Contents Introduction Getting Started Download the App Sign up Log in App Languages Exit Using the App Binding Connection Energy Monitoring Settings Unbind Device Document Center Customer Service Account Security Modify Avatar & Username Change Password Cancel Account Practices Prioritize PV Charging Charge via Grid Feed to Grid Offset Peak-hour Energy Usage...
Firmware Upgrade, etc. Getting Started Download the App Scan the QR code below to download the BLUETTI App, or search for "BLUETTI" in the App Store or Google Play. Supported operating systems: Android 8.0 or above, iOS 11.0 or above.
Note: If you don't receive the email with verification code, check your Junk or Spam folder. If you still can't find the email, try "Get Code" again as there may be a delay. If the code is still unavailable, please contact BLUETTI customer service for assistance. Log in 1.
App Languages 1. Go to the Me page. 2. Tap Multi-language and select the language you want. 3. Tap OK to save the change. Exit 1. Go to the Me page. 2. Tap your name and go to the Account page. 3.
Note: Before binding, make sure your EP600 ESS is powered on with Bluetooth enabled (if necessary). • When you log in and access the My BLUETTI page for the first time, the app will automatically scan for nearby Bluetooth devices. Select your EP600 ESS from the pop-up list.
Page 7
2. On the Bind page, select your EP600 ESS from the Available Devices list. Note: Make sure you've enabled Bluetooth and location service (e.g. GPS) on your phone. If you can't find your EP600 ESS, get closer and Tap to refresh the list (recommended range: 5m).
Scan 2.Scan the QR code on the back of your EP600. Note: The EP600 ESS can be bound to one account only, while can be shared with multiple accounts. Connection The EP600 ESS supports both Bluetooth and WiFi connections. A simple comparison is as...
Page 9
• Bluetooth Connection If you've registered your EP600 ESS, go to the My BLUETTI page and tap under its name. You'll see in the upper left corner of your EP600 ESS's operation status page. If you haven't registered yet, open the app and tap...
Page 10
• WiFi Connection If you've registered your EP600 ESS, you can also connect to it via WiFi to get the most out of the BLUETTI app. To get started, you need to configure the network first. Configure the network ■...
Connect to EP600 ■ Go to My BLUETTI page, and tap the EP600 name area to connect via WiFi. You'll see in the upper left corner of operation status page. Energy Monitoring After you establish a successful connection, go to My BLUETTI page and tap EP600 name...
Page 12
The AC switch is on and the system is running on the grid. And the system charges from the grid. On-grid discharging: The AC switch is on and the system is running on the grid. And the system feeds back into the grid. Note: When the EP600 ESS is in operation, you can charge it with solar energy anyway.
Page 13
Serial number of the battery pack. State of Charge. The remaining battery level. Battery Status Include Charging, Discharging, and Standby. means that the battery pack is connected in parallel with EP600 Battery Parallel means that it's not connected in parallel with EP600.
• Power Statistics It allows you to view the PV Generation, Grid Consumption, Feed to Grid, and Load Consumption by day, month, or year. Settings Go to the operation status page and tap the icon in the upper right corner. You can optimize your power usage by customizing relevant settings such as Charge/Discharge time, SOC High/Low, etc.
Page 15
The information about EP600 and other related devices • AC The main switch of the EP600 ESS. Keep it on if you want the EP600 ESS to provide AC output. If it's off, the system has no input or output and will automatically shut down.
Page 16
SoC Low: It's set to 20% by default. This means that when the batterty level drops below 20%, the system will stop supplying power to your loads and the grid. Note: The grid will bypass the EP600 inverter to power your loads.
Page 17
Go to the Firmware Upgrade page and tap Start to upgrade. Once the upgrade is completed, it'll prompt that You're up to date. Note: This feature is only available when you connect to the EP600 ESS via Bluetooth. • Advanced Settings Go to the Settings page, and tap Advanced Settings to check and change more settings.
2. Select OK in the Unbind this device? pop-up. You can also unbind it by the following: 1. On the My BLUETTI page, select the EP600 you want to unbind. a.For an Android phone, long press on the name. b.For an iOS phone, swipe left the name.
Customer Service On the Services page, tap your product and submit the relavant service requests (e.g. Installation for EP600 ESS). You can also check the Ongoing and Finished requests. Account Security Modify Avatar & Username 1. On the Me page, tap on your avatar or name and you'll be taken to the Account page.
1.On the Me page, tap on your name or avatar and you'll be taken to the Account page. 2.Tap Security Center > Cancel Account, and follow the prompts. Note: Canceling your BLUETTI account will result in the permanent deletion of all relevant data, including your identity information, device data, service history, and other pertinent information.
Practices Prioritize PV Charging Switch on the PV switch of EP600 inverter and check for a successful solar input. Turn on the AC on the Setting page to enable the system to utilize solar energy whenever sunlight is available. Additionally, you can reduce your grid reliance by either disabling the Grid Charge Enable on the Advanced Settings page or setting a lower SoC High value.
Feed to Grid Turn on Feed to Grid on the Advanced Settings page. If you want to set a time period for grid feed-in, just follow the above steps and select Discharge instead.
Parallel Management. 2. Select the devices to be paralleled, and tap OK. 3. In the Parallel Settings pop-up, set one EP600 as the host and name it. 4. Tap OK to save the setting.
Need help?
Do you have a question about the EP600 and is the answer not in the manual?
Questions and answers