ZKTeco ProFace X Series User Manual
  1. Manuals
  2. Brands
  3. ZKTeco Manuals
  4. IP Access Controllers
  5. ProFace X Series
  6. User manual

ZKTeco ProFace X Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ProFace X Series
User Manual
ProFace X Series
Date: May 2022
Doc Version: 1.0
English
Thank you for choosing our product. Please read the instructions carefully
before operation. Follow these instructions to ensure that the product is
functioning properly. The images shown in this manual are for illustrative
purposes only.
P a g e
| 1
For further details, please visit our Company's website
www.zkteco.com.
Copyright©2020 ZKTECO CO., LTD. All rights reserved.
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ProFace X Series and is the answer not in the manual?

Questions and answers

Related Manuals for ZKTeco ProFace X Series

Summary of Contents for ZKTeco ProFace X Series

  • Page 1 Follow these instructions to ensure that the product is functioning properly. The images shown in this manual are for illustrative purposes only. For further details, please visit our Company’s website www.zkteco.com. P a g e Copyright©2020 ZKTECO CO., LTD. All rights reserved.
  • Page 2 Copyright © 2022 ZKTECO CO., LTD. All rights reserved. Without the prior written consent of ZKTeco, no portion of this manual can be copied or forwarded in any way or form. All parts of this manual belong to ZKTeco and its subsidiaries (hereinafter the "Company" or "ZKTeco").
  • Page 3 ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions due to any non-compliance of the instructions contained in this manual (ii) in case of operation of the machine/unit/equipment beyond the rate limits (iii) in case of operation of the machine and equipment in conditions different from the prescribed conditions of the manual.
  • Page 4 User Manual About the Company ZKTeco is one of the world’s largest manufacturer of RFID and Biometric (Fingerprint, Facial, Finger-vein) readers. Product offerings include Access Control readers and panels, Near & Far-range Facial Recognition Cameras, Elevator/floor access controllers, Turnstiles, License Plate Recognition (LPR) gate controllers and Consumer products including battery-operated fingerprint and face-reader Door Locks.
  • Page 5 The general information which helps in performing the operations faster. The information which is significant. Care taken to avoid danger or mistakes. The statement or event that warns of something or that serves as a cautionary example. P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 6: Table Of Contents

    ....................................47 ARAMETERS ★ ..................................48 ONITORING ETTINGS ..................................... 49 ECURITY ETTING ......................................50 ACTORY ESET .................................. 51 EMPERATURE ANAGEMENT ★ ................................... 51 ETECTION ANAGEMENT PERSONALIZE SETTINGS ......................... 54 P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 7 ................ 98 EQUIREMENTS FOR OLLECTION AND EGISTRATION OF ISIBLE IGHT MAGES ........................99 EQUIREMENTS FOR ISIBLE IGHT IGITAL MAGE APPENDIX 2 ............................100 ........................................100 RIVACY OLICY ......................................102 FRIENDLY P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 8: Data Security Statement

    ZKTeco, as a smart product supplier, may also need to know and collect some of your personal information in order to better assist you in using ZKTeco's goods and services, and will treat your privacy carefully by developing a Privacy Policy.
  • Page 9 Do not keep the device in a place that vibrates. Handle the device with care. Do not place heavy  objects on top of the device. P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 10 The warranty service does not cover accidental damage, damage caused by mis-operation, and  damage due to independent installation or repair of the product by the user. P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 11: Overview

    User Manual Overview This document describes the operating procedure of ProFace X Series device. The operating modules of the device include User management, User role assignment, Device communication, Temperature detection, Access control, and so on. The device supports hassle-free access of users into the premises without compromising any security aspect thus ensuring protection.

