CTC Union IGS-803SM-8PH24, IGS-803SM-8PHE24 Quick Installation Guide
- Quick installation manual (2 pages)
Advertisement
Introduction
IGS-803SM-8PH(E)24 are managed industrial grade Gigabit PoE (Power over Ethernet) switches that provide stable and reliable Ethernet transmission. Housed in rugged DIN rail or wall mountable enclosures, these switches are designed for harsh environments, such as industrial networking and intelligent transportation systems (ITS) and are also suitable for many military and utility market applications where environmental conditions exceed commercial product specifications. Standard operating temperature range models (-10°C to 60°C) and wide operating temperature range models (-40°C to 75°C) fulfill the special needs of industrial automation applications.
Features
- Redundant dual DC inputs 24/48VDC
- DCV 'boost' feature; regulated 55VDC PoE output voltage
- IP30 rugged metal housing
- Wide temperature range -40°C~75°C (IGS-803SM-8PHE24)
- Supports many advanced Ethernet L2 functions
- Console, Telnet (ssh), Web and SNMP management
- Industrial grade EMS, EMI; UL60950-1, EN50121-4, EN61000-6-2, EN61000-6-4
Specifications
Ethernet Interface
- Standards: IEEE802.3 (10Base-T), 802.3u (100Base-TX), 802.3ab (1000Base-T)
- RJ-45 (shielded) Ports: 8 ports
- Speed: 10/100/1000M (Auto)
Optical Interface
- • Standards: IEEE802.3u (100Base-FX), 802.3z (1000Base-X), 802.3ab (1000Base-T)
- • 3 ports, SFP based
- • Speed: 100/1000M (Manual)
Switch Features
- Store & Forward Switch
- Supports IEEE802.3x Flow Control
- Auto MDI/MDI-X
- Duplex: Full/Half (Auto-negotiation per IEEE802.3u)
- Switching Fabric: 22Gbps (Non-blocking)
- Packet Buffer: 1Mb
- MAC Table: 8K
- MTU: 64~9600 bytes
Power over Ethernet
- 8 PoE enabled ports, Alternate A Mode
- Supports IEEE802.3af 15.4watts PoE per port
- Supports IEEE802.3at 30watts PoE+ per port (180W budget)
- Positive (VCC+) pins 1,2 (55VDC); Negative (VCC-) pins 3,6
Power
- Absolute Input Range: 20VDC~57VDC
- Reverse Polarity Protection: Yes
- Dual Power Inputs: Yes
- Connector: Removable terminal block
- Consumption:
| Input Voltage | Items | |||
| Total Power Consumption | Device Power Consumption | PoE Budget | Boost Efficiency | |
| 24VDC | 200.2W | 9.2W | 180W | 94% |
| 48VDC | 195.1W | 9.8W | 180W | 97% |
Mechanical
- Water & Dust Proof: IP30 Protection
- Dimensions: 116 mm (D) x 64 mm (W) x 152 mm (H)
- Mounting: DIN-Rail, Wall Mount (Kits included)
- Weight: 970 g
Environmental
- Operating Temperature: -10°C~60°C (IGS-803SM-8PH24)
-40°C~75°C (IGS-803SM-8PHE24) - Storage Temperature: -40°C~85°C
- Humidity: 5%~95% (Non-condensing)
Certifications
- EMC: CE
- EMI (Electromagnetic Interference): FCC, FCC Part 15 Subpart B Class A, CE EN55022 Class A
- Railway Traffic: EN50121-4
- Immunity for Heavy Industrial Environment: EN61000-6-2
- Emission for Heavy Industrial Environment: EN61000-6-4
- EMS (Electromagnetic Susceptibility) Protection Level:
EN61000-4-2 (ESD) Level 3, Criteria B
EN61000-4-3 (RS) Level 3, Criteria A
EN61000-4-4 (Burst) Level 3, Criteria A
EN61000-4-5 (Surge) Level 3, Criteria B
EN61000-4-6 (CS) Level 3, Criteria A
EN61000-4-8 (PFMF, Magnetic Field) Field Strength:
300A/m, Criteria A - Safety: UL60950-1
- Freefall: EN60068-2-32
- MTBF: 311,276 hours (MIL-HDBK-217)
- Shock: EN60068-2-27
- Vibration: EN60068-2-6
Connectors
Front Panel
LAN and Fiber Connection
IGS-803SM-8PH(E)24 PoE switches have 8 electrical LAN ports (labeled 1~8) and 3 fiber ports (SFP based, labeled Fiber 1~3) on the front panel. The LAN ports that utilize shielded RJ-45 connectors support 10/100/1000M; while the fiber SFP ports support 100/1000M.
PoE Ports
All 8 LAN ports support PoE (Power over Ethernet) per IEEE802.3af (15.4W) or IEEE802.3at (30W) for connection to standard PoE PD (Power Devices) such as IP Cameras, Access Points, IP Phones, Digital Signage, etc. PoE eliminates the need to run separate power to these devices thereby simplifying deployment and reducing expenses.
The LAN ports may also connect to any non-PoE device for normal Ethernet transmission without any damage to the nonPoE device or to this device.
