Soundoff Signal NEXUS TECHNOLOGY nFORCE LED Lightbar 24 Manual page 6

nFORCE™ LED Lightbar - 24"
Takedown and Work-light Configuration:
a. Apply voltage to Ignition Input Wire and then set Switch #2 on Breakout box to down (Switch #1 must be in Up position)
b. Determine which module inputs are needed for Takedowns or Work-lights
c. Apply voltage to the Takedown activation wire
d. Apply voltage to the light group wire(s) required (i.e. Front Inboard 1, Rear Inboard 2, etc.)
e. Momentarily apply voltage to the pattern select wire to change the color between Off, Color 1, Color 2, and Color 3.
NOTE: If configuring a single color or dual color module, make sure the chosen color is configured for Off and not a color which
does not exist on the module. The light-bar will flash color #1 of all modules configured for takedown. If a module flashes every 2
seconds and is not intended to be on when takedown is activated, repeat steps 'd' and 'e' until module no longer flashes.
f. Set Switch #2 on Breakout box to up position to save settings and return light-bar to normal operating mode
Scene light Configuration:
a. Apply voltage to Ignition Input Wire and then set Switch #2 on Breakout box to down (Switch #1 must be in Up position)
b. Determine which module inputs are needed for Scene Lighting
c. Apply voltage to the Scene light activation wire
d. Apply voltage to the light group wire(s) required (i.e. Front Inboard 1, Rear Inboard 2, etc.)
e. Momentarily apply voltage to the pattern select wire to change the color between Off, Color 1, Color 2, and Color 3.
NOTE: If configuring a single color or dual color module, make sure the chosen color is configured for Off and not a color which does not exist on
the module. The light-bar will flash color #1 of all modules configured for scene light. If a module flashes every 2 seconds and is not intended to
be on when scene light function is activated, repeat steps 'd' and 'e' until module no longer flashes.
f. Set Switch #2 on Breakout box to up position to save settings and return light-bar to normal operating mode
Stop / Tail / Turn (STT) Light Configuration:
a. Apply voltage to Ignition Input Wire and then set Switch #2 on Breakout box to down position (Switch #1 must be in Up position)
b. Determine which module inputs are needed for Stop / Tail / Turn Lights
c. Apply voltage to the Left Turn or Right Turn activation wires
d. Apply voltage to the light group wire(s) required (i.e. Rear Inboard 1, Rear Inboard 2, etc.)
e. Momentarily apply voltage to the pattern select wire to change the color between Off, Color 1, Color 2, and Color 3.
NOTE: If configuring a single color or dual color module, make sure the chosen color is configured for Off and not a color which does not exist on
the module. The light-bar will flash color #1 of all modules configured for STT function. If a module flashes every 2 seconds and is not intended
to be on when an STT function is activated, repeat steps 'd' and 'e' until module no longer flashes.
f. Set Switch #2 on Breakout box to up position to save settings and return light-bar to normal operating mode
Cruise Mode Configuration:
a. Apply voltage to Ignition Input Wire and then set Switch #2 on Breakout box to down position (Switch #1 must be in Up position)
b. Determine which module inputs are needed for cruise mode
c. Apply voltage to the Cruise Mode activation wire
d. Apply voltage to the light group wire(s) required (i.e. Front Corner, Front Inboard 1, etc.)
e. Momentarily apply voltage to the pattern select wire to change the color between Off, Color 1, Color 2, and Color 3.
NOTE: If configuring a single color or dual color module, make sure the chosen color is configured for Off and not a color
which does not exist on the module. The lightbar will flash color #1 of all modules configured for cruise mode. If a module
flashes every 2 seconds and is not intended to be on when Cruise mode is activated, repeat steps 'd' and 'e' until module no
longer flashes.
f. Set Switch #2 on Breakout box to up position to save settings and return light-bar to normal operating mode
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the automated message).
S U P E R I O R C U S TO M E R R E L AT I O N S H I P S . S M A RT LY D E S I G N E D L I G H T I N G & E L E C T R O N I C S O L U T I O N S .
6.
ELECTRICAL INSTALLATION (CONTINUED)
Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.
IMPORTANT INFORMATION:
nForce Lightbar - 24inch 09.13