Raymarine HSB Chartplotter User Manual
Raymarine HSB Chartplotter User Manual

Raymarine HSB Chartplotter User Manual

Raymarine hsb chartplotter radar: user guide
Table of Contents

Advertisement

Quick Links

Distributed by
Any reference to Raytheon or
RTN in this manual should be
interpreted as Raymarine.
The names Raytheon and RTN
are owned by the
Raytheon Company.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HSB Chartplotter and is the answer not in the manual?

Questions and answers

Summary of Contents for Raymarine HSB Chartplotter

  • Page 1 Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.
  • Page 2 HSB Series Chartplotter owner’s handbook Document number: 81150_1 Date: 18th September 1998...
  • Page 4: Safety Notices

    HSB Series Chartplotter Installation and Operation Handbook SAFETY NOTICES 1. HIGH VOLTAGE. The display unit contains high voltages. Adjustments require specialised service procedures and tools only available to qualified service technicians – there are no user serviceable parts or adjustments. The operator should never remove the display unit cover or attempt to service the equipment.
  • Page 5 RAYTHEON MARINE products are supported by a network of Authorized Service Representatives. For information on Raytheon products and services, contact either of the following: UNITED STATES Raytheon Marine Company 676 Island Pond Road Manchester, NH 03109-5420 Telephone: (603) 647-7530 Fax: (603) 634-4756 EUROPE Raytheon Marine Limited Anchorage Park...
  • Page 6: Emc Conformance

    Preface This handbook covers the chart aspects of the following HSB Series systems from Raytheon: System Chartplotter Raychart Combined Pathfinder Radar/Chartplotter Systems RL72RC RL74RC Repeater Displays Repeater Repeater Repeater It contains very important information on the installation and operation of your new equipment.
  • Page 7 HSB Series Chartplotter...
  • Page 8: Table Of Contents

    Contents Chapter 1: Overview... 1 1.1 Introduction ... 1 General ... 2 Display Unit Features ... 4 Display Unit Functions ... 4 Operating Modes ... 4 1.2 The Chartplotter Display ... 7 Chartplotter Display Options ... 8 1.3 Operating Controls ... 9 Trackpad and Cursor ...
  • Page 9 Place and Goto A Waypoint ... 34 Make and Follow a Route ... 36 Review Your Passage Plan ... 38 Displaying the Radar and Synchronising Radar & Chart ... 40 Chapter 3: Waypoints, Routes and Tracks ... 43 3.1 Introduction ... 43 Safety ...
  • Page 10 Placing a Waypoint ... 45 Selecting a Waypoint ... 46 Waypoint Data Display ... 47 Editing the Waypoint Details ... 47 Erasing a Waypoint ... 48 Moving a Waypoint ... 49 3.3Working with Routes ... 50 Creating a New Route ... 51 Saving the Current Route ...
  • Page 11 3.5 Transferring Waypoints and Routes ... 65 Displayed Seatalk Waypoints ... 65 Managing Database Lists ... 65 3.6 Using Tracks ... 67 Setting Up a Track ... 68 Clearing the Current Track ... 68 Managing Tracks ... 69 Saving and Naming a Track ... 69 Naming, Erasing and Showing a Track ...
  • Page 12 Help ... 86 Soft Keys... 86 Key Beep ... 86 MOB Data ... 86 Menu Timeout Period ... 86 Units ... 87 Variation Source ... 87 Auto Mode ... 87 Manual Mode ... 88 Cursor Echo ... 88 Date and Time Settings ... 88 Language ...
  • Page 13 Data Standards ...100 HSB ...100 SeaTalk ...101 NMEA ...102 SeaTalk and NMEA Data Received and Transmitted ...103 6.5 Cable Runs ...105 Power Cable ...105 6.6 Mounting the Display Unit ...106 Trunnion (Yoke) Mounting ...106 Console Mounting ...107 6.8 HSB Series System Connections ...108 Grounding the Chartplotter ...108 DC Power Connection ...108 Power for External Equipment ...108...
  • Page 14 7.2 Resetting the System ...118 7.3 Problem Solving...119 Common Problems and Their Solutions ...119 How to Contact Raytheon (US) ...119 For Marine Product and Services Information ...119 For Accessories and Parts ...119 For Technical Support: ...120 For Product Repair and Service ...120 How to Contact Raytheon Marine in Europe ...121 Technical Support ...121 Accessories and Parts ...121...
  • Page 15 HSB Series Chartplotter...
  • Page 16: Chapter 1: Overview

    Radar/Chartplotter RL70RC (refer to the Pathfinder HSB Series Radar Handbook, also provided with the combined system, for details on the radar functions). If you are using any HSB series 7" display unit as a chart repeater display you should refer to this handbook.
  • Page 17: Terminology

    Note: Installation of all HSB display units is the same, whether the unit is a chartplotter or a radar display. If you have both the HSB Series Pathfinder Radar or the HSB Series Chartplotter Handbook you can refer to either handbook for display unit installation details.
  • Page 18 HSB display (repeater display). In particular, you can connect your HSB Series Chartplotter to a remote HSB Series Radar to provide similar functionality to the combined Radar/Chartplotter. Full functionality of the HSB Series Chartplotter is achieved when it is part of an integrated system, with other equipment (in addition to another HSB unit) connected via Seatalk or NMEA 0183.
  • Page 19: Display Unit Features

    If you have a combined Radar/Chartplotter Unit, or have an HSB Radar connected three full-screen modes as shown opposite are available (chart, radar and data log); data log mode is used to initiate and display a running log of vessel travel. You select the mode using the DISPLAY key as described in Chapter two.
  • Page 20 Radar/Chartplotter) DISPLAY DISPLAY In addition, in chart or radar mode you can set Windows On to split the display into two half-screen windows for supplementary data display as described below. The upper window shows the selected mode (radar or chart); operating control defaults to the upper window, but you can switch control between the radar and chart window with a single key- press.
  • Page 21: Half-Screen Window Options