  • Page 12: Palm Registration

    Try to keep your face in the center of the screen during registration. Please face the camera and stay still during face registration. The page looks like shown below: P a g e | 11 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 13: Standby Interface

    Do not cover the face, allow the device to recognize both the eyebrows and the face. Standby Interface After connecting the power supply, the home screen appears as shown below: P a g e | 12 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 14: Virtual Keyboard

    English keyboard. Press 123 to switch to the numeric and special character keyboard, and click ABC to return to the alphabetic keyboard. Click the input box, and virtual keyboard appears. Click ESC to delete the entered characters. P a g e | 13 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 15: Verification Mode

    1:1 (One to One) Palm Verification Mode Click the button on the main screen to open the 1:1 (One to One) palm verification mode. P a g e | 14 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 16 If the user has registered the face and password in addition to palm, and the verification method is set to palm/ face/ password, the following screen will appear. Select the palm icon to enter palm verification mode. P a g e | 15 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 17: Password Verification

    The Password Verification mode compares the entered password with the registered User ID and Password. Click the button on the main screen to open the 1:1 (One to One) password verification mode. Input the user ID and press OK. P a g e | 16 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 18 If an employee registers palm and face in addition to password, the following screen will appear. Select the icon to enter the password verification mode. Input the password and press OK. Successful Verification: P a g e | 17 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 19: Facial Verification

    The conventional method compares the acquired facial images with all the face data templates registered in the device. The following is the pop-up prompt box of comparison result. P a g e | 18 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 20 The following is the verification interface. P a g e | 19 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 21 When the user enabled the Display Thermodynamics Figure function, during the detection process, the thermal image of the person will be displayed in the top left corner of the device. P a g e | 20 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 22 This verification method compares the face captured by the camera with the facial template related to the entered user ID. Press on the main interface to open the 1:1 facial verification mode. Enter the User ID and click OK. P a g e | 21 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 23 After successful verification, the prompt "Successfully verified" will appear. If the verification is failed, it will prompt "Please adjust your position!". P a g e | 22 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 24: Combined Verification

    For example, if a user uses Face Registration but the verification mode is Face + Password, this user will never pass the verification. P a g e | 23 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 25: Main Menu

    Note: When users use the product for the first time, they should operate it after setting administrator privileges. Tap User Mgt. to add an administrator or edit user permissions as a super administrator. If the P a g e | 24 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 26 ProFace X Series User Manual product does not have an administrator setting, the system will show an administrator setting command prompt every time you enter the device menu. P a g e | 25 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 27: User Management

    During the initial registration, you can modify your ID, which cannot be modified after registration.  If a message "Duplicated ID" pops up, you must choose another ID.  P a g e | 26 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 28 The authentication is based on the authentication method(s) that the super administrator has registered. Please refer "2.6 Verification Mode". Register Palm Click Palm to open the palm registration page. Select the palm to be enrolled. P a g e | 27 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 29 User Manual Register Face Click Face to open the face registration page. Please face the camera and stay still during face registration. The registration interface is as follows: P a g e | 28 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 30 New users belong to Group 1 by default, and can be reassigned to other groups. The device supports up to 99 access control groups. Click Time Period, select the time period to use. P a g e | 29 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 31: Search For Users

    Click the search bar on the user list and enter the retrieval keyword (The keyword may be an ID, surname, or full name). The system will search for the users related to the information. P a g e | 30 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 32: Edit Users

    Choose a user from the list and click Delete to enter the delete user interface. Select the user information to be deleted and click OK. Note: If you select Delete User, all the information of the user will be deleted. P a g e | 31 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 33: User Role

    Click any role to set a defined role. Toggle the Enable Defined Role button to enable this defined role. Click Name and enter the name of the role. P a g e | 32 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 34 User Mgt. > New User > User Role. If no super administrator is registered, the device will prompt "Please register super administrator user first!" after clicking the enable bar. P a g e | 33 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 35: Communication Settings

    When the device needs to communicate with a PC over the Ethernet, you need to configure network settings and ensure that the device and the PC are connecting to the same network segment. Click Ethernet on the Comm. Settings interface. P a g e | 34 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 36: Pc Connection

    Identity number of the device, which ranges between 1 and 254. If the communication method is RS232/RS485, you need to input this device ID in the Device ID software communication interface. P a g e | 35 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 37: Wireless Network

    Wi-Fi Enabled: Tap on the required Tap on the password field to enter the network from the searched network list. password, and then tap on Connect to Wi-Fi (OK). P a g e | 36 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 38 IP Address IP address of the Wi-Fi network. Subnet Mask Subnet mask of the Wi-Fi network. Gateway Gateway address of the Wi-Fi network. P a g e | 37 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 39: Cloud Server Setting

