Advertisement
4.3 The warning message
Alarm code
Description
Stitch counter alarm
Trimming counter
alarm
Power off alarm
Safety switch alarm
The speed controller
is abnormal
Stepper motor out of
position
4.4 Error mode
If the error code appears, please check the following items first:1.Make sure the machine has been connected correctly; 2.
control box match with the machine head. 3. Confirm factory reset is accurate
Error Code
Description
Arm shaft motor
Err-01
hardware overcurrent
Err-03
System undervoltage
Overvoltage during
Err-04
shutdown
Overvoltage during
Err-05
operation
Electromagnet circuit
Err-06
failure
Current detection circuit
Err-07
failure
Err-08
Arm shaft motor stalled
Panel communication
Err-10
failure
Err-11
Head stop signal failure
Arm shaft motor initial
Err-12
angle detection failure
Arm shaft motor zero
Err-13
position fault
Master control eeprom
Err-14
components read/write
failure
Arm shaft motor
Err-15
overspeed protection
Err-16
Arm shaft motor reverse
Master control restart
Err-17
failure
Err-18
Arm shaft motor overload
Alarm for oil shortage
Err-20
every 8 hours
The stitch counter reaches the limit. Press
The trimming counter reaches the limit. Press
Please wait for 30 seconds, then turn on the power switch
Adjust the machine to the correct position.
Disconnect the power supply and check whether the line contact of the speed controller is
detached
Adjust the parameter item P123 to check the installation position of the stepping motor
1.
Turn off the system power, and turn it on again after 30 seconds.
2.
Please enter P61 to check the initial angle of the arm shaft motor.
3.
Check whether the arm shaft motor encoder and electronic control are damaged or in other poor
conditions. If so, replace them in time.
4.
If the system still does not work properly after troubleshooting and restart.
Please contact your local service provider or call 4008876858.
Disconnect the power supply of the controller and check whether the input power supply voltage is
lower than 176V. If so, please restart the controller after the voltage returns to normal. If the voltage
returns to normal, it still does not work properly after the controller starts up.
Please contact your local service provider or call 4008876858.
Disconnect the controller power and check whether the input power voltage is higher than 264V. If
so, please restart the controller after the voltage returns to normal. If the voltage returns to normal, it
still does not work properly after the controller starts up.
Please contact your local service provider or call 4008876858.
1.
Turn off the system power, check whether the electromagnet connection is correct and whether
there is any loose or damaged part. If so, replace it in time.
2.
Unplug the 14-pin plug on the electric control to confirm whether the electric control is normal. If
the electric control is normal, please check whether the electromagnetic circuits are damaged.
3.
If the system still does not work after troubleshooting and restart.
Please contact your local service provider or call 4008876858.
Turn off the system power, and turn on the power again after 30 seconds to see whether it can work
properly. Try a few times again. If the fault occurs frequently, please contact your local service
provider or call 4008876858.
1.
Please check whether there is any foreign object wrapped around the machine head, whether
there is any thread residue stuck in the rotating shuttle, and whether the eccentric wheel of the
machine is stuck.
2.
Disconnect the power supply of the controller and check whether the input plug of the arm shaft
motor power supply is detached, loose, or damaged.
3.
Please enter P61 to check the initial angle of the arm shaft motor.
4.
If the system still does not work properly after troubleshooting and restart.
Please contact your local service provider or call 4008876858.
1.
Please check whether the connection between the operation panel and the electric control is
drops off, loose, or broken.
2.
Please check whether the connection cable of the pedal speed controller is drops off, loose, or
damaged.
3.
If the system still does not work properly after troubleshooting and restart.
Please contact your local service provider or call 4008876858.
1.
Check whether the connection between the arm shaft motor encoder and the controller is loose.
2.
Replace the arm shaft motor encoder.
3.
If the system still does not work properly after troubleshooting and restart.
Please contact your local service provider or call 4008876858.
1.
Please enter P61 to check the initial angle of the arm shaft motor.
2.
Please try 2-3 times again after power off. If it still fails.
Please contact your local service provider or call 4008876858.
1. Turn off the power of the system, check whether the arm shaft motor encoder connector is loose,
or drops off. Restore it to normal and restart the system.
2. Replace the arm shaft motor encoder.
3. If the system still does not work properly after troubleshooting and restart.
Please contact your local service provider or call 4008876858.
Turn off the system power, and then turn on the power again after 30 seconds. If the controller still
does not work properly, please contact your local service provider or call 4008876858
Check whether the arm shaft motor is stalled. If not, please contact your local service provider or call
4008876858.
Check whether the oil level of the machine is sufficient. If the problem is still not resolved after filling
up the oil volume, please contact your local service provider or dial 4008876858.
第 9页共 10 页
Corrective
key to cancel the alarm and reset the counter.
key to cancel the alarm and reset the counter.
Solution
Confirm that the
Advertisement
