Onkyo TX-NR595 Instruction Manual page 111

• The unit of distance can be changed by pressing the MODE button on the remote
controller. When using the unit "feet", the setting is available in increments of 0.1 ft from
0.1 ft to 30.0 ft. When using the unit "meter", the setting is available in increments of
0.03 m from 0.03 m to 9.00 m.
„ 4. Level Calibration
Adjust the volume level of each speaker.
Setting Item Default Value
Front Left 0 dB
Center 0 dB
Front Right 0 dB
Height Left 0 dB
Height Right 0 dB
Surround Right 0 dB
Surr Back Right 0 dB
Setting Details
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
• The setting cannot be changed if "Configuration"
- "Zone Speaker" is set to "Zone 2" and Zone 2
is on.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
• The setting cannot be changed if "Configuration"
- "Zone Speaker" is set to "Zone 2" and Zone 2
is on.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
• The setting cannot be changed if "Configuration"
- "Zone Speaker" is set to "Zone 2" and Zone 2
is on.
Contents Connections
≫
Setting Item Default Value
Surr Back Left 0 dB
Surround Left 0 dB
Subwoofer 0 dB
„ 5. Dolby Enabled Speaker
Change the settings of Dolby Enabled Speakers.
Setting Item Default Value
Dolby Enabled 6.0 ft/1.80 m
Speaker to Ceiling
AccuReflex Off
• This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby
Speaker".
111
Front Panel≫ Rear Panel≫ Remote≫
Playback Setup
≫ ≫
Setting Details
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
• The setting cannot be changed if "Configuration"
- "Zone Speaker" is set to "Zone 2" and Zone 2
is on.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-15 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Setting Details
Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between
"0.1 ft/0.03 m" and "15.0 ft/4.50 m" (0.1 ft/0.03 m
units).
• The unit of distance (ft/m) is displayed using the
unit selected for the "Distance" setting.
You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": When this function is not used
"On": When this function is used
≫