Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dahua Technology ITC1652
Summary of Contents for Dahua Technology ITC1652
- Page 1 All-in-One Enforcement Camera ITC1652 Side Mounting Construction Guide...
-
Page 2: Table Of Contents
Construction Guide Table of Contents 1 Main devices in the System ........................... 1 Device List ..................................... 1 Device Introduction .................................. 1 1.2.1 All-in-One Enforcement Camera ..........................1 1.2.2 Edge Storage Device ..............................3 2 Installation Scheme ............................4 3 Installation Procedures ..........................5 Installing the Bracket and the Camera .......................... -
Page 3: Main Devices In The System
Construction Guide Main Devices in the System Device List Name Model DHI-ITC1652-AU5F-LZF1640-C1 Dahua 16MP All-in-One Enforcement Camera (with 16 mm–40 mm vari-focal DHI-ITC1652-AU5F-IRL7ZF1640-C1 lens) DHI-ITC1652-AU5F-IRL8ZF1640-C1 Side mounting brackets DHI-ITSZJ-3101-M Pole mounting bracket DH-PFA150 Edge Storage Terminal DHI-ITSE1200-TA Device Introduction 1.2.1 All-in-One Enforcement Camera... - Page 4 Construction Guide Terminal blocks Table 1-2 Interfaces of the terminal block Pin No. Description Flashing light 1 triggers output F1+ Flashing light 1 triggers output F1- F1– Flashing light 2 triggers output F2+ Flashing light 2 triggers output F2- F2– Flashing light 3 triggers output F3+ Flashing light 3 triggers output F3- F3–...
-
Page 5: Edge Storage Device
Construction Guide 1.2.2 Edge Storage Device Device front Device rear Table 1-3 Key interfaces of the edge storage device Name Description Power switch POWER 12 VDC power interface DV 12V Reset button. Press and hold the button for 10 s to restore the device to factory settings. RESET 2 ×... -
Page 6: Installation Scheme
Construction Guide Installation Scheme Installation diagram Triggering line 23 m Side mount the camera on the pole mounting bracket, and attach the bracket to the pole at a height of 6 meters. The recommended horizontal distance is 23 meters, and 4 lanes are covered. ... -
Page 7: Installation Procedures
Construction Guide Installation Procedures Installing the Bracket and the Camera Attach the connector of the side mounting bracket to the bottom of the camera enclosure. Secure the base of the side mounting bracket to the pole mounting bracket. Attach the side mounting bracket to the camera. -
Page 8: Connecting The Cables
Construction Guide Use hold loops to secure the pole mounting bracket to the pole. Connecting the Cables Overall Wiring... -
Page 9: Connecting The Power Cord
Construction Guide 3.3.1 Connecting the Power Cord DANGER Cut off the power supply before connecting the cables. Power supply: 220 VAC. Connect live wire to L port, neutral wire to N port and grounding wire to PE port. ... -
Page 10: Commissioning
Construction Guide Commissioning Initializing the Camera Log in to the webpage of the camera (default IP address: 192.168. 1.108). Follow the on-screen instructions to modify the password and IP address of the camera. After the initialization is complete, go to the home page, and then download and install the plug-in. - Page 11 Construction Guide The license plate is horizontal and level in the monitoring image. On the Live page, click to adjust the lens. Loose the screw on the bottom of the side mounting bracket with an Allen wrench to adjust the position of the camera.
-
Page 12: Adjusting The Focus
Construction Guide Adjusting the Focus We recommend you perform focusing in daytime. Place a traffic cone 23 meters away from the pole, and hang the license page on the cone. Adjust the focus through Autofocus, and observe the definition of the image at the same time. Use the zoom function to zoom in to the position where the license plate is placed. - Page 13 Construction Guide Make sure the edge and each character on the license plate is clear to human eyes in the image, and defocus is not allowed.
-
Page 14: Configuration On The Webpage
Construction Guide Configuration on the Webpage This section only introduces the configuration steps of ANPR function. For more functions, see the user’s manual. Synchronizing the Time On the home page, select Setting > System > General > Date & Time. Set the time zone to Beijing, click Sync PC or manually enter the time to synchronize the system time, and then click Save. -
Page 15: Configuring The Illuminator
Construction Guide Configuring the Illuminator On the home page, select Setting > Peripheral > External Light. Set the parameters for the external light. For example, if a strobe light is connected to F7+ and F7- ports, you need to select Strobe for port 7. - Page 16 Construction Guide...
-
Page 17: Edge Storage Device Itse0804
Construction Guide Edge Storage Device ITSE0804 This section only introduces the configuration steps of snapshots capturing and video storage. For more functions, see the user’s manual. Initializing the Device Log in to the webpage of the device (default IP address: 192.168. 0.108) Follow the on-screen instructions to modify the password and IP address. -
Page 18: Synchronizing The Time
Construction Guide Synchronizing the Time On the home page, select Setting > System > General > Date & Time. Set the time zone to Beijing, click Sync PC or manually enter the time to synchronize the system time, and then click Save. Configuring the IP Address On the home page, select Setting >... -
Page 19: Adding Camera
Construction Guide Adding Camera On the home page, select Setting > Add Camera > Add Camera. Select and then enable the channel, enter the IP address, username and password, and then click Save. You can click Refresh after several seconds to check if the camera is successfully added to the edge storage device. -
Page 20: Searching For Videos And Snapshots
Construction Guide Configure capturing On the home page, select Setting > Storage > Record > Snapshot. Select the checkbox to enable snapshot for the corresponding channel, and then click Save. Searching for Videos and Snapshots On the home page, click Search. Select Vehicle or Record, configure the search time, channel and more parameters, and then click Search.