Page 1
The power behind competitiveness Grid-tie Transformerless Solar Inverter M70A_262 Operation and Installation Manual English 繁體中文 www.deltaww.com...
DELTA ELECTRONICS, INC. Service engineers and end users may not divulge the information contained herein or use this manual for purpose other than those strictly connected with correct use of the product.
This user manual provides important instructions for Delta grid-tie transformerless solar inverter. The product is designed, tested, verified, and certified according to international safety requirements, certifications, and standards but precautions must be observed when installing and operating the product.
Safety 1.2.2 Symbols This section describes the definition of the symbols in this manual. In order to prevent both personal injury and property damage, and to ensure long-term operation of the product, please read this section carefully and follow all the safety instructions while you use the product. DANGER! - This warning indicates an immediate hazard which will lead to death or serious injury.
Page 11
Safety INFORMATION - An exclamation mark enclosed in a double circle indicates additional important information is contained in the following section and the user should follow the instructions to prevent any hazards. DANGER : ELECTRICAL HAZARD!! - This warning indicates an immediate electrical hazard that unheeded can lead to death or serious injury.
The user manual is valid for the following device types: • M70A_262 This user manual must be followed during installation, operation, and maintenance. DELTA reserves the right to make modifications to the content and technical data in this user manual without prior notice.
⑦ ⑧ ⑨ ⑩ Figure 2-1: Components Table 2-1: Packing list M70A_262 Object Description Delta Solar Inverter 1 pc Solar inverter Wall mounting bracket 1 pc Mounting Bracket (Material: Aluminum/Thickness: 3mm) Important instructions for solar inverter. User Manual 1 pc Safety instructions should be followed during installation and maintenance.
Page 14
Introduction External Antenna Wi-Fi module Fans Bracket SUB_1G Antenna wiring port DC Switch AC Output RS-485 Toggle Latch Wi-Fi Antenna DC Input (H4) (option) x 12 strings Figure 2-2: Overview...
Page 15
(防護等級/防护等级) Over Voltage Category : AC:III / DC:II (過電壓等級/过电压等级) Made in China Authorized representative VDE-AR-N 4105 Delta Electronics (Netherlands) B.V. Zandsteen 15, 2132 MZ Hoofddorp, VDE-AR-N 4110 The Netherlands IP65 60 seconds Figure 2-3: Rating label Table 2-2: Rating label explanation...
Page 17
Introduction ⑭ ⑬ ⑦ ⑮ ⑫ ⑪ ④ ⑨ ⑩ ⑥ ① ③ ⑤ ② ⑧ Figure 2-5: layout Table 2-3: layout description Component Component Component 2.8” cable opening for AC Communication port Outter fan Type II DC SPD Wi-Fi (option) AC terminal Type II AC SPD Wi-Fi gland...
Installation 3 Installation CAUTION ! - In some locations, mounting the inverter in direct sunlight may cause the inverter to enter a thermal derating mode. To eliminate this concern, a shade structure over the inverter chassis may be necessary. WARNING ! - Do not install the unit near or on flammable surfaces.
Installation 3.1 Unboxing & Review Unpacking the case, please follow the order of Figure 3-1. It could be transported by 2 people (Figure 3-2) . For ground mount installation It is recommended to install the grounded brackets first at this step. For detailed installation methods, Need more than please see section 3.2.2.
Page 20
Installation Prohibit to force with Prohibit to force with Prohibit to force with fan shutter. DC connector. DC switch. Prohibit to force with AC gland. Figure 3-2: Handle position for handling...
Installation 3.2 Mechanical Installation This unit is designed to be wall-mounted per Section 3.2.1 or ground mounted Section 3.2.2. 3.2.1 Vertical Wall Mount Refer to Figure 3-4 to Figure 3-9. 1. Ensure the surface to which the unit is to be mounted is sufficiently strong enough to carry the weight.
Page 22
Installation 699 mm 264 mm Figure 3-3: Inverter dimensions unit: mm Figure 3-4: Mounting bracket dimensions...
