Mitsubishi Electric MELSEC-Q QnPHCPU Programming Manual page 269

INDEX
[Number]
2-degree-of-freedom PID (S.2PID)................ 9- 9
2-position ON/OFF (S.ONF) ......................... 9-83
3-position ON/OFF (S.ONF3) ....................... 9-89
[A]
Absolute value (S.ABS) .............................. 11-11
Addition (S.ADD) .......................................... 11- 1
Alarm detection inhibition (INH) ..................... 3- 8
Alarm detection (ALM) ................................... 3- 7
ALM(Alarm detection) .................................... 3- 7
Analog input processing (S.IN) ...................... 8- 1
Analog memory (S.AMR) ............................ 9-110
AUT (AUTOMATIC) ....................................... 3- 9
Auto tuning (S.AT1)...................................... 13- 4
Average value (S.AVE) ................................. 9-75
[B]
Basic PID (S.PID)........................................... 9- 1
Batch counter (S.BC) .................................... 8-28
Blend PI control (S.BPI) ................................ 9-41
Block memory................................................. 3- 6
Bumpless transfer (S.BUMP)...................... 9-108
[C]
CAB (COMPUTER AUTOMATIC BACK UP) . 3- 9
CAS (CASCADE) ........................................... 3- 9
Cascade loop.................................................. 5- 2
CCB (COMPUTER CASCADE BACK UP) ... 3- 9
Change rate limiter 1 (S.VLIMT1)................. 9-79
Change rate limiter 2 (S.VLIMT2)................. 9-81
CMB (COMPUTER MANUAL BACK UP) ..... 3- 9
CMV (COMPUTER MV) ................................ 3- 9
Compare equal than (S. ) .......................... 12- 5
Compare greater or equal (S. > ) .............. 12- 7
Compare greater than (S. >)........................ 12- 1
Compare less or equal (S. < ) ................... 12- 9
Compare less than (S. <) ............................. 12- 3
Control cycle................................................... 4- 1
CSV (COMPUTER SV).................................. 3- 9
[D]
D operation ..................................................... 1- 8
Dead band (S.DBND).................................... 9-95
Dead time (S.DED) ....................................... 9-65
Derivative operation (D operation)................. 1- 8
Deviation large alarm inhibition (DVLI) .......... 3- 8
Deviation large alarm (DVLA) ........................ 3- 8
Derivative (S.D) ............................................. 9-63
Division (S.DIV) ............................................ 11- 7
Index - 1
DMLA (Output change rate limit alarm) .........3- 8
DMLI (Output change rate limit alarm inhibition)
.........................................................................3- 8
DPNA (Negative direction change rate alarm)
.........................................................................3- 8
DPNI (Negative direction change rate alarm
inhibition) .........................................................3- 8
DPPA (Positive direction change rate alarm)
.........................................................................3- 8
DPPI (Positive direction change rate alarm
inhibition) .........................................................3- 8
DVLA (Deviation large alarm).........................3- 8
DVLI (Deviation large alarm inhibition)...........3- 8
[E]
Engineering value conversion (S.ENG) ......10-12
Inverse engineering value conversion (S.IENG)
......................................................................10-14
Error code list ................................................14- 1
Execution cycle ...............................................4- 1
[F]
Forward operation...........................................1- 5
Function generator (S.FG).............................10-1
[H]
High/low limit alarm (S.PHPL) .......................9-53
High/low limiter (S.LIMT) ...............................9-77
High selector (S.HS) ......................................9-68
HHA (Upper upper limit alarm) .......................3- 8
HHI (Upper upper limit alarm inhibition).........3- 8
How to Read Instructions ...............................7- 1
[I]
I operation .......................................................1- 7
I-PD control (S.IPD) .......................................9-33
INH (Alarm detection inhibition)......................3- 8
Input data ........................................................3- 5
Integral operation (I operation) .......................1- 7
Integral (S.I)....................................................9-61
Inverse function generator (S.IFG)...............10- 3
[L]
LCA (LOCAL AUTOMATIC)...........................3- 9
LCC (LOCAL CASCADE)...............................3- 9
LCM (LOCAL MANIPULATED)......................3- 9
Lead-lag (S.LLAG).........................................9-59
LLA (Lower limit alarm)...................................3- 8
LLI (Lower limit alarm inhibition).....................3- 8
Local work memory.........................................3- 3
Loop memory ..................................................3- 4
Ind
Index - 1