Error Messages - Panasonic SC-HT1000 Operating Instructions Manual

Error messages

On the television
Cannot finish recording
completely.
Cannot record on the disc.
Contents of this disc are
protected.
Disc is full.
Error has occurred. Please
press ENTER.
Finalizing is necessary for
compatible playback.
No disc.
Please check write protect tab
on the disc.
Please set clock.
This disc cannot be read.
This disc may not be played in
your region.
This is non-recordable disc.
This disc is not formatted
properly.
Please format the disc in 'DISC
SETTING' to record.
Your selection exceeds the
recorder's rating limit.
On the unit's display
CHK REMOTE
("∑" stands for a number.)
AF F61
DIGITAL UNLOCK
NO READ
SELF CHECK
U14
U99
UNSUPPORT
≥The program was copy-guarded.
≥No space left on the disc.
➡Create space by erasing any unwanted programs. [RAM]
➡Use a new disc. [RAM] [DVD-R]
≥Recording was not completed for some other reason.
≥The disc is scratched. Use another disc.
≥The disc is dirty.
≥You inserted an incompatible disc.
≥The program is write-protected. Cancel the protection.
≥The disc is write-protected. Cancel Disc Protection.
≥No space left on the disc.
➡Create space by erasing any unwanted programs. [RAM]
➡Use a new disc. [RAM] [DVD-R]
≥A serious, but temporary error has occurred and one of the unit's safety devices has
activated. Press [ENTER]. The unit switches to the standby mode. Press [Í POWER] to
turn the unit on again.
≥To enable playback of your DVD-R on compatible equipment, it is necessary to finalize it.
≥You haven't inserted a disc. Correctly insert a disc that this unit can use.
≥The disc is upside down. If it is a single-sided disc, insert it so the label is facing up.
≥The write-protect tab on the cartridge is set to PROTECT.
Use a ballpoint pen or similar to release the write protection.
≥The clock is not set.
≥You inserted an incompatible disc.
≥You tried to play a disc with a region number different from this unit's region number. This
unit can only play discs with the region numbers compatible with this unit (1, All, or
including the number 1).
≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R.
≥You inserted an unformatted DVD-RAM. Format the disc with this unit.
≥A ratings level has been set for DVD-Video with this unit. Unlock the unit with "Ratings" in
"Disc".
≥The remote control and main unit are using different codes. Change the code on the
remote control.
≥Check and correct the speaker cord connections.
If this does not fix the problem, there is a power supply problem. Consult the dealer.
≥There is no signal input to the L1 OPTICAL IN terminal.
➡Make sure to check the connections and if the power of the connected equipment is
turned on.
≥The disc is dirty or badly scratched.
➡Clean the disc if it is dirty.
➡The disc cannot be played if it is scratched and this display doesn't disappear.
≥The unit cannot read the disc.
≥You have used a DVD-RAM/PD lens cleaner and it has finished.
≥There was a power failure or the AC plug was disconnected while the power was on. The
unit is carrying out its recovery process. Wait until the message disappears.
≥The unit is hot.
➡The unit switches to standby automatically for safety reasons and you cannot operate it.
Wait for about 30 minutes for the service number to disappear.
➡Select a position with good ventilation when installing the unit.
➡Do not block the cooling fan on the rear of the unit.
≥The unit fails to operate properly. Press [Í POWER] to switch the unit to standby. Now
press [Í POWER] again to turn the unit on.
≥You have inserted a disc the unit cannot play or record on.
≥The signal input into the L1 OPTICAL IN terminal is not Dolby Digital or Linear PCM.
Page
—
30
—
—
—
53
8
30
32
30
—
—
33
8
12
—
PROTECT
43
8
Cover
page
8
33
38
42
Setup
Guide
—
53
—
—
53
—
—
—
—
—
8
—
RQT7061
47