    (see Section 5.3 System Parameters). • Radar display: If radar data is available, either as a function of the combined display unit or via the HSB link, it can be displayed. Refer to the Pathfinder HSB Series Radar Handbook for detailed information.
  • Page 22: The Chartplotter Display

    Several functions are available to control the display as follows: • Zoom in/out and Pan the Display • Offset the Chart or Centre the Chart around the Vessel • Synchronise the Chart and Radar (if radar data is available) Operation of these functions is described in Chapter 2.
  • Page 23: Chartplotter Display Options

    Chartplotter Display Options Set up options allow you to customise the chart by choosing what is, or is not displayed, how it is displayed (including language and units), heading mode and how the chartplotter operates with other HSB units. You can also view the cursor position and a variety of data from other equipment, e.g.
  • Page 24: Operating Controls

    Chapter 1: Introduction 1.3 Operating Controls You operate the chartplotter in a variety of ways; the control keys on the display unit are used with on-screen facilities such as pop-up menus. These include: • A trackpad providing up, down, left, right and diagonal control of an on-screen cursor.
  • Page 25: Trackpad And Cursor

    Text Label HSB Series Chartplotter Feature Ruler line Data box (any type) Course Over Ground vector Heading vector Radar Mark Man Over Board marker...
  • Page 26: Dedicated Keys

    These keys have fixed functions; the functions are similar on all HSB Series displays. For example, ALARMS is used to set up the system alarms on both a chartplotter and a radar. Some keys can be used in two ways: •...
  • Page 27: Soft Keys

    Soft Keys The four keys below the screen are called soft keys because their functions change according to the operation. The soft keys are grouped into related sets and subsets providing access to the various functions. The soft key labels are displayed on the screen just above the keys. The default soft keys are displayed until you press a key, or select an item on the screen;...
  • Page 28: Chapter 2: Getting Started & Adjusting The Display

    Chapters 3 and 4. When you become familiar with the system you can choose the method that suits you best. If you have a combined Radar/Chartplotter, refer to the HSB Series Radar Handbook for information on power-up and on using the radar functions.
  • Page 29: Switching The Display Unit On And Off

    2.2 Switching the Display Unit On and Off This section explains how to switch the chartplotter display on and off. The following description assumes that there is no radar scanner connected to the chartplotter. To turn the chartplotter display on, press and hold the POWER key until the unit beeps.
  • Page 30: Changing The Lighting And Contrast

    Chapter 2: Getting Started Changing the Lighting and Contrast You can change the level of backlighting and contrast for the screen and the keys. The key lighting is set the same as the display lighting, except that it remains switched on at its lowest level even when the screen lighting is turned off, so that you can always find the keys.
  • Page 31: Chart Simulator

    ON. If you have a combined Pathfinder radar/chartplotter display, or you are using your chartplotter as a radar repeater you can also switch on the radar simulator To view a chart (and radar) image using simulated data: 1.
  • Page 32: Using Chart Cards

    Chapter 2: Getting Started 2.3 Using Chart Cards The chartplotter has a built-in world map that can be used for route planning. Most areas are covered on a scale of about 500nm per inch on the screen (200nm per cm), although some populated areas have details down to 300nm on the screen.
  • Page 33: Displaying The Chart Data

    5. Close the card cover so that is clicks shut, to prevent water entering the display unit. Displaying the Chart Data The new chart information will be displayed when you move the cursor into an area covered by the new chart or, if it is already in the area, change the range scale.
  • Page 34: Displaying Chart Information

    Chapter 2: Getting Started Displaying Chart Information Chart cards include a number of displayed objects for which information is available, such as lights and buoys. Chart source data is also available and, if your chart includes port and tide data, this can be displayed.
  • Page 35: Controlling The Display

    • Move around the chart by panning the display, changing the chart centre and changing the chart scale. Synchronising the chart and radar images is also described here. • Customise the screen presentation options. The chart controls are summarised in the illustration on the fold- out page at the end of this section.
  • Page 36 3. When you press DISPLAY again, the pop-up and soft keys for the current full-screen mode are shown.The selected mode is shown full-screen. However, in Chart and Radar mode you can switch on half-screen windows for additional display, as described in the following section.
  • Page 37: Selecting A Half-Screen Window For Display

    Switching Control Between Radar & Chart Screens In a combined or integrated system, to switch control between radar and chart, you can change the full-screen mode. Alternatively, when you...
  • Page 38 Chapter 2: Getting Started CDI Window WINDOWS SELECT OFF ON WINDOW Navdata Window WINDOWS SELECT OFF ON WINDOW BDI Window WINDOWS SELECT OFF ON WINDOW Radar Window WINDOWS SELECT OFF ON WINDOW D4271-1...
  • Page 39: Returning To The Full-Screen Display

    Alternatively, you can home the cursor onto the vessel using FIND SHIP; this function can also be used on a combined display to sychronise the radar and chart windows as described in Using FIND SHIP . There are four ways in which you can move the chart: •...
  • Page 40: Using Find Ship

    • In full-screen chart mode FIND SHIP is used to re-draw the chart with the vessel at the centre and the cursor homed onto the vessel. • On a combined radar/chartplotter display, with chart and radar half- screen windows FIND SHIP can also be used to synchronise the radar and chart images.
  • Page 41: Changing The Chart Scale

