MODE:
It is not possible to operate the [OFF/ON/MODE]
Selector Switch in the WEB CAMERA Mode.
Notes and Hints
ª Concerning the Power Supply
≥When the Movie Camera is used for a long time, the
Camera body becomes warm, but this is not a malfunction.
≥If the [CHARGE] Lamp does not light up although the
Battery is attached to the AC Adaptor, detach the Battery
and reattach it.
≥Battery CGP-D110 and CGP-D105 cannot be charged with
this AC Adaptor.
-42-
-7-
Advertisement
Table of Contents