Page 23
Installation Required position of at least 8 screws for mounting bracket Figure 3-5 : Positions of mounting screws >200mm Figure 3-6: Permitted mounting positions...
Page 25
Installation Wall Without Clapboard >200mm >200mm >300mm >600mm >300mm >60mm * >60mm * * If the installation location has a risk of flooding or accumulated snow, please raise the appropriate height of the inverter. Install Clapboard Clapboard dimension 200mm >830mm >150 >150 >380mm...
Installation 3.2.2 Ground Mount (Option) Buy the spare parts of grounded brackets if ground mounted. 1. Ensure the grounded base to which the unit is to be mounted is sufficiently strong enough to carry the weight. 2. The grounded base horizontally (perpendicular to the floor), and mark required mounting hole locations per Figure 3-11.
Page 27
Installation Φ15 mm 310 mm 458 mm height * * If the installation location has a risk of flooding or accumulated snow, please raise the appropriate height of the inverter. Figure 3-11: To secure inverter grounded brackets to ground-mounting base...
Installation 3.3 Door In order to ensure the normal long-term operation of the inverter, please follow the procedures in Section 5.1 to open and close the door. If the installation space is too narrow for the wiring operation, please remove the door according to Figure 3-12.
Installation 3.4.1 AC Grid Types and Connections ATTENTION The default AC Grid connection is 3Ø-3W. It can also connect 3Ø-4W with Neutral (N). The inverter will operate from the following grid connections without need of an external transformer: TNC system TNC-S system 230/400V 230/400V...
Page 30
Installation M70A_262 support Cu stranded wire, Cu flexible conducor, Al stranded wire and aluminum solid (include sector wire). Cu stranded Cu flexible wire Al stranded Aluminum solid (need press with terminal) (sector) * • Cu: The Cu flexible wire need stamp with terminal, for the other model wiring with bear wire is available.
Installation Figure 3-13: AC Gland with multiple inlet Table 3-1: Cable size comparison table Sizes of Cables (mm) Torque (N• m) Dimension of P (mm) 51-57 2550 mm 43-50 1962 mm 36-43 1450 mm 30-36 1017 mm 26-30 706 mm 3.4.4 AC Side –Prewire Set-Up Prior to installing conductors on terminal complete the following procedure to make terminals ready for connections.
Installation 3.4.5 AC Wiring Refer to Figure 3-12 in Section 3.4 for the procedure to prepare AC conductors for connection to the AC terminals. Ensure the AC conductors used are sized to the correct ampacity per NEC or other local code. After inserting conductor, torque terminal nut by 31 N •...
Installation 3.5 Electrical Installation for DC Wiring DANGER : ELECTRICAL HAZARD!! - PV array converts sunlight into electric power with high DC voltage and high DC current which can cause dangerous electrical shock hazard! - Use an opaque material to cover the PV array before wiring or cabling. - Ensure the correct polarities are connected when DC cabling is applied.
Installation 3.5.1 DC Wiring Installation Please read the following instructions for connecting DC connector : • Ensure the DC conductors used are Cu and sized to the correct ampacity per NEC or other local code • Strip off all wires for 6.5~7.5 mm. •...
Page 35
Installation SWITCH 1 SWITCH 2 Figure 3-16: location of H4 connectors to connect array wiring (DC)
Page 36
Installation PUSH PUSH To prop up connectors, frames should be installed beneath. Figure 3-17: Installation methods for protective frame...
Installation 3.5.2 Equipment Grounding To ground the inverter, please crimp the grounding wire to ring terminal lug and fix it on the grounding point shown as figure 3-18. Screw torque: M6/ 3.9 N•m Figure 3-18: Mount the equipment grounding...
Figure 3-19 ~ 3-21. ATTENTION - Always keep nut and screws properly tightened on the case. Water leakage may cause serious damage. Contact DELTA service when lack for nut and screws. - Store the nut for spare usage. Antenna Location Save the nut after antenna installed.
Page 39
Installation >20cm There must be no obstacles within 20 cm around the antenna. Keep antenna pointing upright. Figure 3-20: Attentions of installing antenna...
