Related Manuals for ZKTeco PA22
Summary of Contents for ZKTeco PA22
- Page 1 Quick Start Guide PA22 Version: 1.0 Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
-
Page 2: Device Overview
Device Overview Front Side 2.4 Inch TFT LCD Keypad & RF Card Area Reset Button LED Indicator Near-infrared Palm Speaker Recognition Sensor Back Bottom USB Slot Tamper switch Back Plate Terminal Block Mounting Hole Wiring Hole... -
Page 3: Device Dimensions
Device Dimensions 3.18" 0.76" (80.7mm) (19.4mm) 2.21" (56.1mm) 6.29" 4.97" (159.8mm) (126.1mm) 1.61" (41.0mm) Device Installation Install on the Wall Attach the mounting template sticker to the wall, and drill the holes according to the mounting paper. Fix the back plate on the wall with using wall mounting screws. Attach the device to the back plate from top to bottom. -
Page 4: Terminal Block
Terminal Block 4 Pin Cable Connectors 8 Pin Cable Connectors 7 Pin Cable Connectors 2 Pin Cable Connectors 12 Pin Cable Connectors RJ45-1 485B RS485B RJ45-2 485A Ethernet RJ45-3 RJ45-6 RS232 Auxiliary Wiegand BELL- Bell BELL+ BEEP BEEP Sensor GLED Green LED Button RLED... -
Page 5: Standalone Installation
Standalone Installation TCP/ IP Wireless Router Door Sensor Bell ALARM Alarm Lock Exit Button... -
Page 6: Power Connection
Power Connection Without UPS +12V DC 12V DC Adaptor With UPS (Optional) +12V DC Recommended Power Supply: 12V±10%, at least 3000MA. Use an AC adapter with a higher current ratings to share the power with other devices. -
Page 7: Ethernet Connection
Ethernet Connection LAN Connection Connect the device and the software over an Ethernet cable. An example is shown below: RJ45-1 RJ45-2 RJ45-3 RJ45-6 Network Cable Adaptor Default IP address: 192.168.1.201 IP address: 192.168.1.130 Subnet mask: 255.255.255.0 Subnet mask: 255.255.255.0 Click [Comm.] >... -
Page 8: Lock Relay Connection
Lock Relay Connection The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (Normally Opened when powered) is connected with “NO” and “COM” terminals, and the NC Lock (Normally Closed when powered) is connected with “NC” and “COM” terminals. The power can be shared with the lock or can be used separately for the lock, as shown in the example with NC Lock below: Device Not Sharing Power with the Lock BELL-... - Page 9 RS485 Connection RS485 Fingerprint Reader Connection 12V DC Adaptor 485B 485A RS485 Fingerprint Reader DIP Settings There are six DIP switches which are located on the back of RS485 ngerprint reader: switches 1 to 4 are for RS485 address, switch 5 is reserved, switch 6 is for noise reduction on long RS485 cable.
-
Page 10: Wiegand Output Connection
Wiegand Output Connection 485B 485A AC Adapter DC 12V, 3A +12V READER 1 Controller Wiegand Input Connection BEEP BEEP GLED GLED RLED RLED IWD1 DATA1 IWD0 DATA0 12VOUT +12V Wiegand Reader... -
Page 11: Device Operation
Device Operation User Registration [M/OK] When there is no super administrator set in the device, click to enter the menu. Add a new user and set their User Rule to Super Admin, then the system will ask for the administrator’s approval before allowing them to access the menu. For security reasons, we highly recommend that you register a super administrator promptly. - Page 12 Ethernet and Cloud Server Settings Click [M/OK] > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface. Click [M/OK] > [COMM.] > [Cloud Server Setting] to set the server address and server port, i.e., the IP address and port number of the server after the software is installed.
- Page 13 Access Control Setting Click [M/OK] > [Access Control] to enter the access control management interface and set relevant parameters for the access control.
- Page 14 Attendance Record Click [M/OK] > [Attendance Search] > [Attendance Record] to enter the records query interface, input the user ID and select the time range. The corresponding attendance logs will then be displayed.
- Page 15 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright 2023 ZKTECO CO., LTD. All Rights Reserved. ©...