Advertisement
4 System parameters setting list
4.1 Parameter mode
1、In the standby state ,press
2、Press corresponding key
3 、 When the parameter values have increased and decreased, parameter interface flash. Short press
parameters .Long press
key to exit parameter interface, return to standby model.
NO.
Range
Default
P 0 1
200~5000
3800
P 0 2
1~100
P 0 3
0/1
P 0 4
200~3000
1800
P 0 5
200~3000
1800
P 0 6
200~3000
1800
P 0 7
200~4000
3700
P 0 8
0/1
P 0 9
0/1
P 1 0
1~9
P 1 1
100~800
400
P 1 2
-8~8
P 1 3
200~4000
3200
P 1 4
100~800
200
P 1 5
0~3
P 1 6
0~9999
P 1 7
0~9999
P 1 8
0~50
P 1 9
200~4000
2000
P 2 0
0~50
P 2 1
0~50
P 2 2
1~4
P 2 3
0~4095
1100
P 2 4
0~4095
550
P 2 7
10~100
P 2 8
0~359
130
P 2 9
0~359
320
P 3 0
0~359
130
P 3 1
0~359
340
P 3 2
0~100
P 3 3
0~80
P 3 4
0/1
P 3 5
0~3000
800
P 3 6
0~3000
1500
P 3 7
0~3000
P 3 8
0~4000
1000
key to enter the parameter modes.
and key
to adjust the corresponding parameter.
Free seam velocity
56
Start sewing slight lift force adjusting
1
Needle stop position selection (1:up; 0: down)
Start back tacking speed
End back tacking speed
Continuous back sewing speed (W sewing)
Multiple seam velocity
0
Stitching presser foot micro-lift presser foot switch
0
Soft start switch (0:off; 1: on)
2
Slow-start stitch count
Slow-start sewing speed
2
1/2 multi-function key(2-1/2 4-1/4 8-1/8 -2-(-1/2) -4(-1/4) -8-(-1/8))
Maximum speed of reverse stitching
Stitch compensation speed
Button stitching mode (0- close 1- continuous stitching according to the time 2- half stitching 3- one
1
stitching)
Thickness detection 0 point value
0
0
Thick material height
5
A terrier number of threads
A terrier speed
5
Compensation value of over-stalk needle distance
Thickness detection sensitivity
0
4
A terrier trajectory
Analog quantity of pedal wire cutting position 1(turn off automatic lifting foot pedal wire cutting
position)
Analog quantity of pedal wire cutting position 2(start automatic lifting foot pedal wire cutting position)
36
Efforts to cut line
The starting Angle of the clamping line when the front reinforcement joint and the W joint are opened
The clamping end Angle of front reinforcement joint and W joint when opened
The starting Angle of the clip when the front tight seam is opened
The clamping end Angle when the front tight seam is opened
80
Raise duty cycle gently with presser foot
55
Clamp wire output
1
Oil level detection switch
The speed of the first stitch
The speed of the second stitch
0
The speed of the third stitch
Front reinforcement/W seam first stitch speed limit
第 6页共 10 页
key to save the modified
Description
Advertisement