Page 40
Installation 1. Turn the antenna counterclockwise by about 45 degrees. 2. Put on the antenna bracket. 3. Turn the antenna to the proper position. 4. Tighten the 3 screws to antenna bracket. ① ② ③ ④ Screw locations * Screw torque: M4 / 0.98 N • m Figure 3-21: Install antenna bracket ATTENTION - Please refer Data Collector manual for connection of Data Collector.
Installation 3.7 Communication Module Connections The communication module of M70A is shown in Figure 3-22. It provides VCC, RS-485, dry contact, EPO, and Digital Input terminals for use in various applications. Details for each are presented below. There's a 12VDC source between VCC & GND for use with external device. VCC *1 &...
Page 42
Installation Please refer to the chapter 5.1 and open the door, the communication module is at the red circle that is shown in Figure 3-23. Figure 3-23: Location and access to Communication Module...
Installation 3.7.1 RS-485 Connection The pin definition for the RS-485 terminal block is shown in Table 3-2. - Pins 1 and 2 provide a 12VDC / 0.5A bus for use with accessories. - Pins 3 and 5 are both connected to the DATA+ input. - Pins 4 and 6 are both connected to the DATA - input.
3.7.2 EPO Function & Digital Input The communication Module has an Emergency Power Off function (EPO). Users can customize EPO function in APP or Delta Solar System (DSS). VCC K0 K1 K2 K3 K4 K5 K6 Figure 3-25: EPO function terminal block Once enabled, the EPO function can be used to turn off the inverter via a NO relay contact connected across terminal [VCC &...
Installation 3.7.3 Dry Contact Connection M70A_262 provide dry control contact pairs that may be used to control external devices based on the status of operation of the inverter. The terminal block for this function is shown in Figure 3-26. The terminals marked in the figure identify the dry contact connection.
Installation 3.8 On-Site Insulation Test For customers who want to do on-site insulation test, please make sure: 1. The DC switches are in “OFF” position. 2. Apply one probe to the positions shown in Figure 3-27, the other to the ground. It might cause damages to the inverter if probes are applied to inappropriate positions.
Commissioning 4 Commissioning CAUTION : HOT SURFACES, DO NOT TOUCH! - Use care to avoid hot surfaces when operating the product! - Do not perform any task until the unit cools down or appropriate personal protection gear is worn. 4.1 Display Operation Introduction M70A_262 with 3 LEDs allow visual display of the inverter’s data and status as shown in Figure 4-1.
Commissioning 4.2 Auto ID Commission Tool The Auto ID function could set all inverter IDs at monitoring center after wiring RS-485. ATTENTION Please download the software from the following website: https://mydeltasolar.deltaww.com/dl_installer_guide.php?f=autoid 4.2.1 Auto ID Setting Open the software 1. Select COM Port and click 2.
Page 50
Commissioning The numbers of ID setting less than amounts of inverter, status show False. The numbers of ID setting more than amounts of inverter, status show False. Figure 4-3: False of auto ID setting by tool...
Commissioning 4.2.2 Set ID To adjust the ID order, please follow the settings below. 1. Enter the ID you want to change . 2. Click to complete. Figure 4-4: Steps of set ID The wrong ID setting of overlapping. Figure 4-5: False of set ID...
Commissioning 4.2.3 Set Country Set country by the AUTO ID. 1. Entry the local country ID number. 2. Click the to complete country setting. Figure 4-6: Steps of set country Enter as a country that does not exist. Figure 4-7: False of set country...
Commissioning 4.2.4 Synchronize time Synchronize time by Auto ID tool. Click the to complete time setting. Figure 4-8: Steps of synchronize time Interference problem make sync time fail, please try again. Figure 4-9: False of synchronize time...
Commissioning 4.3 Delta Function Setting Delta offers two settings: DSS and APP (MyDeltaSolar) Please go to the following link to refer to the setting method manual. DSS: https://mydeltasolar.deltaww.com/manual/eng/SUB_1G/DSS.pdf APP (MyDeltaSolar): https://mydeltasolar.deltaww.com/?p=product_manual Data Collector > PPM DC1_100 Operation and Installation Manual...
