Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Baumatic BHG300.6SS
Summary of Contents for Baumatic BHG300.6SS
- Page 1 BHG300.6SS 30 cm 2 Burner Gas Hob INSTRUCTION MANUAL...
- Page 2 The manufacturer shall not be held responsible for any damages to persons or property caused by incorrect installation or use of the appliance. MODEL: BHG300.6SS The Manufacturer shall not be held responsible for any inaccuracies in this handbook due to printing or transcription errors;...
- Page 3 DESCRIPTION OF THE BURNERS MODEL: MODEL: BHG300.6SS 2 Rapid gas burner of 3000 W 3 Auxiliary gas burner of 1000 W 7 Enamelled steel pan support 9 Burner n° 2 control knob 10 Burner n° 3 control knob Attention: This appliance has been manufactured for domestic use only and it's use by private...
- Page 4 1) BURNERS Burners Power ratings Pan Ø in cm A diagram is printed above each knob on the Rapid 3000 20 ÷ 22 front panel. This diagram indicates to which Auxiliary 1000 10 ÷ 14 burner the knob in question corresponds. After having opened the gas mains or gas bottle tap, light WARNINGS: the burners as described below:...
- Page 5 WARNINGS AND ADVICE FOR THE USER: Use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating the mechanical aeration device (extraction hood or electric fan fig 4 and fig 5).
- Page 6 CLEANING IMPORTANT: WARNINGS: Comply with the following instructions, before Always disconnect the appliance from the gas remounting the parts: and electricity mains before carrying out any - Check that burner head slots “T” (fig. 6) have cleaning operation. not become clogged by foreign bodies. 2) GAS HOB - Check that enamelled burner cap “C”(fig.
-
Page 7: Installation
INSTALLATION TECHNICAL INFORMATION FOR THE established by the provisions governing such appliances. INSTALLER Installation, adjustments of controls and 4) FIXING THE HOB maintenance must only be carried out by a qualified engineer. The hob has a special seal which prevents liquid The appliance must be correctly installed in from getting into the cabinet. -
Page 8: Gas Pressure Test
INSTALLATION I M P O RTA N T I N S TA L L AT I O N 7) GAS CONNECTION S P E C I F I C AT I O N S Before connectiong the appliance, check the The rear wall and the surfaces surrounding values on the data label affixed to the and adjacent to the appliance must be able to... -
Page 9: Electrical Connection
INSTALLATION 8) ELECTRICAL CONNECTION mm gap between its contacts. - Remember that the earth wire must not be interrupted by the circuit-breaker. IMPORTANT: the appliance must be installed following the manufacturer's - The electrical connection may also be protected instructions. The manufacturer will not be by a high sensitivity differential circuit- breaker. - Page 10 ADJUSTMENTS Always disconnect the appliance from the It is understood that only burners operating electricity main before making any adjustments. with G20 gas should be subjected to the above All seals must be replaced by the technician at mentioned adjustments. The screw must be the end of any adjustments or regulations.
-
Page 11: Replacing The Injectors
CONVERSIONS 10) REPLACING THE INJECTORS paragraphs 9. The technician must reset any seals on the regulating or pre-regulating devices. The burners can be adapted to different types of The envelope with the injectors and the labels can gas by mounting injectors suited to the type of gas be included in the kit, or at disposal to the in question. - Page 12 SERVICING Always disconnect the appliance from the Greasing the taps (see fig. 18 - 19) electricity and gas mains before proceeding If a tap becomes stiff to operate, it must be with any servicing operation. immediately greased in compliance with the following instructions: - Remove the tap.
- Page 13 SERVICING CABLE TYPES AND SECTIONS TYPE OF SINGLE - PHASE TYPE OF CABLE POWER SUPPLY H05 RR - F Section 3 x 0.75 mm Gas Hob ATTENTION!!! If the power supply cable is replaced, the installer should leave the ground wire longer than the phase conductors (fig.
- Page 14 TECHNICAL DATA ON THE DATA LABEL 2 BURNERS “ DOMINO ” Category = II 2H3+ G30 - BUTANE = 28 - 30 mbar G31 - PROPANE = 37 mbar G20 - NATURAL = 20 mbar Tot. Nom. Gas Rate = 4 kW Tot.
- Page 15 TECHNICAL DATA FOR THE APPLIANCE GAS REGULATION...
-
Page 16: Technical Assistance And Spare Parts
TECHNICAL ASSISTANCE AND SPARE PARTS Before leaving the factory, this appliance will have been tested and regulated by expert and specialised personnel in order to guarantee the best performances. Any repairs or adjustments which may be subsequently required may only be carried out by qualified personnel with the utmost care and attention. - Page 19 Kundendienst & Ersatzteile (0118) 933 6933 Deutschland 0049(0)180-5888975 E-mail: Oesterreich +43 (0) 820 / 420423 sales@baumatic.co.uk customercare@baumatic.co.uk www.baumatic.de spares@baumatic.co.uk technical@baumatic.co.uk Italy Baumatic Italia S.R.L. Website: Via Galvani N.3 www.baumatic.co.uk 35011 Campodarsego (PD) Facebook: +3904 9920 2297 www.facebook.com/baumatic.uk www.baumatic.it Republic of Ireland Holland Baumatic Benelux B.V.
- Page 20 www.baumatic.com...