    This function is enabled by default. This function can be enabled or disabled through the menu interface, and when changing the HTTPS status, the device will pop up a security prompt, and restart after confirmation. P a g e | 38 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 40: Wiegand Setup

    13 Wiegand26 bits, while the 26 bit is the odd parity bit of the 14 to 25 bits. The 2 to 25 bits are the card numbers. P a g e | 39 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 41 "C" denotes the card number; "E" denotes the even parity bit; "O" denotes the odd parity bit; "F" denotes the facility code; "M" denotes the manufacturer code; "P" denotes the parity bit; and "S" denotes the site code. P a g e | 40 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 42: Wiegand Output

    The time width represents the changes of the quantity of electric charge with Pulse Width(us) high-frequency capacitance regularly within a specified time. Pulse Interval(us) The time interval between pulses. ID Type Select between User ID and Access Card. P a g e | 41 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 43: System Settings

    The product supports the NTP synchronization time system by default. This function takes effect after Date and Time Auto Sync is enabled and the corresponding NTP server address link is set. P a g e | 42 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 44: Access Logs Setting

    2021. After restoring the factory settings, the time of the equipment will change to 18:30 on January 1, 2021. Access Logs Setting Click Access Logs Setting on the System interface. P a g e | 43 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 45 1 to 9 seconds. Face Comparison To set the facial template matching time interval as needed. The valid value is Interval (s) 0 to 9 seconds. P a g e | 44 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 46: Face Parameters

    When the similarity between the acquired facial image and all the registered Threshold facial templates is greater than this threshold, it indicates that the face has already been registered. P a g e | 45 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 47 It is convenient to judge whether the near-infrared spectral imaging is fake Detection photo and video. The larger the value, the better the anti-spoofing Threshold performance of near-infrared spectral imaging. P a g e | 46 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 48: Palm Parameters

    In 1:N Verification Method, only when the similarity between the verifying Palm 1:N Matching palm and all the registered palm is greater than this value can the verification Threshold succeed. P a g e | 47 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 49: Monitoring Settings

    Select whether to enable the server address. Once you have SIP Server connected to the server, you can call it by entering the username of the indoor station. P a g e | 48 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 50: Security Setting

    By default, this function is disabled. This function can be enabled or disabled Standalone via the menu interface. When it is switched on, a security prompt appears, and Communication the device will restart after you confirm. P a g e | 49 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 51: Factory Reset

    The Factory reset module restores the device, such as communication settings and system settings, to factory settings (does not clear the registered user data). Click Reset on the System interface. Click OK to reset. P a g e | 50 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 52: Temperature Management

    When the device temperature is lower than the set value, it will shut down High Temp. to Reset automatically to protect the hardware, the range is 60 to 80 (°C). Detection Management★ Click Detection Management on the System interface. P a g e | 51 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 53 To enable or disable the mask detection function. Enable Mask When it’s enabled, the device will identify whether the user is wearing a mask Detection or not during verification. P a g e | 52 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 54 Users may disable the function or set a value between 1 to 255. Firmware Update Choose whether to update the thermal imaging temperature detection module software version. ★ P a g e | 53 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 55: Personalize Settings

    You may customize the interface settings, audio and bell. Click Personalize on the main menu interface. Interface Settings You can customize the display style of the main interface. Click User Interface on the Personalize interface. P a g e | 54 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 56: Voice Settings

    Select whether to enable voice prompts during operating. Touch Prompt Select whether to enable keypad sounds. Volume Adjust the volume of the device and the valid value is 0 to 100. P a g e | 55 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 57: Bell Schedules

    Click Edit, the editing method is the same as the operations of adding a bell. Delete a Bell On the All Bell Schedules interface, tap the bell to be deleted. Tap Delete and select Yes to delete the bell. P a g e | 56 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 58: Punch States Options

    Fixed Mode: Only the fixed punch state key will be shown, and it cannot be switched. P a g e | 57 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 59: Shortcut Keys Mappings

    Users may define shortcuts as attendance status or functional keys. On the main interface, when the shortcut keys are pressed, the corresponding attendance status or function interface will quickly display. Click Shortcut Key Mappings on the Personalize interface. P a g e | 58 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 60: Data Management