Maintenance 5 Maintenance Please check the unit regularly. If there are any impaired or loose parts, please contact your solar installer. Ensure that there are no fallen objects in the path of the heat outlet. WARNING ! - Prior to beginning any maintenance procedures outside AC breaker and DC switch off to avoid risk of electrical shock! 5.1 Open and Close the Door In order to guarantee proper long-term operation of the inverter, the following...
Page 56
Maintenance ① ② * Screw torque: M4 / 0.98 N•m ③ ⑤ ② ④ ① Figure 5-1: Opening and closing the door...
Page 57
Maintenance ATTENTION - After opening the door, please make sure the door is fixed by hexagon driver to avoid strong wind breaking it. Figure 5-2: To secure door by hexagon driver...
Maintenance 5.2 Replacement of Surge Protection Devices (SPD) M70A_262 have the surge protection device (SPD) at both AC and DC side as shown in Figure 5-3. DC SPD AC SPD Figure 5-3: AC and DC SPD modules...
Page 59
Maintenance Surge protection devices (SPD) are designed to protect sensitive circuit elements of the inverter from damage caused by lightning and other electrical transients/surges, as such they are sacrificial components and periodically, may need replacement. The SPDs are located in the inverter. If a warning message “AC Surge”...
Page 60
Maintenance • Accessing the door 1. Switch DC and AC power off and wait until LED display turns off. 2. To access the door, use procedure found in Section 5.1.1 Do not leave the door opened for long periods of time. •...
Page 61
Maintenance DC SPD AC SPD * Screw torque: 0.8 N•m Please use manual pre-tighten before attaching. Figure 5-5: Steps of changing SPDs...
Page 62
Maintenance AC SPDs * A: Screw torque 2.45 N •m * G: Screw torque 0.8 N •m Figure 5-6: Remove wirings as connectors of AC SPD *Wi-Fi (option) DC SPDs * A: Screw torque 2.45 N • m * G: Screw torque 0.8 N • m Figure 5-7: Remove wirings as connectors of DC SPD...
Maintenance 5.3 Smart Fans Replacement and Filter Cleaning M70A_262 is provisioned with processor-controlled "smart fans" for cooling of the electronics. This section provides procedures for cleaning filters associated with these fans, and instructions for field replacement of the fans. The fans utilized have high reliability ratings and coupled with use of processor controls provide a "smart"...
Page 64
Periodic fan and filter cleaning is required to insure long life and reliability. - The time period between cleanings depends on the quality of the environment. - Under normal duty use, Delta recommends smart fans and filters be cleaned every 4 months - For very dusty locations, it may be necessary to clean the fans and filters quarterly or monthly.
Maintenance WARNING ! - Prior to beginning any maintenance procedures outside AC breaker and DC switch off to avoid risk of electrical shock! 5.3.1 Power Module (PM) Fan Tray The inverter electronics are convection cooled. The primary equipment used for this function consists of a fan tray located in a plenum within the inverter.
Page 66
Maintenance * Screw torque required for assembling: 0.98 N•m ① ② snap-fit ③ * Screw torque required for assembling: 0.6 N•m Figure 5-10: Disassembling fan tray from PM chassis...
Maintenance 5.3.2 Internal Fan 1 Procedure to remove Internal Fan 1 (1) Remove the B cover. (2) Loosen two self-retaining screws shown in Figure 5-11 and remove the fan cabinet. (3) Disconnect the power connector on the DC SPD board. (4) Lift the entire fan assembly.
Page 68
Maintenance * Screw torque required for assembling: 0.8 N•m Figure 5-12: Take off the internal fan 1 * Screw torque required for assembling: 0.6 N•m Figure 5-13: Replace with a new fan...
Maintenance 5.3.3 Internal Fan 2 Procedure to remove Internal Fan 2 (1) Loosen two self-retaining screws shown in Figure 5-14 and remove the fan cabinet. (2) Disconnect the power connector on the comm. board. (3) Lift the entire fan assembly. (shown in Figure 5-15) (4) Clean assembly or replace with a new fan.
