Page 1
USER MANUAL ProlD Series Water Resistant RFID Access Control Reader Applicable Models: ProlD Series Version: 1.1 Date: April 2023 English Thank you for choosing our product. Please read the instructions carefully before operation. Follow these instructions to ensure that the product is functioning properly.
Page 2
ZKTeco supplied equipment vests in and is the property of ZKTeco. The contents hereof should not be used or shared by the receiver with any third party without the express written permission of ZKTeco.
Page 3
ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions due to any non-compliance of the instructions contained in this manual (ii) in case of operation of the machine/unit/equipment beyond the rate limits (iii) in case of operation of the machine and equipment in conditions different from the prescribed conditions of the manual.
Page 4
With years of experience in the industrialization of biometric verifications, ZKTeco was officially established in 2007 and now has been one of the globally leading enterprises in the biometric verification industry owning various patents and being selected as the National High-tech Enterprise for 6 consecutive years.
Page 5
ProlD Series Water Resistant RFID Access Control Reader User Manual Document Conventions Conventions used in this manual are listed below: GUI Conventions For Software Convention Description Bold font Used to identify software interface names e.g., OK, Confirm, Cancel. Multi-level menus are separated by these brackets. For example, File >...
ProlD Series Water Resistant RFID Access Control Reader User Manual Table of Contents 1 OVERVIEW ............................6 1.1 I ............................6 NTRODUCTION 1.2 F ..............................6 EATURES 1.3 A ............................... 6 PPEARANCE 1.4 S ............................8 PECIFICATIONS 2 TERMINAL AND WIRING DESCRIPTION ....................9 2.1 T...
Overview Introduction ProlD series metal reader is the latest access control reader launched by ZKTeco, which can be used with access control machines for more costeffective use of access control. There are two colors of black and white for customers to choose, using three installation specifications (Asian gang box, single gang box and mullion mount), standard ID, optional MF, recognition of the card distance of 0-5cm, support Wiegand and RS-485.
ProlD Series Water Resistant RFID Access Control Reader User Manual Specifications Items Specifications Operation Voltage 7 to 13V DC Current Draw ≤350mA 5V Processor 32-bit ARM Cortex-M0 48MHz Card Type ID/IC Card Read Range 0 to 5 cm Output Format...
ProlD Series Water Resistant RFID Access Control Reader User Manual Terminal and Wiring Description Terminal Description Figure 2-1 Terminal Description Table 2-1 Description of Terminal and Interfaces Name Interface Description 7 to 13V DC Input +12V Power Note: Recommended AC adapter: 7 to 13V, Current Draw ≤350mA 5V.
2.2.2 Controller Connection This ProlD series reader needs to be connected to a host machine in order to transmit card information via RS-485 or wiegand. The following is an example of the connection to InBio Series controller. 2.2.2.1 Connect the controller via RS485...
Page 12
ProlD Series Water Resistant RFID Access Control Reader User Manual Notes: A maximum of seven readers can be connected to one controller. Before connecting RS-485 readers, open the rear panel of the reader and set the RS-485 address of the reader via DIP switch according to the connection of each reader.
2.2.3 Access Control Device Connection This ProlD series reader can be connected to an access control device. The wiring below is an example of connection to an access control device via RS-485. Figure 2-5 Reader connect the access control device...
ProlD Series Water Resistant RFID Access Control Reader User Manual Notes: The reader RS-485 address defaults to 1. 2.2.4 Tamper Switch Connection When the tamper switch terminal is successfully connected to the controller, the device will not only send an alarm when the back panel of the device is opened, but also send an alarm signal to the software side.
Installation Set-up ProlD series reader can be installed on the wall alone or mounted to the wall by Asian gang box, single gang box and mullion mount. The following is an example of wall mounting and Asian gang box installation of ProlD102.
Step 4: Then insert the device into back plate. Step 5: Use security screw to fasten the device to the back plate. Figure 3-2 Install the ProlD series reader on the wall through Asian gang box Note: The installation method of single gang box is the same as that of Asian gang box. Only Asian gang box ...
ProlD Series Water Resistant RFID Access Control Reader User Manual Appendix 1 Buzzer, Indicator Light Prompt Instructions When the reader communicates via RS-485, the status of the buzzer and the indicator is shown in the table below. Note that when communicating via Wiegand, the status of the buzzer and indicator is controlled by the controller or the all-in-one access control device.
Appendix 2 Privacy Policy Notice: To help you better use the products and services of ZKTeco and its affiliates, hereinafter referred as “we”, “our”, or “us”, the smart service provider, we consistently collect your personal information. Since we understand the importance of your personal information, we took your privacy sincerely and we have formulated this privacy policy to protect your personal information.
Page 19
ProlD Series Water Resistant RFID Access Control Reader User Manual 3. Only your user ID is displayed by default. You can set whether to display other user verification information (such as Name, Department, Photo, etc.) under the Administrator privilege. If you choose to display such information, we assume that you are aware of the potential security risks (for example, your photo will be displayed on the device interface).
ProlD Series Water Resistant RFID Access Control Reader User Manual Appendix 3 Eco-friendly Operation The product's "eco-friendly operational period" refers to the time during which this product will not discharge any toxic or hazardous substances when used in accordance with the prerequisites in this manual.