    The Data Management interface is used to delete the relevant data in the device. Click Data Mgt. on the main menu interface. Delete Data Click Delete Data on the Data Mgt. interface. P a g e | 59 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 61 All or Delete by Time Range. Selecting Delete by Time Range, you need to set a specific time range to delete all data with the period. Select Delete by Time Range. Set the time range and click OK. P a g e | 60 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 62: Access Control

    In default settings, new users are allocated into the first group with the default group time zone and access combo as "1" and set in unlocking state. P a g e | 61 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 63: Access Control Options

    Normal Closed means the door is always closed when electricity is The supported verification mode includes Password/Face, User ID only, Verification Mode Password, Face only, and Face + Password. P a g e | 62 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 64: Time Rule Setting

    HH MM-HH MM, which is accurate to minutes according to the 24-hour clock. Click Time Rule Setting on the Access Control interface. P a g e | 63 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 65 Click the grey box to input a time zone to search. Enter the number of time zone (maximum: 50 zones). Click the date on which time zone settings is required. Enter the starting and ending time, and then press OK. P a g e | 64 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 66: Holiday Settings

    On the Holidays interface, select a holiday item to be deleted and click Delete. Click OK to confirm the deletion. After deletion, this holiday is no longer displayed on All Holidays interface. P a g e | 65 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 67: Combined Verification Settings

    4 consists of three people. The first person is from AC group 3, the second person is from AC group 5, and the third person is from AC group 8. P a g e | 66 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 68: Anti-Passback Setup

    The Wiegand format and Output type (User ID / Badge Number) adopted by the master device and slave device must be consistent. Click Anti-passback Setup on the Access Control interface. P a g e | 67 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 69: Duress Options Settings

    1 to 999 seconds. Set the 6-digit duress password. When the user enters this duress password for Duress Password verification, an alarm signal will be generated. P a g e | 68 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 70: Attendance Search

    2. Select the time range in which the records you want to search for records of all users, click OK you want to search for. without entering any user ID. P a g e | 69 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 71 User Manual 3. The record search succeeds. Click the record in 4. The below figure shows the details of the green to view its details. selected record. P a g e | 70 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 72: Autotest

    To test the RTC. The device tests whether the clock works normally and accurately Test Clock RTC with a stopwatch. Touch the screen to start counting and press it again to stop counting. P a g e | 71 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 73: System Information

    U disc export. Privacy Policy Note: The current privacy policy's text is only available in Simplified Chinese/English. However, translation of other multi-language content is underway, with more iterations. P a g e | 72 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 74: Connecting To Zkbiosecurity Mtd Software

    Server port: Set as the service port of ZKBioSecurity MTD (The default is 8088). Software Side Login to ZKBioSecurity MTD software, click System > Communication > Communication Device to set the ADMS service port, as shown in the figure below: P a g e | 73 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 75: Add Device On The Software

    Click Search, and it will prompt “Searching…….” After searching, the list and total number of access controllers will be displayed. Click Add after the device to complete adding. P a g e | 74 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 76: Add Personnel On The Software

    After setting all the parameters, click OK. Real-time monitoring on the Software Click Prevention > Epidemic > Real-time monitoring to view all the events include the user whose temperature is over the range: P a g e | 75 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 77 Click Epidemic > Statistics panel to view the analysis of statistical data and view the personnels with normal temperature. Note: For other specific operations, please refer ZKBioSecurity MTD User Manual. P a g e | 76 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 78: Lan Video Intercom Function Settings

    Double-click on the provided ZKBioVMSPlugin_sqlite.exe file to install the ZKBio VMS Plugin. Note: The ZKBioSecurity software and ZKBio VMS Plugin need to be opened simultaneously to recognize the intercom function. P a g e | 77 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 79: Configuration Parameters

    The username and the initial password are both admin. Note: When the Video-VMS plugin is connected successfully to the ZKBioSecurity, the password changes synchronously to the admin user password of the ZKBioSecurity. P a g e | 78 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 80 Server Address: Enter the ZKBioSecurity installation IP address. Server Port: The port is the service port set during installation (not the ADMS port). P a g e | 79 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 81 ProFace X Series User Manual Adding device on the ZKBioSecurity software Click Access > Device > Device > Search to add the device on the ZKBioSecurity software. P a g e | 80 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 82: Video Preview On The Zkbiosecurity Software