Page 70
Maintenance * Screw torque required for assembling: 0.8 N•m Figure 5-15: Take off the internal fan 2 * Screw torque required for assembling: 0.6 N•m Figure 5-16: Replace with a new fan...
Maintenance 5.4 De-Commissioning When necessary to remove the inverter from active operation for maintenance or replacement, follow the instructions below. DANGER : ELECTRICAL HAZARD!! To avoid serious injury, please follow the procedure below. - Switch off external AC circuit breaker or switch to disconnect the electrical grid from the inverter chassis.
Page 72
Maintenance CAUTION : HOT SURFACES, DO NOT TOUCH ! - Use care not to touch hot surfaces if the inverter is just shutting down. - Do not perform any task until the product cool down sufficiently. CAUTION : POSSIBILE INJURY ! M70A_262 weighs more than 69 kg.
Error Message and Trouble Shooting 6 Error Message and Trouble Shooting While Delta Electronics endeavors to build electronic products to very high standards of reliability, there will arise instances where the inverter may not operate properly. When such a condition is encountered, please follow the instructions in the Troubleshooting Guide (Tables 6-1, 6-2, and 6-3) to attempt to clear the fault.
Error Message and Trouble Shooting 6.2 Fault Codes (Inverter Fault) Table 6-2A: Fault Codes (inverter fault) & Messages Message Description Action Injection Contact customer service for Utility waveform is abnormal technical support (F01, F02, F03) Temperature One of inner ambient NTC and Check the installation ambient and High inverter module NTCs is over...
Page 75
Error Message and Trouble Shooting Table 6-2B: Fault Codes (inverter fault) & Messages Message Description Action Red COMM The internal communication Contact customer service for Fault connection is disconnected technical support (F22) DSP COMM The communication Fault Check the connection interface RS-485 connection is disconnected (F23) 1.
Error Message and Trouble Shooting 6.3 Warning Codes (Field Warning) Table 6-3A: Warning Codes (Field warning) & Messages Message Description Action DC Voltage Check the voltage connection to the Input voltage is under the limit inverter terminal (W01) 1. Check the installation ambient and environment 2.
Technical Information 7 Technical Information Table 7-1A: Specifications Model M70A_262 DC Input Occasionally Max. voltage 1100 V * Operating Voltage Range 200 - 1000 V MPP Voltage Range (Full Power) 460 - 900 V * Start Voltage > 250 V Rated Voltage 600 V Max.
Page 78
Technical Information Table 7-1B: Specifications Model M70A_262 Efficiency Peak efficiency 98.8 % 98.4 % Euro efficiency Information Communication Port RS-485 / SUB_1G / Wi-Fi (optional) Regulation IEC 62109-1/-2 VDE-AR-N 4110 EN 61000-6-2 NB/T 32004: 2018 EN 61000-6-3 GB/T 19964: LVRT VDE-AR-N 4105 CNS 15382 VDE 0124-100...
Page 79
Technical Information Efficiency of M70A Output voltage at 400Vac Efficiency(%) Pn=70kW 100% 520V 600V 800V 100% Output Power (%) Figure 7-1: Efficiency Curve...