RJ-45 Ethernet Port Pinouts
Figure 2. RJ-45 Ethernet Port Pinouts
RJ-45 Ethernet & PoE Pin Assignments
| Pin No. | RJ-45 Ethernet 100Base-TX | PoE Output |
| 1 | RX+ | V+ |
| 2 | RX- | V+ |
| 3 | TX+ | V- |
| 4 | - | |
| 5 | - | |
| 6 | TX- | V- |
| 7 | - | |
| 8 | - |
CONSOLE Port
The RJ-45 port labeled "CONSOLE" is an RS-232 terminal port for local management. These models use a "light" CLI (Command Line Interface) in addition to a user friendly Web interface and industry standard SNMP.
One RJ-45 to DB-9 cable is provided with this device. CONSOLE port pinouts (Figure 2) and RS-232 DB-9 (Figure 3) connector are illustrated below together with RJ-45 to DB-9 signal mapping information. Use the supplied cable to connect the RJ-45 CONSOLE port to a console PC.
Figure 3. CONSOLE Port Pinout
RJ-45 to DB-9 Signal Mapping
| DB-9 (Female) | Direction | RJ-45 | ||
| Signal | Pin | Pin | Signal | |
| RXD | 2 |  | 3 | TXD |
| TXD | 3 |  | 6 | RXD |
| GND | 5 |  | 5 | GND |
Power and Alarm
Terminal Block
Alarm Relay Circuit
A removable terminal block on the top panel provides both power and alarm connections. Power can be provided through the dual inputs from separate sources. The alarm relay contact can be wired into an alarm circuit which senses an alarm condition when the contact is broken. The alarm relay is normally closed when there is no alarm condition. The alarm conditions are user programmable through management to include power, link faults or other fault conditions. Please note that the alarm relay contact can only support 1A current at 24VDC. Do not apply voltage and current that exceed these specifications.
CLI & Web Basic Operation
IGS-803SM-8PH(E)24 are managed Fast Ethernet PoE switch devices. Initial configuration (assignment of IP address) may be accomplished via the RS-232 console and a PC or laptop running terminal emulation software. Configure the terminal as follows:
115200 speed, 8 data bits, no parity, 1 stop bit, no flow control
IGS-803SM-8PH(E)24 PoE switches use a command line interface (CLI) through the serial port. Once the IP address has been configured, a web browser can be used to configure the device through a more easy to use GUI (graphical user interface). Please refer to the operation manual on the CDROM.
Using the provided console cable, connect the RJ-45 to the "CONSOLE" port and the DB9 to PC COM port. Apply power to the switch. At the "Username:" prompt, enter 'admin' (lower case, no quotes). Just press Enter when prompted for password.
To set the IP address and subnet mask issue this command:
> ip address 1 192.168.0.250/24
(example: sets VID 1 to 192.168.0.250, subnet 255.255.255.0)
NOTE: The factory default IP address is 10.1.1.1 with mask 255.255.255.0
LED Indicators
| LED | Color | Definition |
| PWR1/ PWR2 | Green | Power is connected and active at the PWR1/PWR2 input terminal connection. |
| Off | PWR1/PWR2 is not connected. | |
| Fault | Amber | When one or more of the programmable alarm conditions is active. |
| Off | Normal operation without faults. Alarm conditions are all disabled. | |
| CPU ACT | Green | During normal use, this LED will be lit, indicating a healthy condition of the running CPU. |
| Ring Master | Yellow | Lit when this unit is the 'master' in a fiber ring and all units are configured for uRing or ERPS (Ethernet Ring Protection Switching or G.8032). |
| LAN LINK/ACT | Green | The connected LAN speed is 10/100M. |
| Green Blinking | Blinking when there is Ethernet traffic. | |
| Amber | The connected LAN speed is 1000M. | |
| Amber Blinking | Blinking when there is Ethernet traffic. | |
| Off | No Ethernet link. | |
| FIBER LINK/ACT | Green | The fiber link is up. |
| Blinking | Blinking when there is data traffic. | |
| Off | No fiber link. | |
| PoE | Green | The respective LAN port has successfully negotiated PoE and is supplying output power to the remote connected PD. |
| Blinking | One of the PoE faults (overload, short circuit, port failure at startup) occurs. | |
| Off | PD is not connected or output power is not provided. |
Application
u-Ring Topology and Application
Installation
The switch comes with both wall mount and DIN rail hardware brackets. When installing the DIN rail bracket, be sure to correctly align the orientation pin.
DIN Rail
Wall Mount
The switch with DIN Rail bracket has a steel spring in the upper rail of the bracket. This spring is compressed for mounting and un-mounting by applying downward force.
Mounting
Un-mounting
CTC Union Technologies Co., Ltd.
Far Eastern Vienna Technology Center
(Neihu Technology Park)
8F, No. 60 Zhouzi St., Neihu District, Taipei 114
Taiwan
T +886-2-26591021
F +886-2-26590237
E sales@ctcu.com
©2014 CTC Union Technologies Co., Ltd.
All trademarks are the property of their respective owners.
Technical information in this document is subject to change without notice.
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download CTC Union IGS-803SM-8PH24, IGS-803SM-8PHE24 Quick Installation Guide
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the IGS-803SM-8PH24 that isn't answered in the manual? Leave your question here.