    If you have a combined radar/chartplotter display, with chart and radar windows on, and you have selected Radar/Chart Synch in Chart Set Up ( see Chapter 5 ). FIND SHIP also synchronises the radar and chart images as follows: • The chart is redrawn so that its centre position matches that of the radar display.
  • Page 42 Chapter 2: Getting Started • To move the display to another area of the chart, by zooming out to a small scale chart, then zooming in on another position Each time you press the RANGE key, the chart scale changes to the next available setting.
  • Page 43 Chart Boundary - indicates further detail is available inside 4. When no further chart detail is available, as you press the bottom of the RANGE key, the effect depends on whether Plotter Mode is on or off as follows: • If Plotter Mode is Off, the unit beeps three times and the chart scale remains unchanged, indicating the smallest chart scale is displayed.
  • Page 44: Customising The Screen Presentation Options

    Chapter 2: Getting Started Customising the Screen Presentation Options The SCREEN soft key lets you set the following screen presentation options on or off: CRSR BOX CHRT GRID OFF ON Cursor Data Box On and Off The cursor data box provides the cursor’s position. If you wish to see a full chart, you can switch the data box off.
  • Page 45: Custom Options

    The default data box positions are along the bottom of the chart. Each box can be moved to the required position on the screen using the context-sensitive cursor. At any time, you can switch the group of data boxes on or off using the SCREEN soft key.
  • Page 46 Chapter 2: Getting Started...
  • Page 47 HSB Series Chartplotter...
  • Page 48: Typical Scenarios

    • Review the Passage Plan View Route Information Change the SOG, Hours and ETA. • Displaying the Radar Image and Synchronising Radar & Chart Changing the Full-Screen Mode & Selecting Half-Screen Windows Radar and Chart Synchronisation (Find Ship) Cursor Echo...
  • Page 49: Place And Goto A Waypoint

    Place and Goto A Waypoint HSB Series Chartplotter 1. Press MARKS 2. Position Cursor as required Press the soft key Press the soft key to go to the waypoint selected by the cursor. D4267-1...
  • Page 50 Chapter 2: Getting Started The vessel navigates towards the target waypoint See: 3.2 Working wth Waypoints Go to an individual Target Point, page 63. D4267-1a...
  • Page 51: Make And Follow A Route

    Make and Follow a Route ROUTE GOTO MAKE EDIT ROUTE ROUTE SCREEN FIND SHIP Press the soft key CLEAR ROUTE MORE! Press the soft key 1. Position Cursor - in this example over an existing waypoint 2. Press the soft key Position Cursor for next waypoint, then press soft key.
  • Page 52 Chapter 2: Getting Started ROUTE GOTO GOTO GOTO CURSOR WAYPOINT STOP GOTO FOLLOW CURSOR Press the soft key. The route becomes the current route. SCREEN FIND SHIP Press the soft key FOLLOW ROUTE Press the soft key The vessel starts to navigate to the first (target) waypoint in the route.
  • Page 53: Review Your Passage Plan

    Review Your Passage Plan ROUTE GOTO MAKE EDIT ROUTE ROUTE REVERSE SAVE ROUTE ROUTE SCREEN FIND SHIP Press the soft key CLEAR ROUTE MORE! Press the soft key ROUTE LIST MORE! Press the soft key 1. Use the trackpad to move selection bar over required route.
  • Page 54 Chapter 2: Getting Started See: Displaying Route Information page 55. Change the TIME to HOURS - the display indicates it will take 32 minutes to reach the destination. You can change the PLANNED SOG; the display updates to indicate TIME required at the planned speed.
  • Page 55: Displaying The Radar And Synchronising Radar & Chart

    Displaying the Radar and Synchronising Radar & Chart ROUTE GOTO SYSTEM CHART SET UP! SET UP! 1. Press DISPLAY -- then press twice more to select RADAR. 2. Press the soft keys to set windows ON. The Chart window is the default selection.
  • Page 56 Move the chart cursor - - you can see chart cursor move on the radar screen. You can move the cursor over a radar target to determine its identity on the chart See: 2.4 Controlling the Chart Display 4.5 Cursor Echo 5.3 System Parameters...
  • Page 57 HSB Series Chartplotter...
  • Page 58 Soft Key Labels: Change when you press a key. Default soft key labels are shown. ROUTE GOTO SCREEN FIND SHIP Soft keys Press to select option, or highlight option or slider. Labels change when you press soft/dedicated key. Elipses (...) after the text indicate that pressing soft key leads to further options.
  • Page 59 ROUTE MAKE PLACE UNDO ACCEPT ROUTE WAYPOINT WAYPOINT ROUTE Use the soft keys to set up a series of waypoints as a route. Use the trackpad to move the cursor then press PLACE WAYPOINT, continue until the route is complete. Press ACCEPT ROUTE to finish.
  • Page 60: Chapter 3: Waypoints, Routes And Tracks

    Chapter 3: Waypoints, Routes and Tracks Chapter 3: Waypoints, Routes and Tracks 3.1 Introduction This chapter explains how to use the chart functions to navigate with your HSB Series display. It covers the following topics: • Controlling waypoints, including placing, moving, editing and deleting waypoints.
  • Page 61: Working With Waypoints

    You can place waypoints before you install the chartplotter on your vessel. Note: Radar marks may also be displayed on the screen if your chartplotter is a combined radar/chartplotter or is part of an integrated system;...
  • Page 62: Placing A Waypoint

    Chapter 3: Waypoints, Routes and Tracks To access waypoint soft keys, press MARKS: PLACE WPT PLACE WPT AT CURSOR AT VESSEL Placing a Waypoint The Place and Goto a Waypoint Scenario in Chapter 2 provides a simple example of how to place a waypoint. To place a waypoint at the cursor position or at the vessel position: 1.
  • Page 63: Selecting A Waypoint

    2. Press the MAKE NEW WAYPOINT softkey. MAKE NEW WAYPOINT The waypoint is placed at the current vessel position, or if not available, the cursor position. It is added to the Waypoint List and named with the next available number. To return to the default softkey display, press ENTER twice.
  • Page 64: Waypoint Data Display