    Note: If the device is not added to the Video module, please check whether the parameter settings are correct. Video Preview on the ZKBioSecurity Software Click Video > Real-Time Monitoring > Video Preview to enter the preview interface of the device. P a g e | 81 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 83: Make A Call On The Device

    The server page pops up the call window by default, as shown in the following figure. Call Interface In-call Interface P a g e | 82 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 84 It is the Remote Open key, used to open the door remotely. The default lock drive time is 5 seconds. Note: If the device preview interface is opened on the ZKBioSecurity software, the call interface will no longer be displayed in this call window. P a g e | 83 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 85: Connecting To Zkbio Talk Software

    ZKBio Talk software. When the device-side video intercom parameters are set correctly, the device automatically pushes the device list on the left, as shown in following figure. P a g e | 84 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 86 When a user clicks icon on the main interface of the device to make a call, the software interface displays the IP address of the calling device in yellow. P a g e | 85 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 87 This is the Remote open key, used to open the door remotely. The default lock drive time is 5 seconds Note: Only the offline devices can be removed. P a g e | 86 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 88: Connecting To Zsmart App

    Tap on System > Video Intercom Parameters > QR Code Binding to show the QR code of the device. Click the icon in the upper right corner. P a g e | 87 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 89 ProFace X Series User Manual P a g e | 88 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 90: Video Phone Connection

    Click to open the door remotely. The unlocking record is saved in Me > Message Unlock Center. Note: For other specific operations, please refer to the ZSmartAPP User Manual. P a g e | 89 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 91: Connecting To Sip

    Set the IP address on the indoor station, Tap [Menu] > [Advanced] > [Network] > [1. Network] > [1. IPv4]. Note: In LAN, the IP addresses of the indoor station and the ProFace X must be in the same network segment. P a g e | 90 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 92 Custom the Punch Status Options  Use your browser to enter the address to log into WebSever, the address is the Serial IP Address:1443, for example: https: //192.168.163.99:1443. P a g e | 91 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 93 ProFace X Series User Manual Enter the WebSever account and password, the initial account is: admin, password: admin@123. P a g e | 92 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 94 Dialing Number: Customize the number of the indoor station, you can enter the value on ProFace X to call the indoor station quickly for video intercom. Once the form is set up and saved, upload the configuration form in WebSever. P a g e | 93 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 95 ProFace X to call the indoor station quickly for video intercom. After entering the dialing number, the corresponding IP address in IP Address the configuration data will be automatically paired. P a g e | 94 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 96 You can then tap [199] on the punch status options to directly implement the video intercom. Device Number  Enter the device number in the call screen. P a g e | 95 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 97: Sip Server

    Once the SIP is set up correctly, a green dot will appear in the upper right corner of the call page to indicate that the ProFace X is connected to the server. You can call the account name of the indoor station. P a g e | 96 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 98 ProFace X Series User Manual For details on the operation and use of the indoor station, please refer to the indoor station user manual. P a g e | 97 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 99: Requirements For Live Collection And Registration Of Visible Light Face Images

    Do not include more than one face in the capturing area. A distance of 50cm to 80cm is recommended for capturing the image (the distance is adjustable, subject to body height). P a g e | 98 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 100: Requirements For Visible Light Digital Face Image Data

    The captured person should be easily visible, natural in color, no harsh shadow or light spot or reflection in the face or background. The contrast and lightness level should be appropriate. P a g e | 99 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 101: Privacy Policy

    Privacy Policy Notice: To help you better use the products and services of ZKTeco (hereinafter referred as "we", "our", or "us") a smart service provider, we consistently collect your personal information. Since we understand the importance of your personal information, we took your privacy sincerely and we have formulated this privacy policy to protect your personal information.
  • Page 102 Welcome to visit our official website at any time to learn our latest privacy policy. P a g e | 101 Copyright©2022 ZKTECO CO., LTD. All rights reserved.

  • Page 103: Eco-Friendly Use

    The components which contain toxins or harmful elements are included due to the current economic or technical limitations which prevent their replacement with non-toxic materials or elements. P a g e | 102 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
  • Page 104 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright © 2022 ZKTECO CO., LTD. All Rights Reserved.

Table of Contents

Save PDF