Related Manuals for Accu-Scope EXC-100 Series
Summary of Contents for Accu-Scope EXC-100 Series
- Page 1 MANUAL EXC-100 MICROSCOPE SERIES 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com • info@accu-scope.com...
-
Page 2: Table Of Contents
– I ........................13 DJUSTING THE ONDENSER NSTALLING A ILTER ) ............................14 SING THE ARKFIELD OPTIONAL ................................ 14 TORING THE OWER TROUBLESHOOTING ................................ 15 MAINTENANCE ................................19 SERVICE ................................... 19 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... -
Page 3: Safety Notes
4. Store the instrument in a cool, dry environment. Cover the microscope with the dust cover when not in use. 5. ACCU-SCOPE® microscopes are precision instruments which require periodic preventative maintenance to maintain proper performance and to compensate for normal wear. An annual schedule of preventative maintenance by qualified personnel is highly recommended. -
Page 4: Introduction
Your microscope will last a lifetime if used and maintained properly. ACCU-SCOPE microscopes are carefully assembled, inspected and tested by our staff of trained technicians in our New York facility. Careful quality control procedures ensure each microscope is of the highest quality prior to shipment. -
Page 5: Components Diagram
EXC-100 MICROSCOPE SERIES COMPONENTS DIAGRAM Eyepiece Binocular Head Frame Objective Focus Tension Stage Adjustment Ring Illuminator Coarse Focusing Knob Fine Focusing Knob 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... - Page 6 EXC-100 MICROSCOPE SERIES Trinocular Head Eyepiece Lock Screw Nosepiece Frame Objective Stage Coarse Focusing Condenser Knob Vertical Fine Focusing Adjustment Knob Knob Horizontal Light Adjustment Knob Indicator Adjustment Light Knob 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com...
-
Page 7: Assembly Diagram
★ Before assembling, make sure there is no dust, dirt or other materials which will disturb it. Assemble carefully and do not scrap any part or touch the glass surface. 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... -
Page 8: Detailed Assembly
2. Fully insert the connector① of power cord into the power socket②, and make sure it connects well (see Fig.5). 3. Fully insert the other connector into the socket of power supply, and make sure it connects well. Fig. 5 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... -
Page 9: Adjustment & Operation
There are rechargeable batteries at the bottom of the microscope. Open the battery box to replace the battery（see Fig.6）. ★ Use the power cord provided with your microscope by ACCU-SCOPE. If it is lost or damaged, a replacement can be purchased from ACCU-SCOPE. -
Page 10: Adjusting Focus
(i.e., make it easier to turn the coarse focus knob). ★ Note that the fine focus tension is not affected by the focus tension Fig. 10 adjustment ring. 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... -
Page 11: Adjusting The Condenser (Aperture Diaphragm)
★ Be careful not to use too much solvent to clean the lens as this may also damage the lens in the long term. 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... -
Page 12: Adjusting Interpupillary Distance
4. If the image from the camera is rotated compared to the eyepieces, loosen the lock screw④ and rotate the camera until the images have the same alignment. Retighten the lock screw. 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... -
Page 13: Place The Specimen Slide
Adjusting the Condenser – Installing a Filter 1. Before installing the filter, rotate the condenser to the bottom and then open the filter holder. ★ Place the filter with the rough side downward. Fig. 16 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... -
Page 14: Using The Darkfield Stop (Optional)
Do not use strong force when the power cord is bent or twisted, otherwise it will be damaged. Use the power cord provided with your microscope by ACCU-SCOPE. If it is lost or damaged, a replacement can be purchased from ACCU-SCOPE. Always choose a power cord with Fig. 17 the same specifications as the original. -
Page 15: Troubleshooting
Remove bubbles Condenser aperture is closed or Open or close properly open too much Condenser is positioned too low Position the condenser slightly lower than the upper limit IMAGE PROBLEMS 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com... - Page 16 Focus travel set too high Set the focus travel lower No electrical power Check power cord connection Lamp does not light when switched Lamp bulb burnt out Replace bulb Fuse blown out Replace fuse 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com...
- Page 17 The LED bulb burns out often. The wrong LED bulb is used. Replace LED with a correct one. The illumination is not bright The wrong LED bulb is used. Replace the LED with a correct 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com...
- Page 18 EXC-100 MICROSCOPE SERIES enough. one. The light adjustment knob is set too Adjust the light intensity correctly. low. Replace light adjustment know The light adjustment knob is not assembly (rheostat). working correctly. 73 Mall Drive, Commack, NY 11725 • 631-864-1000 • www.accu-scope.com...
-
Page 19: Maintenance
ACCU-SCOPE at (631) 864-1000. This warranty is limited to the continental United States of America. All items returned for warranty repair must be sent freight prepaid and insured to ACCU-SCOPE INC., 73 Mall Drive, Commack, NY, 11725 – USA. All warranty repairs will be returned freight prepaid to any destination within the continental United States of America, for all foreign warranty repairs return freight charges are the responsibility of the individual/company who returned the merchandise for repair.