    Chapter 3: Waypoints, Routes and Tracks Waypoint Data Display Waypoint data can be viewed in two ways: you can use the context- sensitive cursor to select the waypoint and thus display the waypoint data box, or you can view waypoint details on the waypoint list. Note: To permanently display the target waypoint data box, select it in the System Set Up menu (see Chapter 5) and use the SCREEN soft key to switch data boxes on.
  • Page 65: Erasing A Waypoint

    3. To edit the symbol, press the SYMBOL soft key. Use the soft keys, shown in the following illustration, to highlight the required symbol , then press ENTER. 4. To edit the waypoint name, press the NAME soft key. The NAME WAYPOINT window is displayed. Use the trackpad to enter or edit the name: Use the left or right side of the trackpad to move the cursor to the character you wish to change.
  • Page 66: Moving A Waypoint

    Chapter 3: Waypoints, Routes and Tracks To delete a waypoint using the cursor: 1. Move the cursor over the waypoint, until the letters WPT are displayed. The waypoint soft keys are displayed. ERASE WAYPOINT 2. Press the ERASE WAYPOINT soft key. The waypoint is removed from the screen and the Waypoint List is updated.
  • Page 67: Working With Routes

    3.3 Working with Routes A route is made up of a series of waypoints (maximum 50). To make a route you place a series of waypoints on the chart. When a route is created it becomes the current route and is displayed on-screen.
  • Page 68: Creating A New Route

    Chapter 3: Waypoints, Routes and Tracks • Creating a new route. • Saving the current route in the database list. • Clearing the current route. • Retrieving a route from the database list as the current route. • Displaying route information, including the route leg data and waypoint details.
  • Page 69 3. Move the cursor to the position on the chart where you want your first PLACE WAYPOINT waypoint to be. Press the PLACE WAYPOINT softkey. Note: You can position the cursor on an existing waypoint, if required – the text WPT indicates you are re-using the waypoint rather than placing a new one.
  • Page 70: Saving The Current Route

    Chapter 3: Waypoints, Routes and Tracks Saving the Current Route You can save up to 20 named routes in the route database list. These routes can then be re-displayed and followed at a later date. Note: If the current route has not been saved, when you attempt an operation that affects this route, e.g.
  • Page 71: Clearing The Current Route

    If you wish to name the route press the YES soft key. Use the trackpad to move the cursor right or left to the character you wish to edit. Then use the top or bottom of the trackpad to increase or decrease the letter or number.
  • Page 72: Displaying Route Information

    Chapter 3: Waypoints, Routes and Tracks SHOW ROUTE 2. Use the trackpad to select the required route then press the SHOW SHOW ROUTE soft key. The route list is removed and the selected route is shown on screen as the current route. Displaying Route Information You can display the following information that relates to your route: •...
  • Page 73: Using Route Information To Review Your Passage Plan

    Using Route Information to Review Your Passage Plan You can view data for all the waypoints in the current route, or any saved route. You select the route from the database list and the information is displayed in a Route Information pop-up; the following details are provided for each waypoint: Position Bearing (from previous waypoint)
  • Page 74: Using The Route List To Erase And Name A Route

    Chapter 3: Waypoints, Routes and Tracks INFO FOR ROUTE-CURRENT ROUTE WPT POSITION BRG DISTANCE TOTAL TIME 50°21^97N --- 001°15^80W 50°21^97N 090 001°08^75W 50°27^48N 000 001°08^75W TIME ETA TOTAL 4. Press ENTER or CLEAR to clear the Route Information window, then ENTER or CLEAR to return to the route soft keys. To return to the default soft key display, press ENTER .
  • Page 75: Editing A Route

    3. If you NAME a route, use the trackpad to move the cursor right or left NAME ROUTE to the character you wish to edit. Then use the top or bottom of the trackpad to increase or decrease the letter or number. 4.
  • Page 76: Adding Waypoints At The End Of The Route

    Chapter 3: Waypoints, Routes and Tracks Adding Waypoints at the End of the Route To add waypoints at the end of the route: 1. Press the ROUTE soft key, followed by the EDIT ROUTE soft key. EDIT ROUTE The Make Route soft keys are displayed and the cursor is connected to the last-placed waypoint with a dotted line.
  • Page 77: Following Routes And Going To Points

    3.4 Following Routes and Going to Points The default soft key GOTO accesses the functions to FOLLOW a route and GOTO a waypoint or cursor. When you select the target destination, the chartplotter calculates bearing, distance and cross track error; this information is passed to a helmsman or autopilot.
  • Page 78: Follow A Route

    Chapter 3: Waypoints, Routes and Tracks Follow a Route Note: The current route may have been created on this display, or created on another unit and received on this display via SeaTalk. To follow the current route: 1. Press the GOTO default soft key. The Goto/Follow soft keys are GOTO displayed.
  • Page 79: Target Point Arrival

    Target Point Arrival You can set up target alarms (see Chapter 4) to alert you when the vessel is approaching the target point. The arrival alarm is defined as a circle (not visible on the screen), with a specified radius around the target.
  • Page 80: Advancing To A Waypoint

    Chapter 3: Waypoints, Routes and Tracks Advancing to a Waypoint Once you are following a route, you can advance to the next waypoint, even if you have not reached the current target waypoint: 1. If necessary, press the GOTO default soft key to display the Goto/ GOTO Follow soft keys.
  • Page 81: Stop Follow Or Stop Goto

    2. Press the GOTO WAYPOINT soft key. GOTO WAYPOINT Navigation to the selected waypoint begins. The soft key STOP GOTO is displayed. 3. To return to the default soft key display, move the cursor away from the waypoint. To navigate directly to the cursor position: 1.
  • Page 82: Displayed Seatalk Waypoints

