Table of Contents
Advertisement
Quick Links
FastMig
SF 51, SF 54
Operating manual
Bruksanvisning
Gebrauchsanweisung
Manual de instrucciones
Käyttöohje
Manuel d'utilisation
Manuale d'uso
Gebruiksaanwijzing
Brugsanvisning
Instrukcja obsługi
Manual de utilização
Инструкции по эксплуатации
Bruksanvisning
操作手册
EN
DA
DE
ES
FI
FR
IT
NL
NO
PL
PT
RU
SV
ZH
Advertisement
Table of Contents
Related Manuals for Kemppi FastMig SF 51
Summary of Contents for Kemppi FastMig SF 51
- Page 1 FastMig SF 51, SF 54 Operating manual Bruksanvisning Gebrauchsanweisung Manual de instrucciones Käyttöohje Manuel d’utilisation Manuale d’uso Gebruiksaanwijzing Brugsanvisning Instrukcja obsługi Manual de utilização Инструкции по эксплуатации Bruksanvisning 操作手册...
- Page 3 OPERATING MANUAL English...
-
Page 4: Table Of Contents
..................FastMig SF 51, SF 54... -
Page 5: Preface
This operating manual contains important information on the use, maintenance and safety of your Kemppi product. The technical specifications of the equipment can be found at the end of the manual. -
Page 6: Use
FastMig SF 51 and SF 54 panels are supposed to be used only with synergic powers sources FastMig KMS 300, 400 or 500. SF 51 panel can be mounted to MXF 63 (200 mm wire spool) wire feeder and SF 54 panel to MXF 65 and 67 (300 mm wire spool) wire feeders. -
Page 7: Functions Of Sf 51 And Sf 54 Function Panel
11. a) Adjustment of wire feed speed b) Adjustment of MMA current c) Selection of SETUP parameter 12. a) Welding voltage adjustment b) Adjustment of MIG dynamics c) Adjustment of SETUP parameters 13. Manual control/remote control unit selection © Kemppi Oy / 1515... -
Page 8: Sf 51 And Sf 54 Operations
MIG gun has been connected to the equipment. When liquid cooling is selected, the liquid cooling unit will start up in connection with the next equipment start-up. The selection can also be made through the SETUP function. FastMig SF 51, SF 54... - Page 9 Parameter value is selected from right potentiometer (control knob), and the value can be seen on the right display. (See the information on SETUP functions). © Kemppi Oy / 1515...
-
Page 10: Panel Sf 51 And Sf 54 Setup Parameters
OFF, on Enables water cooler Wire Inch Stop OFF, on OFF = Stops wire inch in case arc does not ignite on = Feeds wire as long as the welding gun start switch is pressed. FastMig SF 51, SF 54... - Page 11 OFF = No reset Restore Factory PAn = Settings will be restored, but OFF, PAn, ALL Settings memory channels remain unchanged ALL = All settings will be restored to factory values Arc Voltage Display function needs activation. NOTE! © Kemppi Oy / 1515...
-
Page 12: Fastmig Error Codes
Gas is unconnected to the wire feeder. Gas has been ran out, gas hose is leaking or there is no pressure enough in the gas web. Connect the gas to the wire feeder, check gas hose and the pressure of the gas web. FastMig SF 51, SF 54... -
Page 13: Disposal
The owner of the equipment is obliged to deliver a decommissioned unit to a regional collection centre, per the instructions of local authorities or a Kemppi representative. By applying this European Directive you will improve the environment and human health. - Page 14 Tel. +61 2 9605 9500 sales.india@kemppi.com DK-2740 SKOVLUNDE Telefax +61 2 9605 5999 DANMARK info.au@kemppi.com KEMPPI WELDING SOLUTIONS SDN BHD Tel +45 4494 1677 No 12A, Jalan TP5A, OOO KEMPPI Telefax +45 4494 1536 Taman Perindustrian UEP, Polkovaya str. 1, Building 6 sales.dk@kemppi.com...
Need help?
Do you have a question about the FastMig SF 51 and is the answer not in the manual?
Questions and answers