Step 1 Plug-In Auto Tuning - Panasonic SC-HT1000 Operating Instructions Manual

1
STEP Plug-in Auto Tuning
HOME THEATER
POWER POWER
VCR Plus+
Í POWER
DISPLAY OPEN/CLOSE
1 2
Numbered
4 5
buttons
7 8
CANCEL
0
SKIP
STOP
DIRECT NAVIGATOR
TOP MENU
3, 4, 2, 1
ENTER
ENTER
FUNCTIONS
MIX
L1/OPT 2CH
FRAME
PROG/CHECK ADD/DLT
ADD/DLT
MULTI REAR
STATUS MARKER
P.MEMORY
SHIFT SHIFT
EQ/SFC
X, W CHANNEL
POWER
REC
CHANNEL
DVD FM/AM REC MODE ERASE
DVD
After plugging the unit into your household AC outlet and pressing
[Í POWER] to turn the unit on for the first time, the unit assists you
to set the menu language, and automatically tunes in all the
channels it can receive and sets the clock.
The unit automatically determines the type of transmission
(airwaves or cable) and puts them into channels as follows.
Band
VHF
TV Mode
(Airwaves)
UHF
VHF
CATV LOW BAND
CATV MID/SUPER BAND
CATV Mode
CATV HYPER BAND
(Cable)
ULTRA BAND
SPECIAL CATV CHANNEL
Preparation
≥Confirm that the antenna is connected correctly.
≥Turn on the television and select the appropriate video input to
suit the connections to this unit.
≥Press [DVD] to select "DVD/CD" as the source.
TV
DVD FM/AM
DVD
INPUT SELECT TV/VIDEO
3
W X CH
CH
6
VOLUME
9
100
SLOW/SEARCH
PAUSE PLAY/x1.3
PLAY LIST
MENU
CH SELECT
RETURN
TEST PRO LOGIC
CM SKIP TIME SLIP
ERASE REC
S.POSITION C.FOCUS
F.Rec REC MODE
AUDIO SETUP
S W. LEVEL MUTING
VOLUME
OPEN/CLOSE
TUNING
MEMORY FM MODE
TIME SLIP TIME SLIP
DOWN UP
PHONES
Channel
2–13
14–69
2–13
95–99
14–36
37–65
66–94
100–125
1
1
Press [Í POWER] to turn the unit on.
Select Language
Seleccione la Lengua
Sélection de Langue
English
Español
Français
Press ENTER
Pulse ENTER
Appuyer sur ENTER
2
Press [3, 4] to select the menu
language and press [ENTER].
3
Press [ENTER] to start Plug-in Auto
Tuning.
Auto Channel Setting
1
CH.
Auto Channel Setting
Proceeding . . .
1 1 1
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished. If the clock is an hour slower or
faster than the actual time, go to "Time Zone Adjust" to
correct it (➡page 43).
4
When the display shows the correct time
Press [ENTER] to complete Plug-in
Auto Tuning.
∫ If the unit couldn't set the clock automatically
Press [ENTER] to show the "Manual Clock Setting" screen. Set the
time manually (➡page 43).
∫ To start Plug-in Auto Tuning again (after
relocation, for example)
Antenna system, channel caption, and VCR Plusr guide
channel settings all revert to the default values when you
perform the procedure below. Timer recording settings are
also cleared.
When the unit is on and stopped
1 Press and hold [X CHANNEL] and [W CHANNEL] on the
main unit for about five seconds.
The unit turns off.
2 Press [Í POWER] to turn the unit on.
Follow the above steps 2–4.
∫ If Plug-in Auto Tuning fails (➡page 40, Antenna
System and Auto Channel Setting)
Adding and deleting channels
Add or delete channels if necessary channels are not set or
unnecessary channels are set.
While this unit is receiving the antenna signal (but not during
recording):
1
Press the numbered buttons to select
a channel.
[0] ➡ [5]
e.g., "5":
[1] ➡ [5]
"15":
"115": [100] ➡ [1] ➡ [5]
≥You can also use [W X CH] when you
are going to delete a channel.
2
Press [ADD/DLT].
The channel is deleted if it was set or added if it was not set.
e.g.,
Repeat steps 1 and 2 as necessary.
Unit's display
CH
CHANNEL 15 DELETED
RQT7061
9