    Chapter 3: Waypoints, Routes and Tracks 3.5 Transferring Waypoints and Routes Displayed Seatalk Waypoints In an integrated system, when a route is made current on any Seatalk equipment it is sent to all SeaTalk instruments, including this chartplotter; this route will override any other current route. When GOTO waypoint or GOTO cursor is in operation it is considered a route The current route can be edited on any instrument with route edit capability.
  • Page 83 2. Press the soft key RECEIVE WPTS FROM ST/NMEA. RECEIVE WPTS FROM When waypoints are transmitted by other equipment they are added ST/NMEA to the open waypoint list on the chartplotter. Routes transmitted on NMEA are appended to the route list. 3.
  • Page 84: Using Tracks

    Chapter 3: Waypoints, Routes and Tracks 3.6 Using Tracks The Track function is used to mark on-screen the trail that your vessel has followed, as if it had left a visible fixed wake. While the track is turned on, it is recorded in the display unit’s memory. You specify the interval at which track points are made, a line is drawn on-screen between each point.
  • Page 85: Setting Up A Track

    Setting Up a Track You use the track soft keys to switch the track on and to specify the interval at which track points are saved. The interval default is a distance of 0.1nm. The maximum track length is 1000 points, when the track has reached this length, the first points are overwritten.
  • Page 86: Managing Tracks

    Chapter 3: Waypoints, Routes and Tracks Managing Tracks Although it is easy to set up a track, and this track is retained even if you turn off your display, you can store a number of different tracks so that you can review them at a later date. This section explains how to perform the following tasks: •...
  • Page 87: Naming, Erasing And Showing A Track

    Naming, Erasing and Showing a Track To name an existing track, erase a track or show a track, you select the track from the track list, then press the appropriate soft key as follows: 1. Press the TRACK LIST soft key. The Track List is displayed. The TRACK LIST grey selection bar indicates the selected track.
  • Page 88: Chapter 4: Further Chart Operations

    Chapter 4: Further Chart Operations 4.1 Introduction This chapter explains how to use the additional functions that are provided on the HSB series chartplotter and combined radar/ chartplotter. It covers the following topics: • Measuring distances and bearings on the chart, using the VRM/EBL •...
  • Page 89: Measuring Distances Using The Vrm/Ebl Key

    4.2 Measuring Distances Using the VRM/EBL Key You can obtain an accurate measurement of the distance and bearing between two points by using the VRM/EBL key. To place a ruler line and Ruler data box: 1. Position the cursor on the starting point from which you wish to measure.
  • Page 90 Chapter 4: Further Chart Operations 4. Press ENTER to fix the end point of the ruler line, and return to normal cursor control. The letter “B” marks the location of the end point on the chart. To re-position one end of the ruler line: 1.
  • Page 91: Alarms And Timers

    4.3 Alarms and Timers Alarm Reporting The chartplotter reports the following alarms, that are set using the ALARMS key: Alarm Arrival Off Track Anchor Countdown Alarm Clock The alarms are switched on or off, and the limits set, using the ALARMS key menu.
  • Page 92: Setting Alarms And Timers

    Chapter 4: Further Chart Operations Setting Alarms and Timers To set up an alarm or timer: 1. Press the ALARMS key. The Alarms Set Up list is displayed, showing the current settings. ARRIVAL ALARM OFF TRACK ALARM ANCHOR ALARM COUNTDOWN TIMER ALARM CLOCK 2.
  • Page 93: Man Overboard (Mob)

    4.4 Man Overboard (MOB) If you lose a person or object overboard, and need to return to the location, you should use the Man Overboard (MOB) function. You can select the type of data used for the MOB position using the set up menus (see Chapter 5).
  • Page 94: Cursor Echo

    Seatalk, you can set the display to enable cursor echo. Cursor echo (accessed from System Set Up, described in Chapter 5) enables you to display a radar cursor on the chart picture, or a chart cursor on the radar picture (you cannot display a remote chart cursor in a chart window).
  • Page 95 RESTART To tune a differential GPS to another beacon: 1. Press D-GPS SETUP, the Differential GPS Setup pop-up is D-GPS SETUP! displayed with MODE and BEACON SELECT soft keys. 2. Press MODE AUTO MAN to toggle the GPS to manual tuning. 3.
  • Page 96: Data Log Mode

    Chapter 4: Further Chart Operations 4.7 Data Log Mode You can set the chartplotter to log course data every thirty minutes. Up to 48 log entries are held, when 48 entries have been made, the chartplotter will start overwriting the first entries. You start the log using soft keys provided in Data Log Mode.
  • Page 97 TIME POSITION 15:30 50°21^890N 001°20^610W 16:00 50°18^010N 001°20^070W 16:30 50°21^850N 001°19^290W 17:00 50°18^500N 001°21^300W 17:30 50°20^990N 001°18^280W 18:00 50°19^660N 001°21^960W 18:30 50°19^730N 001°18^030W 19:00 50°20^930N 001°21^750W 19:30 50°18^550N 001°18^650W STOP LOG To stop recording log entries: Press the STOP LOG soft key. STOP LOG To clear the log entries: Press the CLEAR LOG soft key, you are prompted “Are You Sure”.
  • Page 98: Chapter 5: Setting Up The Chartplotter

    Note: If you have a combined Radar/Chartplotter display, the SYSTEM SET UP menu from the chart display is the same as that accessed from the radar display. An additional set up menu is available for the radar functions when you are in Radar mode. Refer to the HSB Series...
  • Page 99: Changing The Set Up Parameters

    • System, controlling the aspects of the system that are not specific to the chartplotter • Chart, controlling the chartplotter, including waypoint information, vectors and radar/chart synchronisation. This section provides instructions for displaying and changing the default values. The following sections list the parameters and their possible settings, and describe the function of each parameter in turn.
  • Page 100: System Parameters