Page 80
Technical Information Power Derating Curve with Ambient Temprature Output voltage at 230Vac / 400Vac PF=1 P/Pn(%) Pn=70kW 110% 100% 90 % 80 % 70 % 60 % 460V 520V 50 % 600V 720V 800V 40 % 900V 30 % 20 % Ambient Temperature (°C) Figure 7-2: Power Derating Curve with Ambient Temprature (PF=1)
Page 81
Technical Information Power Derating Curve with Ambient Temprature Output voltage at 230Vac / 400Vac PF=0.9 P/Pn(%) Pn=70kW 110% 100% 90 % 80 % 70 % 60 % 460V 520V 50 % 600V 720V 800V 40 % 900V 30 % 20 % Ambient Temperature (°C) Figure 7-3: Power Derating Curve with Ambient Temprature (PF=0.9)
Page 82
Technical Information Apparent Power Derating Curve with Ambient Temprature Output voltage at 230Vac / 400Vac PF=0.9 S/Sn(%) Sn=70kVA 110% 100% 90 % 80 % 70 % 60 % 460V 520V 50 % 600V 720V 800V 40 % 900V 30 % 20 % Ambient Temperature (°C) Figure 7-4: Apparent Power Derating Curve with Ambient Temprature (PF=0.9)
Technical Information Appendix: Assembly Note ③ ④ ⑤ ① ② ⑥ Appendix-1: Assembly Note-1 Location Screw torque Filter 10 kgf-cm (0.98N• m) Fan Tray 6 kgf-cm (0.6N•m) Antenna 12 kgf-cm (1.2N•m) Antenna Bracket (M4) 10 kgf-cm (0.98N•m) Grounded Bracket 250 kgf-cm (24.5N•m) Grounding (M6) 40 kgf-cm (3.9N•m)
Page 84
Technical Information ③ ① ② ④ ⑤ H4CFC4D-MS H4CMC4D-MS Appendix-2: Assembly Note-2 Location Screw torque Conductor cross-section Internal Fan 2 Cover 8.0 kgf-cm (0.8N•m) Internal Fan 2 Tray 6 kgf-cm (0.6N•m) Internal Fan 1 Cover 8.0 kgf-cm (0.8N•m) Internal Fan 1 Tray 6 kgf-cm (0.6N•...
Page 85
Technical Information ① ① ④ ⑤ ④ ⑥ ② ③ ③ ② ⑤ ④ Appendix-3: Assembly Note-3 NO Location Screw torque Conductor cross-section DC SPD board A: 25 kgf-cm (2.45N•m) G: 8.0 kgf-cm (0.8N •m) AC SPD board AC Cover 8.0 kgf-cm (0.8N•m) Toggle Latch 25 kgf-cm (2.45N•m)
Page 87
The power behind competitiveness 三相併網型變流器 M70A_262 操作手冊 English 繁體中文 www.deltaww.com...
產品介紹 ⑭ ⑬ ⑮ ⑦ ⑫ ⑪ ④ ⑨ ⑩ ⑥ ① ③ ⑤ ② ⑧ 圖2-5 : 配線箱架構圖 表2-3 : 配線箱架構圖內容描述 Component Component Component 2.8” cable opening for AC Communication port Outter fan AC terminal Type II DC SPD Wi-Fi (option) H4 connectors Type II AC SPD...
安裝 3.4.5 交流配線 有關用於連接交流端子的交流導線準備步驟,請參閱第3.4節中的圖3-12。 確保所使用的交流導體尺寸符合NEC或當地電力法規的規範,參閱圖3-12。 After inserting conductor, torque terminal nut by 31 N • m (PE: 14.7 N • m) Bottom AC entry AC terminal Up to 2.8 "trade size gland 圖 3-14: 交流端子位置圖 圖3-14為交流導管安裝處和連接機器內部交流端子的位置圖: - 如第3.4.4節所述,卸下所有交流端子上的六角螺絲。 - 確保將正確的導線連接到相應的端子位置。 - 插入導線後,使用8 mm六角扳手鎖緊L1,L2,L3,N端子,安裝鎖附扭力值...
維護 AC SPDs * A: Screw torque 2.45 N •m * G: Screw torque 0.8 N • m 圖 5-6 : 移除AC SPD 螺絲與排線 *Wi-Fi (option) DC SPDs * A: Screw torque 2.45 N •m * G: Screw torque 0.8 N • m 圖...
技術資料 7 技術資料 表 7-1A: 規格 Model M70A_262 直流輸入 1100 V * 最大輸入電壓 200 - 1000 V 工作電壓範圍 460 - 900 V * MPP 電壓範圍 (全功率) > 250 V 啟動電壓 額定電壓 600 V Each MPPT: 26 A, Total: 156 A 最大輸入電流 Each MPPT: 15.7 kW, 最大輸入功率...