Power Supply; Charging Time And Available Recording Time - Panasonic NV-DS27 Operating Instructions Manual

1
2
1
2
PUSH
NV-DS27/DS28
A
1 h.
B
1 h 50 min. (1 h 30 min.)
C
55 min. (45 min.)
A
1 h 50 min.
B
3 h 10 min. (2 h 40 min.)
C
1 h 35 min. (1 h 20 min.)
A
2 h.
B
4 h. (3 h 15 min.)
C
2 h. (1 h 40 min.)
A
3 h 15 min.
B
7 h. (5 h 40 min.)
C
3 h 30 min. (2 h 50 min.)
A
5 h 20 min.
B
13 h. (10 h 25 min.)
C
6 h 30 min. (5 h 15 min.)
10

Power Supply

ª Using the AC Adaptor
1
2
3
1
3
ª Using the Battery
Before use, fully charge the Battery.
1
2
To Remove the Battery
3
Set the [OFF/ON] Switch
3
, slide the Battery to remove it.
2
OFF ON ª Using the Car Battery Charger
If you use the Car Battery Charger (VW-KBD2E; optional), you can supply
power to the Movie Camera and charge the battery inside your car. For
further information, refer to the instruction manual of the Car Battery Charger.
≥Be sure to start the car engine before you connect the Car Adaptor Cord,
otherwise the fuse may blow.
≥For other notes concerning this item, see page 39.
~~~~~~~~~~~~~~~~~~~~~~~~

Charging Time and Available Recording Time

NV-DS37/DS38
A
1 h.
B
1 h 40 min. (1 h 25 min.)
C
50 min. (45 min.)
(Intermittent Recording Time is the available recording time with repeated
1 h 50 min.
recording and stopping actions.)
2 h 55 min. (2 h 30 min.)
≥"1h10min." indicates 1 hour and 10 minutes.
1 h 30 min. (1 h 15 min.)
≥Battery CGR-D08R is supplied.
2 h. ≥The times shown in the table are approximate times. The numbers in
parentheses indicate the recording time when the LCD Monitor is used.In
3 h 30 min. (3 h.)
actual use, the available recording time may be shorter.
1 h 45 min. (1 h 30 min.)
≥The times shown in the table are for continuous recording at a temperature
3 h 15 min.
of 20oC and humidity of 60%. If the Battery is charged at a higher or lower
6 h 5 min. (5 h 15 min.)
temperature, the charging time may be longer.
3 h 5 min. (2 h 40 min.)
5 h 20 min.
11 h 25 min. (10 h.)
5 h 45 min. (5 h.)
Connect the DC Input Lead to the [DC IN] Socket on the
Movie Camera.
Connect the DC Input Lead to the AC Adaptor.
Connect the AC Mains Lead to the AC Adaptor and the AC
mains socket.
≥The AC Mains Lead's outlet plug cannot be pushed fully into the AC
Adaptor socket. A gap will remain as shown
≥Before disconnecting the power supply, set the [OFF/ON] Switch on the
Movie Camera to [OFF].
Attach the Battery to AC Adaptor and charge it.
≥Since the Battery will not be charged when the DC Input Lead is
connected to the AC Adaptor, disconnect them.
≥The [POWER] Lamp and [CHARGE] Lamp lights up, and charging
starts.
≥When the [CHARGE] Lamp goes off, charging is completed.
Attach the charged Battery to the Movie Camera.
2
to [OFF], and while pressing the [PUSH] Button
Charging Time
Maximum Continuous Recording Time
Intermittent Recording Time
1
.