Soundoff Signal NEXUS TECHNOLOGY nFORCE LED Lightbar 24 Manual page 5

nFORCE™ LED Lightbar - 24"
Warning Flash Pattern Configuration:
a. Apply voltage to Ignition Input Wire and then set Switch #2 on Breakout box to down position (Switch #1 must be in Up position)
b. Apply voltage to the activation wire of the function which requires pattern to be changed (i.e. Front Corner, Takedown, Left Alley, etc.)
c. Apply voltage to the Mode activation wire to configure mode 2 flash patterns, leave Mode activation wire floating to configure mode 1 flash patterns
d. Momentarily apply voltage to the pattern select wire to change the warning flash pattern
e. Set Switch #2 on Breakout box to up position to save settings and return light-bar to normal operating mode
NOTE: Takedown and Alley light patterns are limited to pattern #1 – 11
*fpm=Flashes per Minute
**fps=Flashes per Second
# Name
1 Random Single #1
2 Random Single #2
3 Quint
4 Quad 2
5 Q-Switch
6 Double
7 Power Pulse
8 RoadRunner
9 SlowRunner
10 Warp
11 Inter-cycle
12 Warp 1, 2, 3
13 E-Single
14 E-Double
15 E-Triple
16 Random Duo #1
17 Random Duo #2
18 Quint Duo
19 Quad 2 Duo
20 Q-Switch Duo
21 Double Duo
22 Power Pulse
23 RoadRunner Duo
24 SlowRunner Duo
25 Warp Duo
26 Inter-cycle Duo
27 Warp 1, 2, 3, Duo
28 Dual Color Flash 1
29 Dual Color Flash 2
30 Impact
31 Explosion
32 Tri Color Flash 1
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the automated message).
S U P E R I O R C U S TO M E R R E L AT I O N S H I P S . S M A RT LY D E S I G N E D L I G H T I N G & E L E C T R O N I C S O L U T I O N S .
5.
ELECTRICAL INSTALLATION (CONTINUED)
FLASH PATTERNS
SAE
Compliant Color
Timing
Yes
#1
No
#1
Yes
#1
Yes
#1
Yes
#1
Yes
#1
Yes
#1
Yes
#1
Yes
#1
No
#1
No
#1
No
#1
Yes
#1
Yes
#1
Yes
#1
Yes
#1/2
No
#1/2
Yes
#1/2
Yes
#1/2
No
#1/2
Yes
#1/2
Yes
#1/2
Yes
#1/2
Yes
#1/2
No #1/2
No #1/2
No #1/2
No #1/2
No #1/2
No #1/2
No #1/2
No #1/2/3
Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsigal.com.
Sequence fpm fps
Variable - -
Variable - -
Alternating 70 1.2
Variable - -
Variable - -
Alternating 115 1.9
Alternating 180 3.0
Alternating 115 1.9
Alternating 70 1.2
Alternating 350 5.8
Alternating - -
Variable - -
Alternating 125 2.1
Alternating 125 2.1
Alternating 125 2.1
Variable - -
Variable - -
Alternating 70 1.2
Variable - -
Variable - -
Alternating 115 1.9
Alternating 180 3.0
Alternating 115 1.9
Alternating 70 1.2
Alternating 350 5.8
Alternating - -
Variable - -
Variable - -
Variable - -
Variable - -
Variable - -
Alternating - -
IMPORTANT INFORMATION:
IMPORTANT
WHEN PASSING CABLES THROUGH FIREWALL OR OTHER
SHEETMETAL, INSERT GROMMET TO PROTECT THE CABLE!
WARNING
!
Route wires only in locations that are not subjected to
potential wear. Make sure to avoid routing wires in the
deployment area of your air bag. Refer to your vehicle's
owner's manual for airbag deployment zone.
nForce Lightbar - 24inch 09.13