    Chapter 5: Setting Up the Chartplotter 6. Press ENTER, MENU or CLEAR to clear the soft keys and return to the normal display. You can return all the settings to their original factory settings, if required, by performing a factory reset as described in Chapter 7. 5.3 System Parameters The following table lists the System menus and their options, shows the factory default setting, and provides a space for you to make a note of...
  • Page 101 12 HOUR 24 HOUR 24 HOUR UTC, or local offset value: Plus or minus up to 12 hours, in whole hours ENGLISH (UK), ENGLISH (UK) ENGLISH (US), DANISH, FRENCH, GERMAN, DUTCH, ITALIAN, NORWEGIAN, PORTUGESE, SPANISH, SWEDISH, FINNISH DATA RADAR BOTH Default...
  • Page 102: Data Boxes

    Chapter 5: Setting Up the Chartplotter Data Boxes Press the SELECT BOXES soft key to display the data box sub-menu. This allows you to select up to 6 data boxes that you wish to be able to display on the chart screeen. Note: A fixed set of 9 of these data items are available for display in the Nav Data window.
  • Page 103: Day/Night

    Day/Night This option allows you to change the chart presentation between “day” and “night” modes. In the normal day presentation, black objects are displayed on a white background. If you select NIGHT presentation, the picture is reversed, so that white objects are shown on a black background to reduce the intensity of the image.
  • Page 104: Units

    Chapter 5: Setting Up the Chartplotter This setting does not affect the default soft key labels, which are controlled by the Soft Keys option previously described. Units You can set the units for distance, speed, depth and temperature. The units you set will be used to display all data, including information received from other instruments on the system.
  • Page 105: Manual Mode

    • Remote Cursor (SeaTalk): displays the cursor from another radar or chartplotter connected via SeaTalk Cursor echo functions so that you can display a radar cursor on the chart picture, or a chart cursor on the radar picture (you cannot display a remote chart cursor in a chart window).
  • Page 106: Language

    • Both on a combined radar/chartplotter, provides simulated data and radar picture. Note: On a radar master display, you cannot view a simulated image whilst the scanner is in transmit mode. If you switch the simulator on during transmit mode, the scanner is set to standby, and you will be unable to re-select transmit mode until the simulator is switched off.
  • Page 107: Chart Set Up Parameters

    PLOTTER MODE CHART ORIENTATION NORTH UP OBJECT INFORMATION OFF WAYPOINT WAYPOINT NUMBERS OFF DEFAULT WAYPOINT SYMBOL HEADING VECTOR COG VECTOR TIDE VECTOR RADAR/CHART SYNCH DATUM SELECTION HSB Series Chartplotter Options Factory Default See below for details NORTH UP COURSE UP...
  • Page 108: Customise Chart

    Chapter 5: Setting Up the Chartplotter Customise Chart This provides a list of chart options, enabling you to specify how the chart features are displayed. Most options can be toggled between on, off and custom - custom passes on/off control to the SCREEN soft keys (see Customising the Screen Presentation Options in Chapter 2 ).
  • Page 109: Object Information

    Object Information You can set Object Information ON or OFF. When set ON, object information is displayed in normal chartplotter operation when the cursor is placed over a chart object for two seconds. When set OFF, no information is displayed. Waypoint Options Waypoint controls whether or not the waypoints are shown on the Chart display, with their appropriate symbols.
  • Page 110: Chapter 6: Installation

    Handbook . Compass Note: If you wish to practice using the radar display before installation, you can set it up by connecting a 12V or 24V DC power supply (connecting the red core from the power lead via a 6.3A quick blow fuse to positive and the black core to negative) and using the simulator mode, as described in Chapter 2 Getting Started .
  • Page 111: Emc Installation Guidelines

    VHF radios, cables and antennas. In the case of SSB radios, the distance should be increased to 2m (7ft). • More than 2m (7ft) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element.
  • Page 112: Planning The Installation

    Chapter 6: Installation If your Raytheon equipment is going to be connected to other equipment using a cable not supplied by Raytheon, a suppression ferrite MUST always be fitted to the cable close to the Raytheon unit. Planning the Installation Before you install your system, you should spend some time planning the installation, giving consideration to: •...
  • Page 113: Unpacking And Inspecting The Components

    7” LCD Display 7” LCD Display Accessories Sun cover (light grey) Sun cover (White) Handbook, Radar Handbook, Chart Quick Reference Card, Radar Quick Reference Card, Chart Mounting bracket assy. Trunnion knobs (x2) Flush mount kit Power cable Seatalk cable assembly...
  • Page 114: Location

    Chapter 6: Installation 6.3 Location This section provides information that affects the possible locations of the display unit, and its position relative to the power supply. Selecting the Display Unit Site The display unit can be mounted using the trunnion (yoke) bracket already fitted, or console mounted using the optional flush-mounting kit.
  • Page 115 When planning the installation of your display unit, the following points should be considered to ensure reliable and trouble free operation: • Convenience: The display unit should be installed in a convenient position, where it can be viewed straight on or with a viewing angle of less than 35°.
  • Page 116: Integrated Systems

    The HSB series displays can be linked via the HSB network to transfer chart and radar data between units; this enables a second, repeater display to be used to view and control the chart or radar. The display unit can also receive external signals to drive various features, such as the North Up mode and waypoint display.
  • Page 117: Data Standards

    Likewise, radar timed transmission is not available on a repeater display). For example, you could connect an HSB Radar display and an HSB Chartplotter display, to enable you to display and control both radar and chart data on either or both displays. The HSB series displays allow you to select either type of data for display, or display both types at the same time, in half-screen windows.
  • Page 118: Seatalk

