Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Ballard Designs Manuals
  4. Indoor Furnishing
  5. Hutton MO569 COR
  6. Quick start manual

Ballard Designs Hutton MO569 COR Quick Start Manual

Corner work surface
Hide thumbs
1
2
3
4
5
6
7

Advertisement

Quick Links

Download this manual
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
PRODUCT NAME: Hutton *Corner Work Surface
ITEM NUMBER: MO569 COR
ASSEMBLED DIMENSIONS : 29.75"H x 24.75"L x 30.75"D
*Corner Work Surface requires use of additional Hutton Base Cabinets and Work Surface Tops (sold separately).
PRODUCTS ARE NOT INTENDED
MADE IN INDONESIA
FOR COMMERCIAL USE.
UPDATED: 5-4-2020
Page 1 of 7

Advertisement

loading
Need help?

Need help?

Do you have a question about the Hutton MO569 COR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Ballard Designs Hutton MO569 COR

Summary of Contents for Ballard Designs Hutton MO569 COR

  • Page 1 Customer Service: 800-367-2810 Online: www.ballarddesigns.com PRODUCT NAME: Hutton *Corner Work Surface ITEM NUMBER: MO569 COR ASSEMBLED DIMENSIONS : 29.75”H x 24.75”L x 30.75”D *Corner Work Surface requires use of additional Hutton Base Cabinets and Work Surface Tops (sold separately). PRODUCTS ARE NOT INTENDED MADE IN INDONESIA FOR COMMERCIAL USE.

  • Page 2: Required Tools

    Assemble in location for intended use. Ltr. Qty. Hardware Included REQUIRED TOOLS: Phillips Screwdriver Long Screws (35mm) -Two person assembly suggested. Short Screws (15mm) Remove all parts, hardware and protective packaging from carton and carefully arrange on a clean, Flat Washers level, padded surface.
  • Page 3 STEP 1: Attach Left Leg (K) and Right Leg (L) to Middle Leg (J) using 8 Long Screws (A) with Flat Washer (C) and Lock Washer (D) as illustrated below. Do not fully tighten until Step 2 is completed. STEP 2: First, insert Wood Dowels (E) into pre-drilled holes located at outer top edge of each Side Panel. Next, carefully place Top (I) onto Leg Assembly, align holes along edge then insert remaining 8 Long Screws (A) with Lock Washer (D) and Flat Washer (C).
  • Page 4 STEP 3: Corner Work Surface is equipped with Rotary Levelers under each Leg. If necessary, Unit may be adjusted by carefully lifting applicable corner and turning Leveler clockwise/counterclockwise. STEPS 4 through STEP 8 illustrate and explain connecting required Hutton Work Surface and Cabinet Base Units.
  • Page 5 STEP 5: Place Base Cabinets onto their backs and attach Corner Brackets (G) to bottom back edge of Base Cabinet for left side and Base Cabinet for right side. Use Short Screw (B) with Lock Washer (D) and Flat Washer (C). Firmly tighten. STEP 6: Turn Base Cabinets upright and place Work Surface onto top with Top Connector Brackets (F) oriented toward Corner Work Surface.
  • Page 6 STEP 7: Slide Left and Right Base Cabinets up to each end of Corner Work Surface. Align Top Connector Brackets and Corner Brackets with embedded T-nuts in Top and Legs. STEP 8: Secure Work Surface Top Connector Brackets (F) and each Corner Bracket (G) by inserting Short Screw (B) with Lock Washer (D) and Flat Washer (C) into T-nut and fully tightening.
  • Page 7 WALL ANCHORING HARDWARE (ANTI-TIP) Ltr. Qty. Hardware Included Small Screw WARNING Large Screw Tip-Over Hazard Bracket Serious or fatal crushing injuries can occur from a furniture tip-over Prevent tipping accidents. Anchor your furniture. Retention Belt 1. Place Desk against wall at desired location then locate and mark a Wall Stud behind unit. 2.