    Chapter 6: Installation SeaTalk The SeaTalk standard was originally developed by Autohelm (part of the Raytheon group), and allows compatible instruments to be connected by a single cable carrying power and data in/out. This means that additional instruments and functions can be added to a SeaTalk system, simply by plugging them into the network.
  • Page 119: Nmea

    NMEA The NMEA 0183 Data Interface Standard was developed by the National Marine Electronics Association of America. It is an international standard that enables equipment from many different manufacturers to be connected together and to share information. The information is passed in “sentences”, each of which has a three- letter sentence identifier.
  • Page 120: Seatalk And Nmea Data Received And Transmitted

    For this reason NMEA 0183 is generally used to connect a data receiver and a transmitter together: for example, a compass sensor transmitting heading to a radar, or a GPS sensor (or Chart Plotter) transmitting position and navigation data to a radar.
  • Page 121 Total Log and Trip Log Water Temperature Heading Magnetic Variation Time Date MOB data Cursor Position EBL/VRM Positions Heading mode Radar display range HSB Series Chartplotter SeaTalk NMEA GGA GLL RMC RMC VTG APB BWC RMB APB BWC RMB BWC RMB APC RMB —...
  • Page 122: Cable Runs

    10.7 to 32VDC range (that is, 12V and 24V systems, not 32V systems). A 1.5m (5ft) power cable is supplied for connecting the ship’s DC power to the radar. If a longer power cable run is required, use the supplied power cable to connect to the display unit.
  • Page 123: Mounting The Display Unit

    power source and the connector block, and then select the wire size indicated by the distance following table. Maximum Extension Power Cable Lengths (m), 12V Systems Inter-Unit Cable(s) Maximum extension 6.6 Mounting the Display Unit The display unit can be mounted using the trunnion (yoke) bracket already fitted, or console mounted using the optional flush-mounting kit (see section 6.2).
  • Page 124: Console Mounting

    Chapter 6: Installation Console Mounting The display unit can be console mounted if required, using the optional flush-mounting kit (M92708). CAUTION: Make sure there are no hidden electrical wires or other items behind the location before proceeding. Make sure there is sufficient rear access for mounting and cabling.
  • Page 125: Hsb Series System Connections

    6.8 HSB Series System Connections Grounding the Chartplotter It is important that an effective RF ground is connected to the chartplotter. You must ground the system by connecting the drain wire (screen) of the Power/NMEA Input cable to the nearest ground point of the ship’s RF ground system.
  • Page 126: Display Unit Connections

    The rear of the HSB Series display provides the following connection sockets: • HSB, for connecting to another HSB Series display (such as a radar or second chartplotter display) • SeaTalk, for SeaTalk data input and output and connecting to another HSB Series display (such as a radar or second chartplotter display) •...
  • Page 127: Hsb Connection

    HSB Connection You can connect any two HSB displays, using an HSB cable connected between their HSB connectors on the rear of each display unit. Note: The HSB cables are fitted with ferrite clamps at each end to ensure EMC conformance. SeaTalk Connection The SeaTalk input/output should be connected at the rear SeaTalk 3-pin connector.
  • Page 128: Nmea Output To External Navaids

    Chapter 6: Installation To connect the display unit to the SeaTalk bus, connect a standard SeaTalk cable between the SeaTalk connector on the rear of the display and a SeaTalk instrument or the SeaTalk bus. Standard SeaTalk cables are available in a range of lengths (part numbers W284 to W287), and cables for connecting to older SeaTalk units are also available (part numbers D187 or D188).
  • Page 129 Connect the input(s) to the orange and yellow cores (Channel 1) and/or the green and blue cores (Channel 2). Note: Navaids cannot be powered from the radar. For example, to connect a Raytheon Heading Sensor to the NMEA Channel 1 input, connect the cables and power supply using a suitable connector block, as shown in the diagram below.
  • Page 130: Using The Seatalk Auxiliary Junction Box To Connect A Seatalk Gps

    Chapter 6: Installation Using the SeaTalk Auxiliary Junction Box to Connect a SeaTalk GPS A junction box (provided with the RL70RC, optional with the RL70) is used to connect the SeaTalk GPS system (or any other SeaTalk instrument) to the HSB Series display unit. This junction box enables the SeaTalk bus, power and GPS to be connected.
  • Page 131: System Check And Initial Switch On

    To switch on the display unit, press and hold the POWER key until the unit beeps. If the display switches on in Radar (following a magnetron warm-up sequence) or Data Log mode, press DISPLAY to show the Display pop- up. Press DISPLAY again, as necessary, to select Chart mode, then press ENTER.
  • Page 132: Checking The Chartplotter Operation

    Chapter 6: Installation SYSTEM SET UP MENU DATA BOXES BEARING MODE CURSOR REFERENCE CURSOR READOUT DAY/NIGHT HELP SOFT KEYS KEY BEEP MOB DATA MENU TIMEOUT PERIOD DISTANCE UNITS SPEED UNITS DEPTH UNITS TEMPERATURE UNITS VARIATION SOURCE CURSOR ECHO DATE FORMAT TIME FORMAT TIME OFFSET LANGUAGE...
  • Page 133 HSB Series Chartplotter...
  • Page 134: Chapter 7: Maintenance And Problem Solving

    The operator should not remove the rear cover of the `display or any internal covers in the scanner. Always turn the radar system off before carrying out any routine maintenance on the scanner or nearby equipment. Routine Checks The Chartplotter display ia a sealed unit.
  • Page 135: Resetting The System

    7.2 Resetting the System There are three types of reset available for the HSB Series Chartplotter: • Factory Reset: This resets all values back to their original factory settings. CAUTION: The factory reset clears the Waypoint and Route databases. • Power-On Reset: When you turn the display off and on again, the screen reverts to the chart picture with all windows cleared.
  • Page 136: Problem Solving

    For Marine Product and Services Information Visit the Raytheon World Wide Web site for the latest information on the newest Raytheon Marine electronic equipment and systems at: www.raymarine.com For Accessories and Parts Many Raytheon accessory items and parts can be obtained directly from your authorized Raytheon dealer.
  • Page 137: For Technical Support

    Raytheon products. Questions may be addressed directly to our Technical Support Department via the Internet at: rmc_tech_raytheon@raymarine.com . For Product Repair and Service In the unlikely event your Raytheon unit should develop a problem, please contact your authorized Raytheon dealer for assistance.
  • Page 138: How To Contact Raytheon Marine In Europe

    Our technical support staff may also be reached via the Internet. Questions may be addressed directly to: techsupra@raytheon.com . Or visit the Raytheon Electronics World Wide Web site: www.raymarine.com Technical Support The Customer Services Department handles enquiries concerning installation, operation, fault diagnosis and repair.
  • Page 139 HSB Series Chartplotter...
  • Page 140: Appendix A: Specification

    Appendix A: Specification HSB Series 7” LCD Displays General Approvals CE - conforms to FCC - conforms to Size Weight Mounting Power Environmental Controls Cursor Display Type Resolution Display Size LCD Contrast Illumination Languages Connectors Interfaces Man Overboard (MOB Mode) 89/336/EEC (EMC).
  • Page 141: Chartplotter Features

    Bearing and distance to cursor, Seatalk data (see ‘interfacing’ section) Auto (SeaTalk/NMEA/Internal algorithm) or Manual User selectable in split screen mode provided radar data available Fully independant use of remote Chart data if present on HSB. Full remote control and display of Radar data if present on HSB Depth, Speed Over Ground &...
  • Page 142: Abbreviations

    Abbreviations ANSI GPS, dGPS GHz, IEEE in, " American National Standards Institute American Wire Gauge Bearing Deviation Indicator Bearing Course Deviation Indicator Code of Federal Regulations Course Over Ground Centre deciBels Direct Current Dead Reckoning Electronic Bearing Line Electro Magnetic Compatability Federal Communication Commission Float - floating EBL/VRM feet...
  • Page 143 kilogram kilo Watt latitude pounds Liquid Crystal Display longitude Magnetic metres Main Bang Suppression millimetre Man OverBoard Mark nauticl mile NMEA National Marine Electronics Association Position (of vessel) Radio Frequency Range Revolutions Per Minute Ships Heading Marker Speed Over Ground True Time To Go Volts...
  • Page 144: Operating Modes

    Route 54 Track 68 Data Box 83 COG Vector 90, 92 Combined Display Definition 2 Combined Radar/Chartplotter 3, 77 Operating Modes 4 Connections 108 Display Unit 109 HSB 99, 110 NMEA Out 99, 111, 112 Power & NMEA In 99, 108, 112...
  • Page 145 Create a Route 51 Cross Track Error. See XTE: Data Box Current Route 50 Clear 54 Save 53 Cursor 9, 10 Context-sensitive 10 Data Box On/Off 29 Goto 60 Cursor Echo 77, 84, 88 Local 77 Remote 77 Cursor Readout 83, 85 Cursor Reference 83, 85 Custom Options 30 Customise Chart 90, 91...
  • Page 146 HSB 99 Connection 108, 110 Data 100 Definition 2 HSB Connection 3 HSB Series Display Unit. See Display Unit Identifying a Radar Target on the Chart Display Sc 40 Inserting a Waypoint in a Route 58 Chart Card 17 Installation 93–115...
  • Page 147 Power-on Sequence 14 Problem Solving 119 Radar Display Definition 2 Mode 4, 20 Options 6 Radar/Chart Synchronisation 25, 26, 90 RANGE key 26, 27 Remote Cursor Echo 77, 88 Removing a Waypoint from a Route 59 Chart Card 19 Repeater...
  • Page 148: Review Your Passage Plan

    Safety i, 43 Save Route 53 Track 69 Scenarios 33 Identify a Radar Target on the Chart Display 40 Make & Follow a Route 36 Place & Goto a Waypoint 34 Review Your Passage Plan 38 Screen Presentation Options 29...
  • Page 149 Editing Details 47 Wind Data Box 83 Window Options 5, 6–7 BDI 6, 23 CDI 6, 23 Nav Data 6, 23 Radar 6, 23 Windows Half Screen 5 World Map 7, 17 World Wide Support 121 Data Box 83 Restart 60, 63...
  • Page 150: Limited Warranty Certificate

    Company or authorized service agent at the time of request for Warranty service. Consumable items, (such as: Chart paper, lamps, fuses, batteries, styli, stylus/drive belts, radar mixer crystals/ diodes, snap-in impeller carriers, impellers, impeller bearings, and impeller shaft) are specifically excluded from this Warranty.
  • Page 151: Factory Service Center

    United States of America Raytheon Marine Company 676 Island Pond Road Manchester, NH 03109-5420 U.S.A. UK, Europe, Middle East, Far East Raytheon Marine Company Anchorage Park, Portsmouth PO3 5TD, England Purchased from Dealer Address Installed by Commissioned by Owner’s name Mailing address This portion of card should be completed and retained by the owner.
  • Page 152 BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO. 369 MANCHESTER NH POSTAGE WILL BE PAID BY ADDRESSEE Attn: Warranty Department Raytheon Marine Company 676 Island Pond Road Manchester NH 03109-9953 Note: This information is held by Raytheon Marine only and shall not be made available to any other companies. Raytheon Marine may send you mailshots/details of any new products.
  • Page 153 Detach and mail this portion within 48 hours. 48 hours. 48 hours. 48 hours. 48 hours. To validate the warranty, the customer or dealer must fill in the requested information below and mail to address shown on front. Retain other portion for your records. Purchased from Dealer address Installed by...

This manual is also suitable for:

Hsb series

Table of Contents